Standard Horizon Ff520 HOW can I SET Optimal Operating Parameters, What are Preset MODES?

Page 38

Figure 7.0b - The FF520 (III)

7.1HOW CAN I SET OPTIMAL OPERATING PARAMETERS.

Optimal operating parameters can be set accordingly with the intended use of the Fish Finder, to quickly get optimal operational parameters for fishing it is may be best to select the FISH preset from the Fish Finder Setup menu, while for cruising it is may be best to select the CRUISE preset.

7.2WHAT ARE PRESET MODES?

Preset modes are pre-defined settings of the Fish Finder operating parameters. You can use them to quickly set the Fish Finder in the most commonly used operating modes. These are:

·CRUISE: sets Fish Finder in full auto mode with the sensitivity settings (GAIN OFFSET,

NOISE level and STC) optimized for displaying the bottom while underway.

· FISH : sets the Fish Finder in full auto mode with the sensitivity setting optimized for fish finding.

7.3HOW CAN I RESTORE THE FISH FINDER DEFAULT OPERAT- ING PARAMETERS?

While the Fish Finder page is shown, press [MENU] and move the ShuttlePoint knob to Transducer Setup and press [ENTER]. Move the ShuttlePoint knob to Set Defaults and press [ENTER]. Press [CONFIRM] on the C175C/CP1000C/CPV350, or on the CP155C/ CP180/CP180i press [ENTER]. Note that this operation set all default settings, not only the working defaults.

7.4CAN I ALWAYS LEAVE THE FISH FINDER IN FULL AUTO/ (AUTO GAIN AND AUTO RANGE) MODE?

Yes, but note that the full auto mode suits the 90% of the cases, however in extreme situations the auto modes mail fail and thus it is necessary to switch to the Manual mode.

7.5WHAT ARE EXTREME SITUATIONS IN WHICH AUTO MODES MAY FAIL?

When the bottom is very deep, at high boat speed, when the bottom is very shallow (< 5 feet),

Page 40		FF520

Image 38

Contents FF520 FCC Compliance Statement Table of Contents Index Introduction General Information0 FF520 Packing List Replacement partPacking List Connections InstallationMounting the FF520 CP180/CP180i Connecting the GPS Chart Plotters to the FF520CP155C/CP1000C/CP180/CP180i/CPV350 connections to FF520 FF520CP175C connections to FF520 Optional ConnectionsCPV350 FF520 Tee Cable Nmea Output Alarm BuzzerLED Status Indicator Second temp sensorCP180/CP180i/CPV350 Power ConnectionsSelecting the FF520 CP155C/CP175C/CP1000C 0 Selecting the FF520 on CP180/CP180i/CPV350Fish Finder Understanding the Fish FinderFish Finder window Color BarOperating Frequency Understanding the Fish Finder displayScope FishesDisplaying the Fish Finder Menu selection for CP155C/CP175C/CP1000CSoft Keys for CP175C/CP1000C/CPV350 0a Menu selection for CP180/CP180i/CPV350Customizing the Fish Finder menu selection KEY Operation When Fish Finder page is Shown Customizing the Soft Keys for CP175C/CP1000C/CPV350Clear key Menu keyEnter key Zoom in and Zoom OUT keysShuttlepoint knob Controls on Chart page or Fish page in Chart/Fish dual modeMark key Focus Soft Key for CP175C/CP1000C/CPV350Frequency Soft Key System Update menuRange Soft Key Sensitivity Time Control STC Soft KeySystem Information page for CP180/CP180i/CPV350 Selection Fish Finder Setup MenuPresets FishRange Menu Gain ModeChart/Fish AutoGain Interference RejectionSensitivity Menu Display Setup Transducer Setup Keel OffsetSave Settings to User C-CARD AlarmsLoad Settings from User C-CARD Restore Current Preset Defaults Page Specifications FF520 SpecificationsFF520 Internal Connections FF520 Internal connectionsTransducer Mounting Power BoatsTransducer SailboatsTransom Transducer TypesLow Profile Thru-Hull Fairing BlockIn-hull Optional Transducer ID SensorsPage Tips of Operations 0a The FF520What are Extreme Situations in Which Auto Modes MAY FAIL? What are Preset MODES?HOW can I SET Optimal Operating Parameters What should I do if the Auto Modes FAIL? WHY do I Never see Fishes in the Range Between 0 to 2 FEET? HOW can I Reduce the Surface CLUTTER?Index 27, 30A N D a R D H O R I Z O N L I M I T E D W a R R a N T Y

Related manuals

Manual 43 pages 11.27 Kb