Pioneer VSA-AX10 operating instructions Assigning the Component Video Inputs

Page 81

Advanced Setup

Assigning the Component Video Inputs

If you used component video cords (and only if you did so) to connect any equipment you must tell the amplifier which device is hooked up with this special kind of cable. If you did not use component video cord (which is a specialized cord that separates the video signal into two color spectrums and a light spectrum for transmission) then you don't need to worry about the procedure below. The default settings for the component video inputs are as follows: 1= off; 2= off; 3= off.

1

AMP

DVD/LD

VCR1

/DVR

VCR2

VCR3

3 TV

				2
Amplifier		MAIN	SUB	SETUP
				REMOTE
TONE	BASS/			CD
TONE	ATREBLE
	ATREBLE			CD-R/
				CD-R/
		EFFECT/		TAPE1
		EFFECT/
DISPLAY	VIDEO	CH SEL.		TUNER
DIMMER	SELECT
	SPEAKER		INPUT	VIDEO
STATUS	SPEAKER	LOUDNESS	INPUT
	A/B		ATT.	SAT
SYSTEM		TAPE 2	SIGNAL	TV
SETUP		MONITOR	SELECT	CONTROL

1	Turn on the amplifier and your TV,
	press the AMP on the remote
	control.

2	Press the SUB button on the remote
	control.

3	Press the SYSTEM SETUP button.


4	System Setup
	System Setup
	[ Auto Surround Setup ]
	[				]
	[	1. Input Assign			]
	[2. Surround Setup]
	[3. Expert Setup]
	[4. THX Audio Setup]
	[Exit]
5	1.Input Assign
	[ 1.Digital-In Select ]
	[		2.C'nent VideoIn				]
	[Return]
6	1.2. C' nent Video						In
		C' nent-In1						]
		C' nent-In1		DVD/LD[				]
		C' nent-In2		[		OFF		]
		C' nent-In3		[		OFF		]

[Return]

4	Looking at the on-screen display on
	your TV, use the 5∞ buttons to
	select INPUT ASSIGN. Press the
	ENTER button.

5	Use the 5∞ buttons to select
	C'NENT VIDEO IN. Press the ENTER
	button.

6	Use the 5∞ buttons to move
	through the different component
	video input settings and use the 2 3
	buttons to select the component
	that you hooked up to that

component video in.

If you're not sure which component is connected to which component video in, look on the back of the amplifier and check the cables you connected.

7	1.2. C' nent Video In
	C' nent-In1	[ DVD/LD ]
	C' nent-In2	[ VCR1	]
	C' nent-In3	[ OFF	]

[Return]

memo

If you connect the TV monitor with compo- nent video cord, and the DVD player with composite or S video cord then you should set that terminal to off.

7When you're finished use the 5∞ buttons to select RETURN and press

ENTER.

You will leave the "Assigning the Component Video Inputs" mode.

8Use the 5∞ buttons to select

RETURN and press ENTER, again. Then, use the 5∞ buttons to select

EXIT and press ENTER.

EXPERT

81

En

Image 81

Contents VSA-AX10 Operating Environment H045 En Installing the AmplifierFeatures Table of Contents Table of Contents Preparing the Remote Control Checking the Supplied AccessoriesRemote Control Battery Alarm Before You StartOperating range of remote control unit Remote Control CushionsOpening the Front Panel Touch Pen & LockSetting Up the Remote Control Press the LCD Commander buttonPress the Touch Panel Adjustment button Use Lock Remote Control BacklightHome Theater The Basics Quick Start Guide Part1Hooking Up Your DVD Player & TV Digital ConnectionsDVD player Speakers Speaker ConnectionsSetting up the Main Unit Assigning the Digital InputsSpeaker terminals Switch on the amplifier and your TV Auto Surround Sound SetupQuick Start Guide Part2 Choose Exit with the 5∞ buttons Press EnterQuick Start Guide Part2 Check the speaker settings on OSDEnter Play a DVD then adjust the Master Volume Press the Listening CH Select button on the remote controlPlaying a DVD with Surround Sound Personalizing Your SoundConnecting your TV Connecting Your EquipmentConnecting a DVD, DVD/LD or LD player Connecting Video ComponentsDVD/LD player or LD player LD player onlyConnecting a Video Component to the Front Panel Connecting VCRs or DVRsVideo Connecting Satellite TV SAT ComponentsConnecting Analog Audio Components RecorderAudio cords Components equipped with Cassette deck placementAudio Connecting Digital Audio ComponentsDigital Input Default Settings Coaxial cords/Optical cablesCoaxial cord To 16 Ω Connecting SpeakersPlacing Your Speakers Speaker placementAC Outlet switched 100 w max AC Power CordDisplays & Controls Remote ControlAmplifier Main Screen Basic Amplifier LCD ScreensAmplifier SUB Screen Back Panel Shaped connectorsControl IN/OUT terminal Speaker terminals AC in PowerComponent video in terminals AC outletFront Panel Tone control buttons Tone button Setup MIC jackBASS/TREBLE button See p.55 Video Select button See p.58Display Channel Delay See p.41 Setting Up for Surround SoundSpeaker Systems See p.38-40 Channel Level See p.42-43Center default setting is Small Front default setting is SmallSurround default setting is Small Surround Back default setting is Small˜∞ buttons Use the 5∞ buttons to select Speaker system settingTHX Use the 5∞ buttons to select Return and press EnterWhen done select Return with ∞ buttons and press Enter Channel Delay should beIf you want to change a setting before proceeding Selected. If it isn’t use the 5∞ buttonsChannel Level channel balance Acoustic Calibration EQ Acoustic CAL EQ should be selectedIf it isn’t use the 5∞ buttons to select ALL CH ADJ Check the Auto Settings Stereo and Multichannel Playback Basic OperationSTANDBY/ON StandardMaster Volume buttons on Adjust the volume by usingRemote control. On the front panel Use the Master Volume dialSwitching ANALOG/DIGITAL Signal Input Press the Signal Select button on SUB screenPlayback of 96kHz 24 bit sound formats Listening Modes Stereo modesStandard modes TX Technical extension Home THX modesTHX ULTRA2 Cinema Advanced Cinema modesAdvanced Concert modes Adjusting the Effect of Advanced Listening ModesReducing Noise During Playback Digital NR Function Listening with Acoustic Calibration EQListening in Loudness Mode Listening in Midnight ModeRemote control’s AMP Main screen Each press switches Midnight mode on or offTreble Adjusting Bass and Treble Tone ControlDVD Audio/MULTI Channel in Playback Remote control’s AMP Main screenPress Multi CH in button on Use the button to cycle throughDual Mono Setting and playback Input AttenuatorTape 2 Monitor Plug headphones into the headphone Using the HeadphonesVideo Select Jack on the front of the amplifierAdjusting the Brightness of the Display Status DisplayPress AMP. Choose the SUB screen Press the Status button Setting Up the Remote Control to Control Other Components Remote Control of Other ComponentsChoose the button for example DVD/LD you want to assign toSelect the name of the company that Makes your component To exit the process without inputting the commandsPress the number 1 button To go back a screenPress the Remote Setup Press the Learning button If you want to cancel the Remote Setup modePress the function button for Component you want to control Locking the Settings Remote SetupRemote Setup screens hold DVD and TV operations Using the Remote Control with Other ComponentsDigital TV screen Number buttonsTo leave the Direct Function mode press the Back button Setting up the Direct FunctionRecording from Audio/Video Components Using Other FunctionsBi-wiring your speakers Speaker System B SetupStereo playback in another room Bi-amping the front speakersSwitching A/B Speaker System Front channel amplifier Connecting Additional AmplifiersPre Out Power Setup Pioneer Pioneer SR System Operating other Pioneer componentsMulti Operations DVDMulti Operation When done press Setup OK to input InformationSystem off Select the command number youWant the process to start with. Course its logical to start with 1 soRepeat steps 4-6 to program a Power off commands you want toSequence of up to five stop or InputEditing Remote Control Screen Names Item Memo Press the Setup OK button whenUse the Back button to return to Editing Buttons Names KEY Label Edit mode ~For TEXT~~For GRAPHICs~ Resetting the Remote Control Resetting the Main UnitRelease the reset tab and then Tone +Assigning the Digital Input Advanced SetupAssigning the Component Video Inputs Press the SUB button on the amplifier screen Expert SetupDynamic Range Control p.85 Multi CH in Select p.86˜∞˜2˜3˜ENTER buttons OSD On-screen Display AdjustmentBass Peak Level CancelUse the 5∞ buttons to select RETURN. Press Enter button Dynamic Range ControlMulti CH in Select Use the 5∞ buttons to select Output Mode you wantRepeat until you get the name As you want it Function RenameFollow steps 1-4 on page 82, if necessary, to get to Starting point mentioned hereTHX Ultra2 Subwoofer Setup THX Audio SetupUse the 23 buttons to select on or OFFSurround Back Speaker Position Re-Equalization Dolby Techno Tidbits & Problem-solvingDolby Digital Channel Channel analogMpeg Audio Chart Comparing Dolby Pro Logic and Dolby Pro LogicDolby Pro Logic Dolby Digital Surround EXDTS-ES DTSDTS Neo6 DTS 96/24Techno Tidbits & Problem-solving SBL Speaker Placement for DVD-Audio etc. Sources Speaker Placement for a Complete THX Speaker SystemAudio Block Diagram Troubleshooting Subwoofer Center speakersSurround back speakers No sound output from oneSignal Select is on 2 RF When playing an LDPlayback Over indicator is Noise is output When playing a DTS formatSignal Select button Come up when usingDigital format indicator Digital format indicatorsDuring playback of a 96kHz Remote control Cannot be remoteSource, the display doesnt Show 96kHzSpecifications TNGZF/01L00001