Standard Horizon Ff520 owner manual WHY do I Never see Fishes in the Range Between 0 to 2 FEET?

Page 40

surface clutter, and increasing the STC strenght until the image on the screen cleans up. Please note that in very shallow waters it is usually better to switch to manual gain mode to reduce gain fluctuation due to rapidly changing bottom conditions. 2) Using Surface Declutter, increase the Surface Declutter value until the surface declutter disappears completely.

7.11WHY DO I NEVER SEE FISHES IN THE RANGE BETWEEN 0 TO 2 FEET?

The minimum range of the Fish Finder is 2 Feet. In this interval the Fish Finder can detect neither the bottom nor any target.

7.12HOW CAN I REDUCE THE SURFACE CLUTTER?

You can act by: properly setting the STC as described at 7.10 and also by increasing the NOISE LEVEL and reducing the GAIN or the GAIN OFFSET (if you are in auto gain mode). However please note that a strong attenuation of surface clutter may also reduce the capability to detect targets.

7.13THE FISH FINDER IS IN AUTO GAIN MODE BUT THE PIC- TURE DISPLAY TOO MANY SMALL TARGETS, WHAT SHALL I DO TO REDUCE THE SCREEN CLUTTER?

Try increasing the NOISE LEVEL or decreasing the GAIN OFFSET.

7.14IN VERY SHALLOW WATERS WHEN THE AUTO GAIN MODE IS SELECTED THERE ARE FLUCTUATIONS IN THE BOTTOM PROFILE WIDTH AND ITS COLOR REPRESENTATION. WHAT SHOULD I DO?

In very shallow waters the environment situation (bottom/water condition) change very quickly thus causing the auto gain algorithm to create oscillations while trying to set optimal GAIN value for each situation. To avoid this it is advisable to switch to MANUAL GAIN mode and fine tune the GAIN to a fixed setting.

7.15IN VERY DEEP WATERS EVEN SETTING THE GAIN TO ITS MAXIMUM VALUE I CANNOT SEE THE BOTTOM WHAT SHALL I DO?

Try decreasing the NOISE LEVEL. If still the bottom is not visible there is nothing you can do, the bottom echo is simply too weak to be detected.

7.16GPS CHART PLOTTER SHOWS NO DATA WHEN VIEWING THE FISH FINDER PAGE

This may be due to the FF520 having an issue. To confirm, listen to the depth transducer for the transmit pulse. If the pulse is not heard the FF520 is defective.

Page 42

 

FF520

 

Image 40
Contents FF520 FCC Compliance Statement Table of Contents Index Introduction General InformationPacking List Replacement part0 FF520 Packing List Mounting the FF520 InstallationConnections Connecting the GPS Chart Plotters to the FF520 CP155C/CP1000C/CP180/CP180i/CPV350 connections to FF520CP180/CP180i FF520CPV350 FF520 Tee Cable Optional ConnectionsCP175C connections to FF520 Alarm Buzzer LED Status IndicatorNmea Output Second temp sensorSelecting the FF520 Power ConnectionsCP180/CP180i/CPV350 CP155C/CP175C/CP1000C 0 Selecting the FF520 on CP180/CP180i/CPV350Fish Finder Understanding the Fish FinderFish Finder window Color BarUnderstanding the Fish Finder display ScopeOperating Frequency FishesDisplaying the Fish Finder Menu selection for CP155C/CP175C/CP1000CCustomizing the Fish Finder menu selection 0a Menu selection for CP180/CP180i/CPV350Soft Keys for CP175C/CP1000C/CPV350 KEY Operation When Fish Finder page is Shown Customizing the Soft Keys for CP175C/CP1000C/CPV350Menu key Enter keyClear key Zoom in and Zoom OUT keysControls on Chart page or Fish page in Chart/Fish dual mode Mark keyShuttlepoint knob Focus Soft Key for CP175C/CP1000C/CPV350System Update menu Range Soft KeyFrequency Soft Key Sensitivity Time Control STC Soft KeySystem Information page for CP180/CP180i/CPV350 Fish Finder Setup Menu PresetsSelection FishGain Mode Chart/FishRange Menu AutoSensitivity Menu Interference RejectionGain Display Setup Transducer Setup Keel OffsetLoad Settings from User C-CARD AlarmsSave Settings to User C-CARD Restore Current Preset Defaults Page Specifications FF520 SpecificationsFF520 Internal Connections FF520 Internal connectionsPower Boats TransducerTransducer Mounting SailboatsTransducer Types Low Profile Thru-HullTransom Fairing BlockIn-hull Optional Transducer ID SensorsPage Tips of Operations 0a The FF520HOW can I SET Optimal Operating Parameters What are Preset MODES?What are Extreme Situations in Which Auto Modes MAY FAIL? What should I do if the Auto Modes FAIL? WHY do I Never see Fishes in the Range Between 0 to 2 FEET? HOW can I Reduce the Surface CLUTTER?Index 27, 30A N D a R D H O R I Z O N L I M I T E D W a R R a N T Y
Related manuals
Manual 43 pages 11.27 Kb