Raymarine L470 instruction manual Digital Page, Operating Instructions

Page 53
Digital Page

Digital Page

Fig. 3-11

Digital Page

The Digital Page presents several measurements at the same time using large, easy-to-read digital numbers. To select the Digital Page, press either the < or > button on the Page Control Pad until the Digital Page appears. The Digital image is useful when you are traveling, but not looking for fish or checking the appearance of the bottom. See Fig. 3-11.

The displayed regions on the screen are:

Depth

The depth of the bottom in feet, fathoms, or meters,

 

depending on your selection in the System Setup Menu. If

 

the unit loses its “lock” on the bottom, the last known depth

 

will flash on and off.

Speed

The speed of your boat through the water derived from the

 

impeller. This is measured in MPH (statute miles per hour),

 

KTS (knots, or nautical miles per hour), or KPH (kilometers

 

per hour), depending on your selection in the System Setup

 

display. The speed value may also be calibrated within the

 

System Setup Menu. (See page 64 for details.)

Log

The distance traveled, calculated using the signal from the

 

paddlewheel or impeller. The L470 remembers this value

 

after the unit is turned off, provided the unit is shut off using

Operating Instructions

47

Image 53
Contents FishFinder L470 Instruction ManualRaymarine Installation ContentsIntroduction Operating Instructions4 Setup Instructions Specifications Maintenance and TroubleshootingPage List of FiguresFrequency Menu Item viiiIntroduction 1 - IntroductionAbout the FishFinder L470 System Components Optional AccessoriesStandard Equipment Standard TransducersTransducer switch box select between two L470 About the Transducer 2 - InstallationInstallation Use a transom-mount transducer if Selecting the Correct Type of TransducerUse a thru-hull transducer if Use an in-hull transducer ifPositioning the Transom-Mount Transducer Assembling the Transducer BracketUse a trolling motor transducer if Use a Sidelooker transducerTransducer Bracket Side View Transducer Mounted on TransomAllow a clearance of at least 10 inches 254 mm 10 254 mm Transducer in released positionMounting the Transducer No!No!NoCorrect Mounting Position Mounting the Transom-Mount Transducer 3. Remove the two screws and the bracket covering the paddle wheels Installation Notes - Thru-Hull Transducer Installation Notes - In-Hull Transducer Installation Notes - Trolling Motor Transducers Installation Notes - Transducer for Speed and Temperature Only EMC Installation GuidelinesSuppression Ferrites Dismounting the Display Unit Mounting the Display Unit - Standard Mount2-25/32 Dimensions70 mm 210 mmFlush-mount Installation Mounting the Display Unit - Flush MountDisassembling from Bracket Installing the Transducer CableFiberglass 1/4 6mm Aluminum 1/2 13 mm Installing Cable on TransomCable feed-thru cap Cable clamp 1 25 mm Hull projections Installation with Separate Speed and Temperature Sensors Installing the Transducer Cable - Sidelooker OptionInstalling the Transducer Cable Making the DC Power Connections RF ground DC Power ConnectionsDC 12V connector to battery T/D connector to transducer RED BLACK Calibrating the Sensors higher value for Speed Cal. If the display unit is reading high, use a smaller number for Speed Cal. You may enter any value between 75 and Operating Instructions 3 - Operating InstructionsControls on Display Panel CLEAR Up and down arrows - andLeft and right arrows - and Setup Memory Turning the Power On and OffLamp/Contrast Menu Mode Operating PagesFunction See pageis turned on Only if Sidelooker featureAuto frequency on Transducer frequency FishFinder PageShallow alarm set Top of display Fish alarm set This entry shows the speed of the boat through the water Center of displayFrom the System Setup Menu, you can turn this item off or Bottom of display Choosing a Frequency When the boat is moving very fast Fish Indications50 kHz 200 kHz An arch-shaped image indicates a fishBottom Indications Rocks Bottom ConditionsHard Sand Soft Mud WindowContents Window PageOptions for Window Page Option A Option C Option E Option GOption B Option D Option F Option H Sidelooker Page Once the Sidelooker feature has been turned on, you can reach the Sidelooker page easily. Press the or buttons on the Page Control Pad until the Sidelooker Page appears. The unit will present a display similar to Fig Here are the special items on this display Bottom/Shore Digital Page button. The Log may be reset to zero from the A-Scope Mode Zoom ModeBottom Lock Mode Performance ModesZoom display Performance ModesZoom Mode Zoom magnification A-Scope Bottom Coverage Mode Bottom coverage Bottom Lock Mode the selected range, then Bottom Lock will not display the bottom image The Setup Menu 4 - Setup InstructionsSetup Instructions Fig.4-1Sidelooker Range SettingSetup Instructions Sensitivity Setting Auto sensitivity Changing the Chart Speed Setting Chart Speed SettingFrequency Setting AUTO frequency Resetting the Log Fig.4-8 System Setup MenuThe unit can present the display information in one of seven different languages. English is the default language whichSetup Instructions For example, if the temperature reading on Shallow AlarmCLEAR water. You can silence the buzzer again by pressing the conditions occurs shallow, deep, or fish alarm. For theUnits used for speedUnits used by CodeZoom Select Menu Setup Menus for Zoom Modefeature is particularly useful when fishing for species of fish button to leave this display, and store the Auto Zoom settingZoom Screen Split/Full Menu Item Bottom Lock Range Menu Item Setup Menus for Bottom Lock ModeBottom Lock Split/Full Menu Item Setup Menu for Window Page Setup Instructions for Sidelooker Resetting from the Digital PageSidelooker Range Menu Item Sidelooker Sensitivity Menu Item Sidelooker Chart Speed Menu ItemDisplay Option Information Shown Sidelooker View Menu ItemCombining Displays Resetting the Unit to Factory Defaults Default - US model Default - Europe model Default SettingsCleaning Instructions 5 - Maintenance and TroubleshootingTroubleshooting Suggestions Maintenance and TroubleshootingThe display unit “freezes” temporarily or permanently The FishFinder does not display fish arches The display unit does not see the bottom or fishThe display unit shows lots of background “noise” The depth setting flashes oftenFor marine product and services information How to Contact RaymarineFor accessories and parts Servicing a Thru-Hull TransducerFor technical support For product repair serviceRaymarine in Europe Prepaid Return ServiceMaintenance and Troubleshooting General Information 6 - SpecificationsSpecifications Feet, fathoms, meters FishFinder FunctionsConnectors Connector DiagramsGlossary Glossary of TermsStatute mile 5280 ft Nautical mile 6076 feetWarranty Limitations Limited Warranty Certificate