NEC PX-61XM3G user manual Important Information

Page 4

CONFIDENTIAL

*1 Only when using a graphic accelerator board that is capable of displaying 852480.

*2 This signal is converted to a 1024 dots640 lines signal.

*3 The picture is displayed in the original resolution. The picture will be compressed for other signals.

*4 Aspect ratio is 5:4. This signal is converted to a 960 dots768 lines signal.

*5 Normally the RGB select mode suite for the input signals is set automatically. If the picture is not displayed properly, set the RGB mode prepared for the input signals listed in the table above.

*6 To connect the monitor to Macintosh computer, use the monitor adapter (D-Sub 15-pin) to your computer's video port.

*7 Other screen modes (ZOOM and STADIUM) are available as well.

*8 When viewing a moving picture at a vertical frequency greater than 65Hz, the picture may sometimes be unstable (jumpy). If this occurs, please set the refresh rate of the external equipment to 60Hz.

To view 480I@60Hz (480 interlaced lines, 60Hz refresh rate) or 576I@50Hz (567 interlaced lines, 50Hz refresh rate) when sync polarity is “ Sync on Green” , set “ RGB SELECT” to “ MOTION” .

*9 CVT standard compliant.

NOTE:

While the input signals comply with the resolution listed in the table above, you may have to adjust the position and size of the picture or the fine picture because of errors in synchronization of your computer.

When a 1280 dots 1024 lines signal or 1600 dots 1200 lines signal is input to the monitor, the picture will be compressed.

This monitor has a resolution of 1365 dots  768 lines. It is recommended that the input signal should be XGA, wide XGA, or equivalent.

With digital input some signals are not accepted.

The sync may be disturbed when a nonstandard signal other than the aforementioned is input.

If you are connecting a composite sync signal, use the HD terminal.

What is HDCP/HDCP technology?

HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).

If you are unable to view material via the DVI input, this does not necessarily mean the PDP is not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).

“IBM PC/AT” and “ XGA” are registered trademarks of International Business Machines, Inc. of the United States.

“Apple Macintosh” is a registered trademark of Apple Computer, Inc. of the United States.

Important Information

Warning

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on apparatus.

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures.

NOTE:

When you connect a computer to this monitor, use an RGB cable including the ferrite core on both ends of the cable. And regarding DVI and power cable, attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory CE or C-Tick standards.

Set the ferrite cores on both ends of the DVI cable (not supplied), and both ends of the power cable (supplied). Close the lid tightly until the clamps click.

Use the band to fasten the ferrite core (supplied) to the DVI cable.

DVI cable (not supplied)

 

 

band

band

Connector

core (small)

core (small)

Power cable (supplied)

core (large)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

core (large)

 

 

 

Downloaded From TV-Manual.com Manuals

E-3 4-4

Image 4
Contents PlasmaSync Plasma Monitor HD/DVD/DTV input signals supported on this system SignalsTable of Signals Supported Supported resolutionImportant Information English Deutsch Français Español Italiano Precautions Important InformationContents Installation Ventilation Requirements for enclosure mountingVideo signal RGB/DVD/HD signal Creating a video wallCable Management CablesHow to use the remote control Battery Installation and ReplacementUsing the wired remote control mode Handling the remote controlPart Names and Function Front ViewRear View/ Terminal Board Remote Control Basic Operations When viewing videos or digital video discs Wide OperationsWhen Picture Size is set to OFF  Supported resolution Picture Size setting TrueSplit Screen Operations Operations in the Side-by-side modeShowing a couple of pictures on the screen at the same time Operations in the Picture-in-picture mode Selecting the input signals to be displayedAdjusting the OSM controls Zooming up pictures Advanced menu mode Menu OperationsReset Menu Tree Restoring the factory default settings LanguagePicture Settings Menu Adjusting the pictureSetting the color temperature Reducing noise in the pictureAdjusting the color to the desired level Making the Low Tone adjustmentsAdjusting the colors Changing the Gamma CurveAudio Settings Menu Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Setting the RGB1 connectorResetting to the default values Setting the Input SkipSetting high definition images to the suitable screen size Option2 Settings Menu Setting the power management for computer imagesSetting the picture to suit the movie POWER/STANDBY indicatorOrbiter settings Inverse SettingsOrbiter Function settings Setting the timeSetting the gray level for the sides of the screen Setting the screen size for S1/S2 video inputSoft Focus settings Gray Level settingsOption3 Settings Menu Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal Using the timerProgram Timer settings To reset the programTo reset the data Special characters in the Program Timer screenSetting the power on mode Enabling/disabling remote control wireless transmissionLoop Out setting Enabling/disabling the front panel controlsID number setting Video Wall settingDISP. Mode settings Auto ID settingsImage Adjust settings On Delay settingsPLE Link settings Repeat Timer settingsRepeat Timer PLE LinkOption4 Settings Menu Erasing the sub screen image when there isNo input signal Displaying still images in the sub screenAdvanced OSM Settings Menu Language Settings MenuSwitching the input source quickly Setting the menu modeColor System Settings Menu Setting the video signal formatExample Setting the color system to 3.58 Ntsc Video signal formatsExternal Control Pin AssignmentsTroubleshooting Symptom Checks Remedy