Pioneer VSA-AX10 Switching ANALOG/DIGITAL Signal Input, Playback of 96kHz 24 bit sound formats

Page 48

Basic Operation

Switching ANALOG/DIGITAL Signal Input

This button selects the type of input signal, ANALOG, DIGITAL or 2 RF, sent to the amplifier. You need to take special care to switch to the appropriate input when necessary. For example, the switch would have to be on DIGITAL to hear DOLBY DIGITAL, MPEG or DTS surround sound material but it would have to be on analog to record from the ANALOG out jacks on the amplifier. The default setting is AUTO which chooses digital over analog when both are available but goes with whatever is available if it is the only choice.

Amplifier

MAIN

SUB

SUB

TONE

BASS/

 

 

 

TREBLE

 

 

 

 

 

 

 

 

 

EFFECT/

 

DISPLAY

VIDEO

CH SEL.

 

DIMMER

SELECT

 

 

 

STATUS

SPEAKER

LOUDNESS

INPUT

 

 

A/B

 

ATT.

1

SYSTEM

 

TAPE 2

SIGNAL

SETUP

 

MONITOR

SELECT

1Press the SIGNAL SELECT button on

the SUB screen.

Each press switches the signal in the order below:

AUTO ANALOG DIGITAL 2RF

1

memo

In the AUTO setting, amplifier chooses the signal, based on availability, in the following order of priority:

2 RF, DIGITAL, ANALOG.

When DIGITAL signal is selected, 2 DIGITAL lights when a Dolby Digital signal is input; DTS lights when a DTS signal is input.

If no digital inputs (see p.80) are assigned, the SIGNAL SELECT will default to ANALOG.

Because the audio signal from a karaoke microphone and LDs are recorded with analog audio only, they are not output from the digital outputs. Set SIGNAL SELECT to ANALOG to listen to these formats.

When an LD with DTS is played back with the SIGNAL SELECT set in ANALOG, digital noise caused by playing back the DTS signal directly (with no decoding) is output. To prevent noise, you need to make digital connections (See p.24 & 25) and set SIGNAL SELECT to AUTO or DIGITAL.

Some DVD players don’t output DTS signals. For more details, refer to the instruction manual supplied with your DVD player.

This amplifier can only play back Dolby Digital, MPEG, PCM (32kHz, 44kHz, 48kHz, 88kHz and 96kHz sampling frequency), and DTS digital signal formats. If your source is not one of these select ANALOG for playback.

Make sure you connect your DVD/LD or LD players using the 2 RF jack. If your player has a 2 RF output this will ensure you can use all LDs. Refer to p.19.

Playback of 96kHz 24 bit sound formats

This amplifier is capable of playing back 96kHz/24bit sound formats (such as DTS 96/24 and PCM 96kHz (up to 24bit).

To Playback with the Best Sound Quality (all processing is done at 96 kHz).

For DTS 96/24 5.1 format, connect both center and surround left/right speakers, set LISTENING CH SELECT to AUTO or 5.1, choose STANDARD mode and turn off all sound functions. For 96kHz 2ch format (either DTS or PCM) choose STEREO mode and turn off sound functions. For both these playbacks, "96kHz" will appear in the amplifier's display. If it doesn't the processing is being done at 48kHz.

You can listen to DTS 96/24 soundtracks through this amplifier if your DVD player has a DTS output feature, even if it can't output 96kHz digital signals. For PCM 96kHz soundtracks, however, you won't be able to listen to them with digital connections if your DVD player can't output 96kHz digital signals. Also, if you set RE-EQ on you won't be able to get 96kHz processing.

Check the manual that came with your DVD player to confirm what it can output and for more information on

48 these formats.

En

Image 48
Contents VSA-AX10 Installing the Amplifier Operating Environment H045 EnFeatures Table of Contents Table of Contents Checking the Supplied Accessories Preparing the Remote ControlRemote Control Battery Alarm Before You StartRemote Control Cushions Operating range of remote control unitOpening the Front Panel Touch Pen & LockSetting Up the Remote Control Press the LCD Commander buttonPress the Touch Panel Adjustment button Remote Control Backlight Use LockQuick Start Guide Part1 Home Theater The BasicsHooking Up Your DVD Player & TV Digital ConnectionsDVD player Speaker Connections SpeakersSetting up the Main Unit Assigning the Digital InputsSpeaker terminals Auto Surround Sound Setup Switch on the amplifier and your TVQuick Start Guide Part2 Choose Exit with the 5∞ buttons Press EnterQuick Start Guide Part2 Check the speaker settings on OSDEnter Press the Listening CH Select button on the remote control Play a DVD then adjust the Master VolumePlaying a DVD with Surround Sound Personalizing Your SoundConnecting Your Equipment Connecting your TVConnecting Video Components Connecting a DVD, DVD/LD or LD playerDVD/LD player or LD player LD player onlyConnecting VCRs or DVRs Connecting a Video Component to the Front PanelConnecting Satellite TV SAT Components VideoConnecting Analog Audio Components RecorderAudio cords Cassette deck placement Components equipped withConnecting Digital Audio Components AudioDigital Input Default Settings Coaxial cords/Optical cablesCoaxial cord Connecting Speakers To 16 ΩSpeaker placement Placing Your SpeakersAC Power Cord AC Outlet switched 100 w maxRemote Control Displays & ControlsBasic Amplifier LCD Screens Amplifier Main ScreenAmplifier SUB Screen Shaped connectors Back PanelAC in Power Control IN/OUT terminal Speaker terminalsComponent video in terminals AC outletFront Panel Setup MIC jack Tone control buttons Tone buttonBASS/TREBLE button See p.55 Video Select button See p.58Display Setting Up for Surround Sound Channel Delay See p.41Speaker Systems See p.38-40 Channel Level See p.42-43Front default setting is Small Center default setting is SmallSurround default setting is Small Surround Back default setting is SmallUse the 5∞ buttons to select Speaker system setting ˜∞ buttonsUse the 5∞ buttons to select Return and press Enter THXChannel Delay should be When done select Return with ∞ buttons and press EnterIf you want to change a setting before proceeding Selected. If it isn’t use the 5∞ buttonsChannel Level channel balance Acoustic Calibration EQ Acoustic CAL EQ should be selectedIf it isn’t use the 5∞ buttons to select ALL CH ADJ Check the Auto Settings Basic Operation Stereo and Multichannel PlaybackSTANDBY/ON StandardAdjust the volume by using Master Volume buttons onRemote control. On the front panel Use the Master Volume dialSwitching ANALOG/DIGITAL Signal Input Press the Signal Select button on SUB screenPlayback of 96kHz 24 bit sound formats Listening Modes Stereo modesStandard modes Home THX modes TX Technical extensionAdvanced Cinema modes THX ULTRA2 CinemaAdjusting the Effect of Advanced Listening Modes Advanced Concert modesListening with Acoustic Calibration EQ Reducing Noise During Playback Digital NR FunctionListening in Midnight Mode Listening in Loudness ModeRemote control’s AMP Main screen Each press switches Midnight mode on or offAdjusting Bass and Treble Tone Control TrebleRemote control’s AMP Main screen DVD Audio/MULTI Channel in PlaybackPress Multi CH in button on Use the button to cycle throughDual Mono Setting and playback Input AttenuatorTape 2 Monitor Using the Headphones Plug headphones into the headphoneVideo Select Jack on the front of the amplifierAdjusting the Brightness of the Display Status DisplayPress AMP. Choose the SUB screen Press the Status button Remote Control of Other Components Setting Up the Remote Control to Control Other ComponentsChoose the button for example DVD/LD you want to assign toTo exit the process without inputting the commands Select the name of the company that Makes your componentPress the number 1 button To go back a screenPress the Remote Setup Press the Learning button If you want to cancel the Remote Setup modePress the function button for Component you want to control Locking the Settings Remote SetupRemote Setup screens hold Using the Remote Control with Other Components DVD and TV operationsDigital TV screen Number buttonsSetting up the Direct Function To leave the Direct Function mode press the Back buttonUsing Other Functions Recording from Audio/Video ComponentsSpeaker System B Setup Bi-wiring your speakersStereo playback in another room Bi-amping the front speakersSwitching A/B Speaker System Connecting Additional Amplifiers Front channel amplifierPre Out Power Setup Pioneer SR System Operating other Pioneer components PioneerMulti Operations When done press Setup OK to input Information DVDMulti OperationSelect the command number you System offWant the process to start with. Course its logical to start with 1 soPower off commands you want to Repeat steps 4-6 to program aSequence of up to five stop or InputEditing Remote Control Screen Names Item Memo Press the Setup OK button whenUse the Back button to return to Editing Buttons Names KEY Label Edit mode ~For TEXT~~For GRAPHICs~ Resetting the Main Unit Resetting the Remote ControlRelease the reset tab and then Tone +Advanced Setup Assigning the Digital InputAssigning the Component Video Inputs Expert Setup Press the SUB button on the amplifier screenDynamic Range Control p.85 Multi CH in Select p.86OSD On-screen Display Adjustment ˜∞˜2˜3˜ENTER buttonsCancel Bass Peak LevelDynamic Range Control Use the 5∞ buttons to select RETURN. Press Enter buttonUse the 5∞ buttons to select Output Mode you want Multi CH in SelectFunction Rename Repeat until you get the name As you want itFollow steps 1-4 on page 82, if necessary, to get to Starting point mentioned hereTHX Audio Setup THX Ultra2 Subwoofer SetupUse the 23 buttons to select on or OFFSurround Back Speaker Position Re-Equalization Techno Tidbits & Problem-solving DolbyDolby Digital Channel Channel analogChart Comparing Dolby Pro Logic and Dolby Pro Logic Mpeg AudioDolby Pro Logic Dolby Digital Surround EXDTS DTS-ESDTS Neo6 DTS 96/24Techno Tidbits & Problem-solving SBL Speaker Placement for a Complete THX Speaker System Speaker Placement for DVD-Audio etc. SourcesAudio Block Diagram Troubleshooting Center speakers SubwooferSurround back speakers No sound output from oneWhen playing an LD Signal Select is on 2 RFPlayback Over indicator is Noise is output When playing a DTS formatCome up when using Signal Select buttonDigital format indicator Digital format indicatorsRemote control Cannot be remote During playback of a 96kHzSource, the display doesnt Show 96kHzSpecifications TNGZF/01L00001