NEC PX-61XM3G user manual Part Names and Function, Front View

Page 11

Part Names and Function

Front View

VOLUME				INPUTSELECT
MENU/ ENTER DOWN	UP	LEFT/ -	RIGHT/ +	/EXIT

CONFIDENTIAL

7

6

5

4

1

3

2

qPower

Turns the monitor’s power on and off.

wRemote sensor window

Receives the signals from the remote control.

ePOWER/STANDBY indicator

When the power is on ............................. Lights green. When the power is in the standby mode ... Lights red.

rINPUT SELECT / EXIT Switches the input.

The available inputs depend on the settings of “ BNC INPUT” , “ D-SUB INPUT” , “ RGB SELECT” and “ DVI SET UP” .

Functions as the EXIT buttons in the On-Screen Menu (OSM) mode.

tLEFT/– and RIGHT/+

Enlarges or reduces the image. Functions as the CURSOR ( / ) buttons in the On-Screen Menu (OSM) mode.

yVOLUME DOWN and UP

Adjusts the volume. Functions as the CURSOR (▲/ ▼ ) buttons in the On-Screen Menu (OSM) mode.

uMENU/ENTER

Sets the On-Screen Menu (OSM) mode and displays the main menu.

WARNING

The Power on/off switch does not disconnect the plasma display completely from the supply mains.

Note: This plasma monitor has the capasity to display images when connected to European DVD players with a SCART output signal, which is RGB with composite sync.

Your dealer can supply a special SCART cable, which will enable you to use the RGB with composite sync signal. To obtain the special cable as well as for further information, please contact your dealer.

Please refer to page E-21 for selection of the correct mode in the on-screen manager.

Downloaded From TV-Manual.com Manuals

E-7

4-11

Image 11

Contents PlasmaSync Plasma Monitor Signals HD/DVD/DTV input signals supported on this systemSupported resolution Table of Signals SupportedImportant Information English Deutsch Français Español Italiano Important Information PrecautionsContents Ventilation Requirements for enclosure mounting InstallationCables Video signal RGB/DVD/HD signalCreating a video wall Cable ManagementHandling the remote control How to use the remote controlBattery Installation and Replacement Using the wired remote control modeFront View Part Names and FunctionRear View/ Terminal Board Remote Control Basic Operations Wide Operations When viewing videos or digital video discsTrue When Picture Size is set to OFF Supported resolution Picture Size settingShowing a couple of pictures on the screen at the same time Operations in the Side-by-side modeSplit Screen Operations Zooming up pictures Operations in the Picture-in-picture modeSelecting the input signals to be displayed Adjusting the OSM controlsMenu Operations Advanced menu modeMenu Tree ResetLanguage Restoring the factory default settingsReducing noise in the picture Picture Settings MenuAdjusting the picture Setting the color temperatureChanging the Gamma Curve Adjusting the color to the desired levelMaking the Low Tone adjustments Adjusting the colorsAdjusting the Position, Size, Fine Picture, Picture Adj Audio Settings MenuImage Adjust Settings Menu Setting the allocation of the audio connectorsSetting the RGB1 connector Option1 Settings MenuSetting the on-screen menu Setting the BNC connectorsSetting high definition images to the suitable screen size Setting the Input SkipResetting to the default values POWER/STANDBY indicator Option2 Settings MenuSetting the power management for computer images Setting the picture to suit the movieSetting the time Orbiter settingsInverse Settings Orbiter Function settingsGray Level settings Setting the gray level for the sides of the screenSetting the screen size for S1/S2 video input Soft Focus settingsUsing the timer Option3 Settings MenuSetting the picture size for RGB input signals Setting the signal and black level for DVI signalSpecial characters in the Program Timer screen Program Timer settingsTo reset the program To reset the dataEnabling/disabling the front panel controls Setting the power on modeEnabling/disabling remote control wireless transmission Loop Out settingVideo Wall setting ID number settingOn Delay settings DISP. Mode settingsAuto ID settings Image Adjust settingsPLE Link PLE Link settingsRepeat Timer settings Repeat TimerDisplaying still images in the sub screen Option4 Settings MenuErasing the sub screen image when there is No input signalSetting the menu mode Advanced OSM Settings MenuLanguage Settings Menu Switching the input source quicklyVideo signal formats Color System Settings MenuSetting the video signal format Example Setting the color system to 3.58 NtscPin Assignments External ControlSymptom Checks Remedy Troubleshooting