NEC PX-61XM3G user manual Rear View/ Terminal Board

Page 12

CONFIDENTIAL

Rear View/ Terminal Board

C

E

F

G

H

I

J

K

		VIDEO 1	VIDEO
VIDEO 3			VIDEO 2
(			AUDIO 1
MONO
)	L	R
	Y
	Cb/Pb Cr/Pr		DVD1 / HD1
(			AUDIO 2
MONO
)	L	R
	Cr/Pr	R/
	G/ Y		RGB2
	Cb/Pb	B/	/ DVD2
	HD		/ HD2
	VD
			RGB 1
(			AUDIO 3
MONO
)	L	R
	DV I
	(		RGB 3
	Digital		RGB 3
	RGB
	)
	External Control
	I N
	REMOTE
	OUT

D

A B

AAC IN

Connect the included power cord here.

BEXT SPEAKER L and R

Connect speakers (optional) here. Maintain the correct

polarity. Connect the (positive) speaker wire to the EXT SPEAKER terminal and the (negative)

speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels.

Please refer to your speaker’s owner’s manual.

CVIDEO1, 2, 3 (BNC, RCA, S-Video)

Connect VCR’s, DVD’s or Video Cameras, etc. here. VIDEO1 can be used for Input or Output (see page E- 5).

DAUDIO1, AUDIO2, AUDIO3 These are audio input terminals.

The input is selectable. Set which video image to allot them from the audio menu screen.

EDVD1 / HD1

Connect DVD’s, High Definition or Laser Discs, etc. here.

FRGB2/ DVD2/ HD2

RGB2:	You can connect an analog RGB signal
	and the syncronization signal.

DVD2/ HD2: You can connect DVDs, High Definition sources, Laser Discs, etc. here.

This input can be set for use with an RGB or component source (see page E-21)

HRGB3 (DVI 24pin)

Connect a digital signal (TMDS) from a source with a DVI output.

This input can be set for use with an RGB/PC3 (see page E-26)

IEXTERNAL CONTROL

This terminal is used when operating and controlling the monitor externally (by RS-232C).

JREMOTE IN

Connect the remote cable* to the remote control’s remote jack to obtain wired remote control.

KREMOTE OUT

Connect the remote cable* to the REMOTE IN jack of the other display monitor to obtain wired remote control.

* The 1/8 Stereo Mini cable must be purchased separately.

Information

•For Y/CB/Cr, connect to the DVD1 or DVD2 terminals.

•For SCART, this unit provides three ways to connect: ·SCART1: Connect R/G/B to the DVD2 terminals

and composite sync. to the HD terminal. ·SCART2: Connect R/G/B to the DVD2 terminals

and composite sync. to the VIDEO1 terminal. ·SCART3: Connect R/G/B + composite sync. to the

RGB1 terminal.

GRGB1 (mini D-Sub 15pin)

Connect an analog RGB signal from a computer, etc.

here. This input can be used for Input or Output. (see

page E-5)E-8Downloaded From TV-Manual.com Manuals

4-12

Image 12

Contents PlasmaSync Plasma Monitor HD/DVD/DTV input signals supported on this system SignalsTable of Signals Supported Supported resolutionImportant Information English Deutsch Français Español Italiano Precautions Important InformationContents Installation Ventilation Requirements for enclosure mountingVideo signal RGB/DVD/HD signal Creating a video wallCable Management CablesHow to use the remote control Battery Installation and ReplacementUsing the wired remote control mode Handling the remote controlPart Names and Function Front ViewRear View/ Terminal Board Remote Control Basic Operations When viewing videos or digital video discs Wide OperationsWhen Picture Size is set to OFF Supported resolution Picture Size setting TrueOperations in the Side-by-side mode Split Screen OperationsShowing a couple of pictures on the screen at the same time Operations in the Picture-in-picture mode Selecting the input signals to be displayedAdjusting the OSM controls Zooming up pictures Advanced menu mode Menu OperationsReset Menu Tree Restoring the factory default settings LanguagePicture Settings Menu Adjusting the pictureSetting the color temperature Reducing noise in the pictureAdjusting the color to the desired level Making the Low Tone adjustmentsAdjusting the colors Changing the Gamma CurveAudio Settings Menu Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture AdjOption1 Settings Menu Setting the on-screen menuSetting the BNC connectors Setting the RGB1 connectorSetting the Input Skip Resetting to the default valuesSetting high definition images to the suitable screen size Option2 Settings Menu Setting the power management for computer imagesSetting the picture to suit the movie POWER/STANDBY indicatorOrbiter settings Inverse SettingsOrbiter Function settings Setting the timeSetting the gray level for the sides of the screen Setting the screen size for S1/S2 video inputSoft Focus settings Gray Level settingsOption3 Settings Menu Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal Using the timerProgram Timer settings To reset the programTo reset the data Special characters in the Program Timer screenSetting the power on mode Enabling/disabling remote control wireless transmissionLoop Out setting Enabling/disabling the front panel controlsID number setting Video Wall settingDISP. Mode settings Auto ID settingsImage Adjust settings On Delay settingsPLE Link settings Repeat Timer settingsRepeat Timer PLE LinkOption4 Settings Menu Erasing the sub screen image when there isNo input signal Displaying still images in the sub screenAdvanced OSM Settings Menu Language Settings MenuSwitching the input source quickly Setting the menu modeColor System Settings Menu Setting the video signal formatExample Setting the color system to 3.58 Ntsc Video signal formatsExternal Control Pin AssignmentsTroubleshooting Symptom Checks Remedy