Motorola IC-T81E Adjustment Procedures, Preparation, ‘ Required Test Equipment, Connection

Page 15

SECTION 5 ADJUSTMENT PROCEDURES

5-1 PREPARATION

‘REQUIRED TEST EQUIPMENT

	EQUIPMENT	GRADE AND RANGE		EQUIPMENT	GRADE AND RANGE

	DC power supply	Output voltage	: 13.5 V DC	DC voltmeter	Input impedance	: 50 kΩ /V DC or better
		Current capacity	: 3 A or more
				Audio generator	Frequency range	: 300–3000 Hz


		Measuring range	: 1–10 W		Measuring range	: 1–500 mV

	RF power meter	Frequency range	: 28–1500 MHz
					Frequency range	: 28–1300 MHz
	(terminated type)	Impedance	: 50 Ω	Standard signal
					Output level	: 0.1 µV–32 mV
		SWR	: Less than 1.2 : 1	generator (SSG)
						(–127 to –17 dBm)

		Frequency range	: 0.1–1500 MHz
	Frequency counter				Frequency range	: DC–20 MHz
		Frequency accuracy : ±1 ppm or better		Oscilloscope
					Measuring range	: 0.01–20 V
		Sensitivity	: 100 mV or better

				AC millivoltmeter	Measuring range	: 10 mV–10 V
	FM deviation meter	Frequency range	: 30–1500 MHz

		Measuring range	: 0 to ±10 kHz	Attenuator	Power attenuation	: 40 or 50 dB

‘ENTERING THE ADJUSTMENT MODE q Connect a 68 kΩ terminator to the [SP] jack.

w Push and hold the [SQL] key, and then turn power ON.

Note: The frequency of wide range appears at the display using this operation.

■CONNECTION

FM Deviation meter

Attenuator 40 dB or 50 dB

to the antenna connector

RF power meter 10 W/50 Ω

Frequency counter

Standard signal generator

to [SP] jack

JIG

+

68 kΩ

-

CAUTION:

DO NOT transmit while an SSG is connected to the antenna connector.

AD-92SMA

Optional SMA–BNC adaptor

1/8" (3.5 mm)

3-conductor plug

to [MIC] jack

Audio generator

AC millivoltmeter

Power supply 13.5 V / 3 A

5 - 1

Image 15

Contents Multiband FM Transceiver Sample Order IntroductionOrdering Parts Repair NotesTable of Contents Version 50 MHz 145 MHz 440 MHz 1200 MHz MHz RX only SpecificationsGeneral TransmitterWFM ReceiverBand WFMCPU Inside ViewsLogic Unit RF UnitLogic unit Disassembly InstructionsRemoving the Chassis Panel Removing the Shield Plate Removing the Logic Unit Removing the RF UnitDuplexer Circuit RF Unit Antenna Switching Circuits RF UnitCircuit Description Receiver Circuits7 1ST Mixer Circuit RF Unit Transmitter Circuits APC Control Circuit DRIVE/POWER Amplifier Circuits RF UnitAPC Circuits RF Unit MHz PAVCC Power Supply Circuits Voltage LinePLL Circuits Line DescriptionPin Port Description Number Name Port Allocations1 I/O Expander IC RF Unit IC2 2 I/O Expander IC RF Unit IC3CPU Logic Unit IC1 Connection Adjustment ProceduresPreparation ‘ Required Test EquipmentPLL Adjustment RF Unit TOP View 6MLV RF Unit Bottom ViewULV VLVVHF Receiver AdjustmentDial SensitivityLogic Unit TOP View 101 dBm MeterSSG Top Push and hold MHz bandSQL key Displayed frequencyPush and hold 445.000 MHz USA-1Transmitter Adjustment AUS, SEA DeviationHPF OFF LPF Dtmf=Surface mount Parts ListTrimmer Ceramic ECUE1H121JCQ Transistor UN911D TX Coil Eljnd R10J 0.1U Themistor Ceramic ECUE1H060CCQ Ceramic ECUE1H390JCQ VCO Board Ceramic ECUE1H120JCQ VCO Unit Mechanical Parts and DisassemblyAccessories Chassis PartsMP29 C SEMI-CONDUCTOR Information Transistor and FET’SDiodes Board Layouts Logic UnitTOP View GND Pset Ifin Bottom ViewIC1 IC3J4 to Logic unit J1 RF UnitIC6 L912MP1 IC3IC2 VLVCO3 VHF GND VHVCO3 UVCO3 Uhfout GND 12VCO3 GND VCO BoardJ302 to RF unit OUT 12VCOOUTQ354 Block Diagram ANT LPF HPF AMP Mode Xtal BPF PDA2, CK AMPTX/RX Frequency TX/RX BuffANT Buff HPF LPF YGR ResetMode Xtal Initial BPF MOD TX/RX FrequencyLogic Unit Section Voltage DiagramWFM NTCCF20124AH 473KCT TXC 2NDLOOscin Mixin Oscout GND Mixout REC VCC DET Ifin Rssi DEC Ifout Filout QuadCOM4 COM3 COM2 COM1 12VCO COM2 ResetCOM3 COM2 Reset Power Clonein VCC VIN Cpuhv1200M RF UnitVHF 400M400MHz 50M00M 1200MHzLOK GND2 GND1PLST1 IN1 ENB VCC2Icom America Inc Icom Inc 5566I-S