Furuno 500 manual Navigating to TLL point, TLL navigation

Page 31

3. STEERING MODE

Navigating to TLL point

When TLL (Target Latitude and Longitude) data is input from a radar or echo sounder connected in the STBY, AUTO or NAV mode, the TURN menu appears. Then, you may choose how to progress towards that position, from ORBIT (port direction, starboard direction) or FIGURE EIGHT. (You may also continue current steering mode, by choosing OFF.) For this mode, own ship’s position L/L data and waypoint L/L data are required.

ORBIT

The boat makes circles around the TLL point.

SPIRAL

The boat goes to the TLL point spirally. After arriving to the TLL, the boat begins orbiting around there.

FIGURE EIGHT

The boat automatically returns to the TLL position when it goes more than a distance (set on menu) away from the TLL position.

Orbit around the TLL

TLL

TLL

Distance set on menu

Orbit maneuver

Figure eight maneuver

 

 

 

Orbit around the TLL

TLL

Spiral maneuver

TLL navigation

3-15

Image 31 Contents
Model NAVpilot-500 00014698415 Important Notices How to discard this product How to discard a used batteryGeneral Safety Instructions Table of Contents Index Foreword FeaturesWord to the Owner of the NAVpilot-500 System configuration of NAVpilot-500 System ConfigurationPrinciple of Autopilot Principle of the AutopilotPrinciple of Operation Operating Controls Basic OperationControl unit, front view Turning On/Off Turning the power offStartup sequence Contrast, brilliance window Adjusting Brilliance and ContrastChoosing the display mode DisplaysSelecting data Displayed data Analog indicator selectionPort Stbd Available graphics for graphic displayStby mode display ex. Normal Display Stby ModeSteering Modes Using the Auto mode Auto ModeAuto mode display Normal display Advanced auto options window Advanced Auto modeAdvanced Auto mode display ex. Normal display Enabling the Advanced Auto modeStarting the NAV mode NAV ModeNAV mode display Normal display Nav mode options window Selecting sailing method of NAV modeNAV mode, Course and XTE Waypoint switching options window Switching waypointSteering Mode Turn menu Turn ModeExample of 360º maneuver in turn mode 180º Turn for Auto mode onlyExample of 180º maneuver in turn mode 360º Turn for Auto mode onlyExample of orbit maneuver ex. clockwise Orbit To escape from the Orbit while it is in use, press Stby key Spiral Example of spiral maneuver in turn modeSteering Mode Figure Eight Example of Figure Eight in NAV modeTLL navigation Navigating to TLL pointDial type remote controller FAP-5551 Remote ModeRotating dial Turning power off dial typeNFU No Follow-Up mode display Turning power on, button and lever type remote controllersTurning power off, button and lever type remote controllers Operating remote controller ex. button and lever typesDodging in Stby mode Dodge ModeDodge mode display 359 Dodging in Auto or NAV modeThis page is intentionally left blank Stby mode menu Stby Mode MenuMenu Operation Sea state options window Setting parametersParameter setup menu Selecting the method of entering the parameterDeviation level options window MANUAL-CALMExample of Manual parameter Setting parameters manuallyRudder Gain Track line and weather setting valueRudder angle and rudder gain setting WeatherGeneral guidelines for setting counter rudder gain General guidelines for setting rudder gainCounter Rudder Auto trim options window Adjusting the sensitivity in monitoring the boat’s trimAuto net towing options window When towing a netNAV Mode Nav mode data source windowSpiral Speed Fish ModeWaypoint Switching Radius of OrbitKey beep options window Setting other menu itemsSystem setup menu Activating key beepLock options window Locking the control unitSetting the panel dimmer Alarm Menu AlarmsAlarm menu Selecting the beep pattern Selecting the alarm buzzerAudio alarm options window Alarm interval options windowSetting the heading deviation alarm Setting the watch alarmWatch alarm options window XTE alarm options window Setting the cross-track error limitSpeed alarm options window Setting the speed alarmDepth alarm options window Setting the depth alarmLog trip options window Setting the temperature alarmSetting the trip distance alarm Temp alarm options windowLog trip clear options window Clearing the trip distanceAlarm Information Alarm messages, their meanings and priorities Alarm messagesCheck point Remedy Maintenance & TroubleshootingPreventive Maintenance Maintenance programTest options window Replacement of FuseDiagnostics Parts Name Type Code No RemarksController Unit Test Processor Unit TestHeading Sensor Test Screen Test Keyboard TestRudder test Rudder Setup and Auto TestSystem Data Clearing MemoriesSystem data screen Error messages Error MessagesError message Meaning Remedy Error messages con’t MN-1 Menu TreeMN-2 Auto mode menuProcessor Unit Control UnitInterface Environmental Conditions Power SupplyCoating Color IN-1 Index
Related manuals
Manual 2 pages 40.46 Kb