Raymarine L470 Mounting the Display Unit - Flush Mount, Flush-mount Installation

Page 24

Mounting the Display Unit – Flush Mount

Mounting the Display Unit – Flush Mount

In order to do this installation, you will need the optional flush mounting kit (part no. M99-138). See Fig. 2-12.

1.Select a mounting location on the dashboard or control panel. Choose a clear, flat area at least 7" x 7" (180 mm x 180 mm). Be sure you will also have at least 6" (152 mm) of clearance behind the area where the display unit will be mounted. It is a good idea to drill a small pilot hole in the center of the mounting area. Be sure there are no hidden electrical wires or other items behind the point where you plan to mount the display unit.

2.A mounting template is supplied with the flush mounting kit. Tape this over the selected location on the panel and trace around the edges.

3.Make the cutout for the display. Drill a series of 1/2" (13 mm) holes at the points shown around the edges of the cutout area.

4.Drill the two small holes for the threaded studs as shown on the mounting template. Use a 7/32" (5.5 mm) drill bit.

5.Remove the template and draw straight lines between the 1/2" holes. Cut along each of the lines with a small saw.

Fig. 2-12

Flush-mount

Installation

18	Installation

Image 24

Contents Instruction Manual RaymarineFishFinder L470 Contents InstallationIntroduction Operating Instructions4 Setup Instructions Maintenance and Troubleshooting SpecificationsList of Figures Pageviii Frequency Menu Item1 - Introduction About the FishFinder L470Introduction Optional Accessories System ComponentsStandard Equipment Standard TransducersTransducer switch box select between two L470 2 - Installation InstallationAbout the Transducer Selecting the Correct Type of Transducer Use a transom-mount transducer ifUse a thru-hull transducer if Use an in-hull transducer ifAssembling the Transducer Bracket Positioning the Transom-Mount TransducerUse a trolling motor transducer if Use a Sidelooker transducerTransducer Mounted on Transom Transducer Bracket Side ViewAllow a clearance of at least 10 inches 254 mm 10 254 mm Transducer in released positionNo!No!No Correct Mounting PositionMounting the Transducer Mounting the Transom-Mount Transducer 3. Remove the two screws and the bracket covering the paddle wheels Installation Notes - Thru-Hull Transducer Installation Notes - In-Hull Transducer Installation Notes - Trolling Motor Transducers EMC Installation Guidelines Installation Notes - Transducer for Speed and Temperature OnlySuppression Ferrites Mounting the Display Unit - Standard Mount Dismounting the Display UnitDimensions 2-25/3270 mm 210 mmMounting the Display Unit - Flush Mount Flush-mount InstallationInstalling the Transducer Cable Disassembling from BracketInstalling Cable on Transom Cable feed-thru cap Cable clamp 1 25 mm Hull projectionsFiberglass 1/4 6mm Aluminum 1/2 13 mm Installing the Transducer Cable - Sidelooker Option Installing the Transducer CableInstallation with Separate Speed and Temperature Sensors Making the DC Power Connections DC Power Connections DC 12V connector to battery T/D connector to transducer RED BLACKRF ground Calibrating the Sensors higher value for Speed Cal. If the display unit is reading high, use a smaller number for Speed Cal. You may enter any value between 75 and 3 - Operating Instructions Controls on Display PanelOperating Instructions Up and down arrows - and Left and right arrows - andCLEAR Turning the Power On and Off Setup MemoryLamp/Contrast Menu Operating Pages ModeFunction See pageOnly if Sidelooker feature is turned onFishFinder Page Shallow alarm setAuto frequency on Transducer frequency Top of display Fish alarm set Center of display From the System Setup Menu, you can turn this item off orThis entry shows the speed of the boat through the water Bottom of display Choosing a Frequency Fish Indications When the boat is moving very fast50 kHz 200 kHz An arch-shaped image indicates a fishBottom Indications Bottom Conditions Hard Sand Soft MudRocks Window Page WindowContentsOption A Option C Option E Option G Option B Option D Option F Option HOptions for Window Page Sidelooker Page Once the Sidelooker feature has been turned on, you can reach the Sidelooker page easily. Press the or buttons on the Page Control Pad until the Sidelooker Page appears. The unit will present a display similar to Fig Here are the special items on this display Bottom/Shore Digital Page button. The Log may be reset to zero from the Zoom Mode A-Scope ModeBottom Lock Mode Performance ModesPerformance Modes Zoom ModeZoom display Zoom magnification A-Scope Bottom Coverage Mode Bottom coverage Bottom Lock Mode the selected range, then Bottom Lock will not display the bottom image 4 - Setup Instructions The Setup MenuSetup Instructions Fig.4-1Range Setting Setup InstructionsSidelooker Sensitivity Setting Auto sensitivity Chart Speed Setting Changing the Chart Speed SettingFrequency Setting AUTO frequency Resetting the Log System Setup Menu Fig.4-8different languages. English is the default language which The unit can present the display information in one of sevenSetup Instructions Shallow Alarm For example, if the temperature reading onCLEAR conditions occurs shallow, deep, or fish alarm. For the water. You can silence the buzzer again by pressing theCode Units used for speedUnits used bySetup Menus for Zoom Mode Zoom Select Menufeature is particularly useful when fishing for species of fish button to leave this display, and store the Auto Zoom settingZoom Screen Split/Full Menu Item Setup Menus for Bottom Lock Mode Bottom Lock Range Menu ItemBottom Lock Split/Full Menu Item Setup Menu for Window Page Resetting from the Digital Page Setup Instructions for SidelookerSidelooker Range Menu Item Sidelooker Chart Speed Menu Item Sidelooker Sensitivity Menu ItemSidelooker View Menu Item Display Option Information ShownCombining Displays Resetting the Unit to Factory Defaults Default Settings Default - US model Default - Europe model5 - Maintenance and Troubleshooting Cleaning InstructionsTroubleshooting Suggestions Maintenance and TroubleshootingThe display unit “freezes” temporarily or permanently The display unit does not see the bottom or fish The FishFinder does not display fish archesThe depth setting flashes often The display unit shows lots of background “noise”How to Contact Raymarine For marine product and services informationFor accessories and parts Servicing a Thru-Hull TransducerFor product repair service For technical supportPrepaid Return Service Raymarine in EuropeMaintenance and Troubleshooting 6 - Specifications SpecificationsGeneral Information FishFinder Functions Feet, fathoms, metersConnector Diagrams ConnectorsGlossary of Terms GlossaryNautical mile 6076 feet Statute mile 5280 ftLimited Warranty Certificate Warranty Limitations