Raymarine L470 Sidelooker Sensitivity Menu Item, Sidelooker Chart Speed Menu Item

Page 84

Sidelooker Sensitivity Menu Item

Sidelooker Sensitivity Menu Item

Fig. 4-16

Sidelooker

Sensitivity

Menu Item

This menu item allows you to set the sensitivity for the Sidelooker feature only. (This will not change the sensitivity setting for the other display pages.) Choose Auto or Manual sensitivity. If you choose Manual sensitiv- ity, use the < and > arrows of the Page Control Pad to adjust the sensitivity.

If you are done with your setup changes, press the CLEAR button to go back to the normal display. To select the next menu item, press the V arrow of the Page Control Pad.

Sidelooker Chart Speed Menu Item

Fig. 4-17

Sidelooker

Chart Speed

Menu Item

The Chart Speed Menu Item in the Sidelooker Page adjusts the chart speed for the Sidelooker display and the FishFinder display. Remember, if you adjust the chart speed in any menu, both displays will be affected. Using a faster chart speed, there is more space on the display to show a given section of the bottom, so the unit can include more detail. Using a slower chart speed, this same information is displayed in a smaller vertical space. Use the < and > arrows of the Page Control Pad to change the chart speed. Making the bar longer increases the chart speed. If you

78	Setup Instructions

Image 84

Contents Instruction Manual RaymarineFishFinder L470 Contents InstallationIntroduction Operating Instructions4 Setup Instructions Maintenance and Troubleshooting SpecificationsList of Figures Pageviii Frequency Menu Item1 - Introduction About the FishFinder L470Introduction Optional Accessories System ComponentsStandard Equipment Standard TransducersTransducer switch box select between two L470 2 - Installation InstallationAbout the Transducer Selecting the Correct Type of Transducer Use a transom-mount transducer ifUse a thru-hull transducer if Use an in-hull transducer ifAssembling the Transducer Bracket Positioning the Transom-Mount TransducerUse a trolling motor transducer if Use a Sidelooker transducerTransducer Mounted on Transom Transducer Bracket Side ViewAllow a clearance of at least 10 inches 254 mm 10 254 mm Transducer in released positionNo!No!No Correct Mounting PositionMounting the Transducer Mounting the Transom-Mount Transducer 3. Remove the two screws and the bracket covering the paddle wheels Installation Notes - Thru-Hull Transducer Installation Notes - In-Hull Transducer Installation Notes - Trolling Motor Transducers EMC Installation Guidelines Installation Notes - Transducer for Speed and Temperature OnlySuppression Ferrites Mounting the Display Unit - Standard Mount Dismounting the Display UnitDimensions 2-25/3270 mm 210 mmMounting the Display Unit - Flush Mount Flush-mount InstallationInstalling the Transducer Cable Disassembling from BracketInstalling Cable on Transom Cable feed-thru cap Cable clamp 1 25 mm Hull projectionsFiberglass 1/4 6mm Aluminum 1/2 13 mm Installing the Transducer Cable - Sidelooker Option Installing the Transducer CableInstallation with Separate Speed and Temperature Sensors Making the DC Power Connections DC Power Connections DC 12V connector to battery T/D connector to transducer RED BLACKRF ground Calibrating the Sensors higher value for Speed Cal. If the display unit is reading high, use a smaller number for Speed Cal. You may enter any value between 75 and 3 - Operating Instructions Controls on Display PanelOperating Instructions Up and down arrows - and Left and right arrows - andCLEAR Turning the Power On and Off Setup MemoryLamp/Contrast Menu Operating Pages ModeFunction See pageOnly if Sidelooker feature is turned onFishFinder Page Shallow alarm setAuto frequency on Transducer frequency Top of display Fish alarm set Center of display From the System Setup Menu, you can turn this item off orThis entry shows the speed of the boat through the water Bottom of display Choosing a Frequency Fish Indications When the boat is moving very fast50 kHz 200 kHz An arch-shaped image indicates a fishBottom Indications Bottom Conditions Hard Sand Soft MudRocks Window Page WindowContentsOption A Option C Option E Option G Option B Option D Option F Option HOptions for Window Page Sidelooker Page Once the Sidelooker feature has been turned on, you can reach the Sidelooker page easily. Press the or buttons on the Page Control Pad until the Sidelooker Page appears. The unit will present a display similar to Fig Here are the special items on this display Bottom/Shore Digital Page button. The Log may be reset to zero from the Zoom Mode A-Scope ModeBottom Lock Mode Performance ModesPerformance Modes Zoom ModeZoom display Zoom magnification A-Scope Bottom Coverage Mode Bottom coverage Bottom Lock Mode the selected range, then Bottom Lock will not display the bottom image 4 - Setup Instructions The Setup MenuSetup Instructions Fig.4-1Range Setting Setup InstructionsSidelooker Sensitivity Setting Auto sensitivity Chart Speed Setting Changing the Chart Speed SettingFrequency Setting AUTO frequency Resetting the Log System Setup Menu Fig.4-8different languages. English is the default language which The unit can present the display information in one of sevenSetup Instructions Shallow Alarm For example, if the temperature reading onCLEAR conditions occurs shallow, deep, or fish alarm. For the water. You can silence the buzzer again by pressing theCode Units used for speedUnits used bySetup Menus for Zoom Mode Zoom Select Menufeature is particularly useful when fishing for species of fish button to leave this display, and store the Auto Zoom settingZoom Screen Split/Full Menu Item Setup Menus for Bottom Lock Mode Bottom Lock Range Menu ItemBottom Lock Split/Full Menu Item Setup Menu for Window Page Resetting from the Digital Page Setup Instructions for SidelookerSidelooker Range Menu Item Sidelooker Chart Speed Menu Item Sidelooker Sensitivity Menu ItemSidelooker View Menu Item Display Option Information ShownCombining Displays Resetting the Unit to Factory Defaults Default Settings Default - US model Default - Europe model5 - Maintenance and Troubleshooting Cleaning InstructionsTroubleshooting Suggestions Maintenance and TroubleshootingThe display unit “freezes” temporarily or permanently The display unit does not see the bottom or fish The FishFinder does not display fish archesThe depth setting flashes often The display unit shows lots of background “noise”How to Contact Raymarine For marine product and services informationFor accessories and parts Servicing a Thru-Hull TransducerFor product repair service For technical supportPrepaid Return Service Raymarine in EuropeMaintenance and Troubleshooting 6 - Specifications SpecificationsGeneral Information FishFinder Functions Feet, fathoms, metersConnector Diagrams ConnectorsGlossary of Terms GlossaryNautical mile 6076 feet Statute mile 5280 ftLimited Warranty Certificate Warranty Limitations