Pioneer VSA-AX10 Function Rename, Repeat until you get the name As you want it

Page 87

Advanced Setup

FUNCTION RENAME

Use the FUNCTION RENAME capability to rename the display on the amplifier and your OSD for different functions (DVD, etc.). For example, you could rename VCR1/DVR as "DVR-7000".

	Follow steps 1-4 on page 82, if necessary, to get to the
STANDBY/ON	starting point mentioned here.

ENTER

5˜∞˜2˜3˜ENTER buttons

1	3.Expert Setup

	[1. OSD Adjustment ]
	[2. Bass Peak Level]
	[3. D-Range Control]
	[4. Multi-Ch In Select]
	[	5. Function Rename				]
	[Return]
2	3.5. Function		Rename
		DVD/LD	[		DVD/LD		]
		DVD/LD	[		DVD/LD		]
		TV	[		TV		]
		SAT	[		SAT		]
3	3.5. Function		Rename
		VCR1/DVR [			VCR1/DVR		]

		VIDEO	[		VIDEO		]
		VCR1/DVR [ VCR1/DVR					]
		VCR2	[		VCR2		]
		VCR3	[		VCR3		]
4	3.5. Function			Rename
		VCR1/DVR [ DVR-7000						]

		VIDEO	[		VIDEO		]
		VCR1/DVR [			VCR1/DVR ]
		VCR2	[		VCR2		]
		VCR3	[		VCR3		]
6	3.5. Function		Rename
		CD	[		CD		]
		CD	[		CD		]
		CD-R	[ CD-R/TAPE1 ]
		TUNER	[		TUNER		]
		PHONO	[		PHONO		]

[Return]

1FUNCTION RENAME should be selected if it isn’t use the 5∞ buttons to select it. Press ENTER.

2Use the 5∞ buttons to select the name of the function (for example, “VCR1/DVR”) you want to change.

Press ENTER.

The functions are divided into three different on-screen displays so you may have to move through them to find the function you want to rename.

3Use the 2 3 buttons to move the cursor around and use the 5∞ buttons to enter a letter, number or

symbol.

The possible selections are shown below.

ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 0123456789 !”#$%&’()*+,–./:;<=>?@[ \ ]ˆ_{} (space)

4Repeat step 3 until you get the name

as you want it.

You can input up to ten characters.

5Press ENTER. The new function name is set.

6Repeat steps 2-5 to change other function names. Use the 5∞ buttons to select RETURN and press ENTER.

7To finish EXPERT SETUP use the 5∞ buttons to select RETURN and press ENTER. Then use the 5∞ buttons to select EXIT and press ENTER.

EXPERT

87

En

Image 87

Contents VSA-AX10 Operating Environment H045 En Installing the AmplifierFeatures Table of Contents Table of Contents Before You Start Checking the Supplied AccessoriesPreparing the Remote Control Remote Control Battery AlarmTouch Pen & Lock Remote Control CushionsOperating range of remote control unit Opening the Front PanelSetting Up the Remote Control Press the LCD Commander buttonPress the Touch Panel Adjustment button Use Lock Remote Control BacklightHome Theater The Basics Quick Start Guide Part1Hooking Up Your DVD Player & TV Digital ConnectionsDVD player Speakers Speaker ConnectionsSetting up the Main Unit Assigning the Digital InputsSpeaker terminals Choose Exit with the 5∞ buttons Press Enter Auto Surround Sound SetupSwitch on the amplifier and your TV Quick Start Guide Part2Quick Start Guide Part2 Check the speaker settings on OSDEnter Personalizing Your Sound Press the Listening CH Select button on the remote controlPlay a DVD then adjust the Master Volume Playing a DVD with Surround SoundConnecting your TV Connecting Your EquipmentLD player only Connecting Video ComponentsConnecting a DVD, DVD/LD or LD player DVD/LD player or LD playerConnecting a Video Component to the Front Panel Connecting VCRs or DVRsVideo Connecting Satellite TV SAT ComponentsConnecting Analog Audio Components RecorderAudio cords Components equipped with Cassette deck placementAudio Connecting Digital Audio ComponentsDigital Input Default Settings Coaxial cords/Optical cablesCoaxial cord To 16 Ω Connecting SpeakersPlacing Your Speakers Speaker placementAC Outlet switched 100 w max AC Power CordDisplays & Controls Remote ControlAmplifier Main Screen Basic Amplifier LCD ScreensAmplifier SUB Screen Back Panel Shaped connectorsAC outlet AC in PowerControl IN/OUT terminal Speaker terminals Component video in terminalsFront Panel Video Select button See p.58 Setup MIC jackTone control buttons Tone button BASS/TREBLE button See p.55Display Channel Level See p.42-43 Setting Up for Surround SoundChannel Delay See p.41 Speaker Systems See p.38-40Surround Back default setting is Small Front default setting is SmallCenter default setting is Small Surround default setting is Small˜∞ buttons Use the 5∞ buttons to select Speaker system settingTHX Use the 5∞ buttons to select Return and press EnterSelected. If it isn’t use the 5∞ buttons Channel Delay should beWhen done select Return with ∞ buttons and press Enter If you want to change a setting before proceedingChannel Level channel balance Acoustic Calibration EQ Acoustic CAL EQ should be selectedIf it isn’t use the 5∞ buttons to select ALL CH ADJ Check the Auto Settings Standard Basic OperationStereo and Multichannel Playback STANDBY/ONUse the Master Volume dial Adjust the volume by usingMaster Volume buttons on Remote control. On the front panelSwitching ANALOG/DIGITAL Signal Input Press the Signal Select button on SUB screenPlayback of 96kHz 24 bit sound formats Listening Modes Stereo modesStandard modes TX Technical extension Home THX modesTHX ULTRA2 Cinema Advanced Cinema modesAdvanced Concert modes Adjusting the Effect of Advanced Listening ModesReducing Noise During Playback Digital NR Function Listening with Acoustic Calibration EQEach press switches Midnight mode on or off Listening in Midnight ModeListening in Loudness Mode Remote control’s AMP Main screenTreble Adjusting Bass and Treble Tone ControlUse the button to cycle through Remote control’s AMP Main screenDVD Audio/MULTI Channel in Playback Press Multi CH in button onDual Mono Setting and playback Input AttenuatorTape 2 Monitor Jack on the front of the amplifier Using the HeadphonesPlug headphones into the headphone Video SelectAdjusting the Brightness of the Display Status DisplayPress AMP. Choose the SUB screen Press the Status button DVD/LD you want to assign to Remote Control of Other ComponentsSetting Up the Remote Control to Control Other Components Choose the button for exampleTo go back a screen To exit the process without inputting the commandsSelect the name of the company that Makes your component Press the number 1 buttonPress the Remote Setup Press the Learning button If you want to cancel the Remote Setup modePress the function button for Component you want to control Locking the Settings Remote SetupRemote Setup screens hold Number buttons Using the Remote Control with Other ComponentsDVD and TV operations Digital TV screenTo leave the Direct Function mode press the Back button Setting up the Direct FunctionRecording from Audio/Video Components Using Other FunctionsBi-amping the front speakers Speaker System B SetupBi-wiring your speakers Stereo playback in another roomSwitching A/B Speaker System Front channel amplifier Connecting Additional AmplifiersPre Out Power Setup Pioneer Pioneer SR System Operating other Pioneer componentsMulti Operations DVDMulti Operation When done press Setup OK to input InformationCourse its logical to start with 1 so Select the command number youSystem off Want the process to start with.Input Power off commands you want toRepeat steps 4-6 to program a Sequence of up to five stop orEditing Remote Control Screen Names Item Memo Press the Setup OK button whenUse the Back button to return to Editing Buttons Names KEY Label Edit mode ~For TEXT~~For GRAPHICs~ Tone + Resetting the Main UnitResetting the Remote Control Release the reset tab and thenAssigning the Digital Input Advanced SetupAssigning the Component Video Inputs Multi CH in Select p.86 Expert SetupPress the SUB button on the amplifier screen Dynamic Range Control p.85˜∞˜2˜3˜ENTER buttons OSD On-screen Display AdjustmentBass Peak Level CancelUse the 5∞ buttons to select RETURN. Press Enter button Dynamic Range ControlMulti CH in Select Use the 5∞ buttons to select Output Mode you wantStarting point mentioned here Function RenameRepeat until you get the name As you want it Follow steps 1-4 on page 82, if necessary, to get toOFF THX Audio SetupTHX Ultra2 Subwoofer Setup Use the 23 buttons to select on orSurround Back Speaker Position Re-Equalization Channel Channel analog Techno Tidbits & Problem-solvingDolby Dolby DigitalDolby Digital Surround EX Chart Comparing Dolby Pro Logic and Dolby Pro LogicMpeg Audio Dolby Pro LogicDTS 96/24 DTSDTS-ES DTS Neo6Techno Tidbits & Problem-solving SBL Speaker Placement for DVD-Audio etc. Sources Speaker Placement for a Complete THX Speaker SystemAudio Block Diagram Troubleshooting No sound output from one Center speakersSubwoofer Surround back speakersNoise is output When playing a DTS format When playing an LDSignal Select is on 2 RF Playback Over indicator isDigital format indicators Come up when usingSignal Select button Digital format indicatorShow 96kHz Remote control Cannot be remoteDuring playback of a 96kHz Source, the display doesntSpecifications TNGZF/01L00001