Furuno 500 manual Steering Mode

Page 29

3. STEERING MODE

5.Press the [TURN] key to show the TURN menu.

6.Rotate the course control knob to choose “RADIUS OF ORBIT”, and then press it.

The current value is circumscribed with a double rectangle.

7.Rotate the course control knob to set the spiral speed. (Setting range: 0.05 to 9.99 nm)

8.Press the course control knob.

9.Reduce boat’s speed less than 10 kt.

10.Rotate the course control knob to select "◄ SPIRAL" or "SPIRAL ►".

11.Press the course control knob to start the spiral function.

The message “START TO TURN BY FISHING MODE” appears, and the boat runs for the distance set at step 7, and then starts making a spiral similar to the figure on the previous page.

If the boat's speed becomes more than 10 kt while orbiting, the message "TOO FAST TO FISHING MODE. PLEASE SLOW DOWN LESS THAN 10 kt. PUSH MENU KEY TO CANCEL AND GO TO AUTO MODE." appears. Reduce boat’s speed less than 10 kt. In this case, the boat runs as shown on page 3-11.

12.To escape from the SPIRAL while it is in use, press [STBY] key.

3-13

Page 28 Page 30
Image 29
Page 28 Page 30
Contents
Model NAVpilot-500 00014698415 General How to discard this product How to discard a used batteryImportant Notices Safety Instructions Table of Contents Index Word to the Owner of the NAVpilot-500 FeaturesForeword System configuration of NAVpilot-500 System ConfigurationPrinciple of Autopilot Principle of the AutopilotPrinciple of Operation Control unit, front view Basic OperationOperating Controls Startup sequence Turning the power offTurning On/Off Choosing the display mode Adjusting Brilliance and ContrastDisplays Contrast, brilliance windowSelecting data Displayed data Analog indicator selectionPort Stbd Available graphics for graphic displaySteering Modes Stby ModeStby mode display ex. Normal Display Auto mode display Normal display Auto ModeUsing the Auto mode Advanced Auto mode display ex. Normal display Advanced Auto modeEnabling the Advanced Auto mode Advanced auto options windowNAV mode display Normal display NAV ModeStarting the NAV mode NAV mode, Course and XTE Selecting sailing method of NAV modeNav mode options window Waypoint switching options window Switching waypointSteering Mode Turn menu Turn Mode Example of 180º maneuver in turn mode 180º Turn for Auto mode only 360º Turn for Auto mode only Example of 360º maneuver in turn modeExample of orbit maneuver ex. clockwise OrbitTo escape from the Orbit while it is in use, press Stby key Spiral Example of spiral maneuver in turn modeSteering Mode Figure Eight Example of Figure Eight in NAV modeTLL navigation Navigating to TLL pointDial type remote controller FAP-5551 Remote ModeRotating dial Turning power off dial typeNFU No Follow-Up mode display Turning power on, button and lever type remote controllersTurning power off, button and lever type remote controllers Operating remote controller ex. button and lever typesDodge mode display Dodge ModeDodging in Stby mode 359 Dodging in Auto or NAV modeThis page is intentionally left blank Menu Operation Stby Mode MenuStby mode menu Parameter setup menu Setting parametersSelecting the method of entering the parameter Sea state options windowDeviation level options window MANUAL-CALMExample of Manual parameter Setting parameters manuallyRudder angle and rudder gain setting Track line and weather setting valueWeather Rudder GainCounter Rudder General guidelines for setting rudder gainGeneral guidelines for setting counter rudder gain Auto trim options window Adjusting the sensitivity in monitoring the boat’s trimNAV Mode When towing a netNav mode data source window Auto net towing options windowWaypoint Switching Fish ModeRadius of Orbit Spiral SpeedSystem setup menu Setting other menu itemsActivating key beep Key beep options windowLock options window Locking the control unitSetting the panel dimmer Alarm menu AlarmsAlarm Menu Audio alarm options window Selecting the alarm buzzerAlarm interval options window Selecting the beep patternWatch alarm options window Setting the watch alarmSetting the heading deviation alarm XTE alarm options window Setting the cross-track error limitSpeed alarm options window Setting the speed alarmDepth alarm options window Setting the depth alarmSetting the trip distance alarm Setting the temperature alarmTemp alarm options window Log trip options windowLog trip clear options window Clearing the trip distanceAlarm Information Alarm messages, their meanings and priorities Alarm messagesPreventive Maintenance Maintenance & TroubleshootingMaintenance program Check point RemedyDiagnostics Replacement of FuseParts Name Type Code No Remarks Test options windowHeading Sensor Test Processor Unit TestController Unit Test Screen Test Keyboard TestRudder test Rudder Setup and Auto TestSystem data screen Clearing MemoriesSystem Data Error message Meaning Remedy Error MessagesError messages Error messages con’t MN-1 Menu TreeMN-2 Auto mode menuInterface Control UnitProcessor Unit Coating Color Power SupplyEnvironmental Conditions IN-1 Index
Related manuals
Manual 2 pages 40.46 Kb
Top Page Image Contents