Pioneer PRS-D4200F owner manual Installation, To prevent malfunction and/or injury

Page 15

Installation

CAUTION

• Do not install in:

—Places where it could injure the driver or pas- sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

such as on the floor in front of the driver’s seat.

•Make sure that wires are not caught in the sliding mechanism of the seats, resulting in a short-cir- cuit.

•Confirm that no parts are behind the panel when drilling a hole for installation of the amplifier. Protect all cables and important equipment such as fuel lines, brake lines and electrical wiring from damage.

•Install tapping screws in such a way that the screw tip does not touch any wire. This is impor- tant to prevent wires from being cut by vibration of the car, which can result in fire.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•To ensure proper installation, use the supplied parts in the manner specified. If any parts other than the supplied ones are used, they may damage internal parts of the amplifier, or they may become loose causing the amplifier to shut down.

•Never replace the fuse with one of greater value or rating than the original fuse. Use of an improp- er fuse could result in overheating and smoke and could cause damage to the product and injury including burns.

CAUTION:

To prevent malfunction and/or injury

•To ensure proper heat dissipation of the amplifier, be sure of the following during installation.

—Allow adequate space above the amplifier for proper ventilation.

—Do not cover the amplifier with a floor mat or carpet.

•DO NOT allow amplifier to come into contact with liquids due to, for example, the location where the amplifier is installed. Electrical shock could result. Also, amplifier and speaker damage, smoke, and overheating could result from contact with liquids. In addition, the amplifier surface and the surface of any attached speakers could become hot to the touch and minor burns could result.

•Do not install the amplifier on unstable places such as the spare tire board.

•The best location for installation differs with the car model and installation location. Secure the amplifier at a sufficiently rigid location.

•Make temporary connections first and check that the amplifier and the system operate properly.

•After installing the amplifier, confirm that the spare tire, jack and tools can be easily removed.

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS êìëëäàâ

14

Page 14 Page 16
Image 15
Page 14 Page 16
Contents PRS-D4200F Contents S.A Before Using This ProductAfter-sales service for Pioneer products Information to UserVisit us at the following site Visit our websiteEnglish Español Deutsch Français Italiano Nederlands êìëëäàâ Cut Off Frequency Control Setting the UnitPower Indicator BFC Beat Frequency Control SwitchGain Control LPF Low-Pass Filter/HPF High-Pass Filter Select SwitchInput Select Switch Input SwitchSetting the Gain properly Signal waveform when outputting at highGain Control of This Unit Connecting the Unit Speaker Channel Speaker Type PowerTo prevent damage and/or injury RCA input jack a Fuse 30 a ⋅ Speaker output terminal Connection DiagramBattery Wire and Ground Wire Size Connecting the Power TerminalConnecting the Speaker Output Terminals Using the Speaker InputConnections when using the speaker input Connecting the Speakers and Input Wires Four-channelThree-channel Two-channel Mono Two-channel StereoTo prevent malfunction and/or injury InstallationReplacing the top cover Example of installation on the floor mat or on the chassisAverage current drawn SpecificationsRaccordement des bornes de sortie vers Interrupteur BFC Commande de fréquenceTable des matières Sélecteur LPF Filtre passe-basCanada Service après-vente pour un produit PioneerAvant d’utiliser cet appareil Etats-UnisVisitez notre site Web PrécautionPage Couvercle supérieur Commande de la fréquence de coupureRéglage de l’appareil Témoin d’alimentationSélecteur d’entrée Commande du gainSélecteur LPF Filtre passe-bas/HPF Filtre passe-haut Commutateur de sélection d’entréeRéglage correct du gain Commande du gain de cet appareilRaccordement de l’appareil Pour éviter toute anomalie ou blessureVoie de sortie Type de haut-parleur Puissance Schéma de raccordement Section de câble de la batterie et câble de masse Raccordement de la borne d’alimentationRemarque Utilisation de l’entrée de haut-parleurRaccordement des bornes de sortie vers les haut-parleurs Connexion lors de l’utilisation de l’entrée de haut-parleurRaccordement des haut-parleurs et des câbles Quatre voiesTrois voies Deux voies mono Deux voies stéréoPour éviter toute anomalie de fonctionnement ou blessure ’installez pas l’appareilRemise en place du couvercle supérieur Exemple d’installation sur le tapis de sol ou sur le châssisConsommation moyenne de courant Caractéristiques techniquesContenido Conexión de los altavoces y cablesEjemplo de instalación en la alfombra del Antes de usar este producto Servicio posventa para productos PioneerEE.UU Visite nuestro sitio Web PrecaucionAdvertencia Interruptor BFC Control de la frecuencia de batido Ajuste de esta unidadCubierta superior Control de frecuencia de corteControl de ganancia Interruptor de selección de entradaInterruptor de entrada Control de ganancia de esta unidad Configuración apropiada de la gananciaConexión de la unidad Para evitar daños y/o lesionesTipo de altavoz Alimentación Fusible 30 a ⋅ Diagrama de conexiónSalida externa De entrada RCA BConexiones de terminales sin soldadura Conexión del terminal de alimentaciónTamaño del cable de batería y cable de puesta a tierra Nota Conexión del terminal de salida de altavozUso de la entrada de altavoz Conexiones cuando se utiliza la entrada de altavozToma de conector De entrada RCA B Conexión de los altavoces y cables de entradaCuatro canales Tres canalesDos canales estéreo Dos canales monoDesde el sistema estereofónico del coche salida RCA Para evitar fallas de funcionamiento y/o lesiones InstalaciónApriete el tornillo con una llave hexagonal de 4 mm Recolocación de la cubierta superiorConsumo de corriente promedio EspecificacionesÅ„ÛÓ 1-óÓÏÂ, å„ÛÓ-ÍÛ, íÓÍËÓ 153-8654, üÔÓÌËfl ÄÓÔÓ‡ˆËfl è‡ÈÓÌË

PRS-D4200F specifications

The Pioneer PRS-D4200F is an advanced 4-channel amplifier designed for car audio enthusiasts who seek high-quality sound and robust performance. Known for its compact yet powerful design, the PRS-D4200F is engineered to enhance the audio experience in any vehicle.

One of the standout features of the PRS-D4200F is its impressive power output. With a maximum output of 1,600 watts, this amplifier ensures that your audio system can produce loud, clear sound without distortion, even at higher volume levels. The RMS power rating of 50 watts per channel at 4 ohms and 100 watts per channel at 2 ohms allows for great flexibility when matching it with various speaker systems.

The PRS-D4200F utilizes Class D amplification technology, which is designed for high efficiency. This means that the amplifier produces less heat compared to traditional Class A/B amps, allowing it to deliver more power without the risk of overheating, making it ideal for long listening sessions on the road.

The amplifier features a low-pass filter and high-pass filter, providing users with the ability to tailor the sound to their preference easily. This adjustability ensures that users can optimize their audio for different speaker setups, whether they are focusing on throaty bass or crystal-clear highs. Additionally, the inclusion of a bass boost feature allows for enhanced low-frequency performance, providing an extra punch to bass-heavy music.

Pioneer has equipped the PRS-D4200F with a durable construction, ensuring that it can withstand the rigors of vehicle installation. The compact design allows it to fit into tighter spaces, making it easier to integrate into different car models without sacrificing performance. The amplifier’s sleek look also adds a modern touch to any audio setup.

Another key feature of the PRS-D4200F is its protection circuitry. This technology helps prevent damage due to short circuits, overheating, and other issues, ensuring long-lasting reliability. The amplifier also includes a low-impedance capability, which means it can work with a wider variety of speakers, further enhancing its versatility.

In conclusion, the Pioneer PRS-D4200F stands out as an excellent choice for those looking to upgrade their vehicle’s audio system. With its powerful output, efficient design, and customizable sound options, it meets the needs of both casual listeners and serious audiophiles alike. Whether you are an urban commuter or a road trip enthusiast, the PRS-D4200F is engineered to elevate your audio experience.
Top Page Image Contents