Pioneer VSA-AX10 Using Other Functions, Recording from Audio/Video Components

Page 66

Using Other Functions

Recording from Audio/Video Components

The following explanations show you how make a recording from one component to another connected to this amplifier. Note that an analog recorder (such as a VCR) cannot record from a source that is connected using only a digital connection. Likewise, a digital recorder (such as a CD-R) cannot record digitally from a component that is connected using only analog connections. In both of these cases, make sure that the digital component also has analog connections to the amplifier, and that the SIGNAL SELECT is set to ANALOG.

When recording from one digital component to another, bear in mind that the digital signal output from this amplifier mirrors the input from the source. So if the input is, say, Dolby Digital, the output will also be Dolby Digital. Before recording, make sure that the recorder is compatible with the source digital audio format.

See p.22 for more on analog audio connections and p.24-25 for digital audio connections.

memo • The amplifier's volume, channel level, balance, TONE, Digital NR, MIDNIGHT, LOUDNESS, ACOUSTIC CAL EQ and surround effects have no effect on the recorded signal.

•In some cases, digital recordings have copy guard protections and making a digital copy is not pos- sible. In this case you can only copy them in an analog manner.

•When the source is the connected to the MULTI CH IN jacks, only the front left/right channels can be recorded.

•Some video recordings are copy-protected; these sources cannot be recorded.

•When recording video, the source must be connected to the amplifier using the same type of video cord (composite, or S video) as you used to connect the recorder to the amplifier.

Functions that can be recorded

1

Select the source component. Set

 

SIGNAL SELECT according to the

 

source component's signal (ANALOG

 

or DIGITAL).

 

 

2

Start recording (tape deck, CD

AMP

DVD/LD

VCR1

/DVR

VCR2

VCR3

TV

Amplifier

TONE BASS/ ATREBLE

DISPLAY VIDEO DIMMER SELECT

STATUS SPEAKER A/B

SYSTEM

SETUP

MAIN SUB

EFFECT/

CH SEL.

LOUDNESS INPUT ATT.

TAPE 2

SIGNAL

MONITOR

SELECT

REMOTE

SETUP

CD

CD-R/

TAPE1

TUNER

VIDEO

SAT

TV

CONTROL

recorder, VCR, etc.)

3 Playback the source to be recorded.

Record monitor (TAPE 2 MONITOR)

1 (if necessary)

If you connect a cassette deck with a record monitor function to the TAPE 2 MONITOR jacks, you can listen to the sound of an analog recording as it is being recorded.

Press TAPE 2 MONITOR to switch between the sound of the recording (TAPE 2 indicator on) and the sound of the source component (TAPE 2 indicator off).

• To record the TAPE 2 MONITOR signal to a recorder

memo connected to the CD-R/TAPE 1 inputs, select any input except CD-R/TAPE 1 and switch the TAPE 2 MONITOR on.

66

En

Page 65 Page 67
Image 66
Page 65 Page 67
Contents VSA-AX10 Installing the Amplifier Operating Environment H045 EnFeatures Table of Contents Table of Contents Remote Control Battery Alarm Checking the Supplied AccessoriesPreparing the Remote Control Before You StartOpening the Front Panel Remote Control CushionsOperating range of remote control unit Touch Pen & LockSetting Up the Remote Control Press the LCD Commander buttonPress the Touch Panel Adjustment button Remote Control Backlight Use LockQuick Start Guide Part1 Home Theater The BasicsHooking Up Your DVD Player & TV Digital ConnectionsDVD player Speaker Connections SpeakersSetting up the Main Unit Assigning the Digital InputsSpeaker terminals Quick Start Guide Part2 Auto Surround Sound SetupSwitch on the amplifier and your TV Choose Exit with the 5∞ buttons Press EnterQuick Start Guide Part2 Check the speaker settings on OSDEnter Playing a DVD with Surround Sound Press the Listening CH Select button on the remote controlPlay a DVD then adjust the Master Volume Personalizing Your SoundConnecting Your Equipment Connecting your TVDVD/LD player or LD player Connecting Video ComponentsConnecting a DVD, DVD/LD or LD player LD player onlyConnecting VCRs or DVRs Connecting a Video Component to the Front PanelConnecting Satellite TV SAT Components VideoConnecting Analog Audio Components RecorderAudio cords Cassette deck placement Components equipped withConnecting Digital Audio Components AudioDigital Input Default Settings Coaxial cords/Optical cablesCoaxial cord Connecting Speakers To 16 ΩSpeaker placement Placing Your SpeakersAC Power Cord AC Outlet switched 100 w maxRemote Control Displays & ControlsBasic Amplifier LCD Screens Amplifier Main ScreenAmplifier SUB Screen Shaped connectors Back PanelComponent video in terminals AC in PowerControl IN/OUT terminal Speaker terminals AC outletFront Panel BASS/TREBLE button See p.55 Setup MIC jackTone control buttons Tone button Video Select button See p.58Display Speaker Systems See p.38-40 Setting Up for Surround SoundChannel Delay See p.41 Channel Level See p.42-43Surround default setting is Small Front default setting is SmallCenter default setting is Small Surround Back default setting is SmallUse the 5∞ buttons to select Speaker system setting ˜∞ buttonsUse the 5∞ buttons to select Return and press Enter THXIf you want to change a setting before proceeding Channel Delay should beWhen done select Return with ∞ buttons and press Enter Selected. If it isn’t use the 5∞ buttonsChannel Level channel balance Acoustic Calibration EQ Acoustic CAL EQ should be selectedIf it isn’t use the 5∞ buttons to select ALL CH ADJ Check the Auto Settings STANDBY/ON Basic OperationStereo and Multichannel Playback StandardRemote control. On the front panel Adjust the volume by usingMaster Volume buttons on Use the Master Volume dialSwitching ANALOG/DIGITAL Signal Input Press the Signal Select button on SUB screenPlayback of 96kHz 24 bit sound formats Listening Modes Stereo modesStandard modes Home THX modes TX Technical extensionAdvanced Cinema modes THX ULTRA2 CinemaAdjusting the Effect of Advanced Listening Modes Advanced Concert modesListening with Acoustic Calibration EQ Reducing Noise During Playback Digital NR FunctionRemote control’s AMP Main screen Listening in Midnight ModeListening in Loudness Mode Each press switches Midnight mode on or offAdjusting Bass and Treble Tone Control TreblePress Multi CH in button on Remote control’s AMP Main screenDVD Audio/MULTI Channel in Playback Use the button to cycle throughDual Mono Setting and playback Input AttenuatorTape 2 Monitor Video Select Using the HeadphonesPlug headphones into the headphone Jack on the front of the amplifierAdjusting the Brightness of the Display Status DisplayPress AMP. Choose the SUB screen Press the Status button Choose the button for example Remote Control of Other ComponentsSetting Up the Remote Control to Control Other Components DVD/LD you want to assign toPress the number 1 button To exit the process without inputting the commandsSelect the name of the company that Makes your component To go back a screenPress the Remote Setup Press the Learning button If you want to cancel the Remote Setup modePress the function button for Component you want to control Locking the Settings Remote SetupRemote Setup screens hold Digital TV screen Using the Remote Control with Other ComponentsDVD and TV operations Number buttonsSetting up the Direct Function To leave the Direct Function mode press the Back buttonUsing Other Functions Recording from Audio/Video ComponentsStereo playback in another room Speaker System B SetupBi-wiring your speakers Bi-amping the front speakersSwitching A/B Speaker System Connecting Additional Amplifiers Front channel amplifierPre Out Power Setup Pioneer SR System Operating other Pioneer components PioneerMulti Operations When done press Setup OK to input Information DVDMulti OperationWant the process to start with. Select the command number youSystem off Course its logical to start with 1 soSequence of up to five stop or Power off commands you want toRepeat steps 4-6 to program a InputEditing Remote Control Screen Names Item Memo Press the Setup OK button whenUse the Back button to return to Editing Buttons Names KEY Label Edit mode ~For TEXT~~For GRAPHICs~ Release the reset tab and then Resetting the Main UnitResetting the Remote Control Tone +Advanced Setup Assigning the Digital InputAssigning the Component Video Inputs Dynamic Range Control p.85 Expert SetupPress the SUB button on the amplifier screen Multi CH in Select p.86OSD On-screen Display Adjustment ˜∞˜2˜3˜ENTER buttonsCancel Bass Peak LevelDynamic Range Control Use the 5∞ buttons to select RETURN. Press Enter buttonUse the 5∞ buttons to select Output Mode you want Multi CH in SelectFollow steps 1-4 on page 82, if necessary, to get to Function RenameRepeat until you get the name As you want it Starting point mentioned hereUse the 23 buttons to select on or THX Audio SetupTHX Ultra2 Subwoofer Setup OFFSurround Back Speaker Position Re-Equalization Dolby Digital Techno Tidbits & Problem-solvingDolby Channel Channel analogDolby Pro Logic Chart Comparing Dolby Pro Logic and Dolby Pro LogicMpeg Audio Dolby Digital Surround EXDTS Neo6 DTSDTS-ES DTS 96/24Techno Tidbits & Problem-solving SBL Speaker Placement for a Complete THX Speaker System Speaker Placement for DVD-Audio etc. SourcesAudio Block Diagram Troubleshooting Surround back speakers Center speakersSubwoofer No sound output from onePlayback Over indicator is When playing an LDSignal Select is on 2 RF Noise is output When playing a DTS formatDigital format indicator Come up when usingSignal Select button Digital format indicatorsSource, the display doesnt Remote control Cannot be remoteDuring playback of a 96kHz Show 96kHzSpecifications TNGZF/01L00001
Top Page Image Contents