Lowrance electronic HDS-5X operation manual Bearing alignment, Installation Adjustment Menu

Page 61

Settings

Installation Adjustment Menu

The installation adjustment menu is used to make adjustments to bearing alignment, range offset, antenna height and open array park angle.

When the installation adjustment menu is accessed, press the keypad up/down to select a feature. Press the keypad left/ right to make adjustments to a selected feature.

Press Exit to return to the Radar	Installation menu. To	Adjustment Menu
remove the Radar Installation menu	from the screen, select	Adjustment Menu

Close and press enter.

Bearing alignment

Used to align the bow of your vessel with the heading line (zero point). Bearing alignment is also referred to as zero bearing.

To make adjustments to bearing alignment, switch the radar state to Transmit and set radar orientation to Heading Up.

To select Heading up orientation:

1.From the Radar Page, press MENU.

2.Select Orientation and press ENTER.

3.Use the keypad to select Heading Up and press ENTER.

4.Press EXIT.

Before Bearing Alignment

After Bearing Alignment

Bow of ship is lined up with	Bearing line aligned with
the tip of a peninsula; the	peninsula, matching the
bearing line is not.	alignment of the bow.

59

Image 61

Contents HDS-5x Copyright 2011 Navico All Rights Reserved Table of contents Contents About this manual Manual Conventions IntroductionLowrance HDS-5x Sonar Getting Started Menus LanguageClosing Menus To select a languageTo select a fishing mode Selecting a Fishing ModeEntering Letters in Text Boxes To enter data in a text boxTo Restore Defaults Restore DefaultsPages Screen PagesSelecting Pages Edit Mode To access Edit Overlay menuData Overlay Data Overlay menuTo move/place a gauge Move or Placing a GaugeSelect Data TypeLimits SizeAdd Source Configuration menuTo add a source To remove add source dataOn the Sonar Page you can SonarInfo Radar Page optionalOn the Radar Page you can On the Info Page you canDashboards Info menuEdit Edit Info menu To edit gauge displayTo select info To add source To Configure LimitsTo remove a source To change layout Change LayoutAdd Dashboard To add a dashboardTo access Utilities SettingsUtilities UtilitiesSelecting an Active Panel Displaying Combo PagesTo display a combo Displaying Multiple Panels Adjust Panel SizesTo display multiple panels Left the Info page on the rightTo adjust panel sizes Sonar Operation To access the SonarAuto Sensitivity Sonar MenuSensitivity Range ColorlineFrequency SplitTo Adjust Sensitivity and Colorline AdjustStop Sonar Sonar Options To set Upper and Lower LimitsCustom Upper and Lower Limits Ping SpeedTo select a Split option PaletteTo select a Palette Depth Line Temperature GraphAmplitude Scope Zoom BarsFish ID Measure DistanceTo select a Fish ID option To Measure distanceTo share/receive sonar data Radar Operation optional To access the RadarTo access the Adjust menu Adjust menuRadar menu Radar StateLow, Medium and High Auto GainTo select Auto Gain Acquire Targets Sea ClutterPosition To change the PPI positionLook Ahead SymbologyTo adjust an EBL/VRM AdjustEBL/VRM menu To select an EBL/VRMData Box Guard ZonesTo choose alarm trigger vessels entering or exiting zones Using the Adjust menuTo turn on a Guard Zone To change the shape of Guard ZonesTo access the System menu Settings MenuSystem LanguageTo change Text Size To change Key Beep settingsKey Beeps Time optionalScreen Capture Restore DefaultsTo take a screen capture AdvancedTo adjust cursor settings To access Advanced SettingsPages AboutNetwork Sonar Sonar SettingsNoise Rejection Surface ClarityTo adjust Surface Clarity Manual ModeScroll Speed Fishing Modes Reset Fishing Mode Installation MenuKeel Offset To set Keel Offset Water Speed CalibrationTo calibrate Water Speed Temperature Averaging Temperature CalibrationWater Speed Averaging To select a Water Averaging intervalTransducer Type To select a Temperature Averaging intervalTo select a Transducer Type Target Expansion Radar Settings Menu optionalTarget Trails PaletteOrientation North IndicatorThreshold To change Map OrientationRange Markers Range RingsCompass BearingsTo set T/M or R MarpaCanceling Marpa targets To adjust CPA and Tcpa settingsSelecting Marpa targets To cancel all targets To cancel individual targetsMarpa Settings To select history lengthTarget Alarms InstallationTo set Marpa target alarm To access Radar Installation menuBearing alignment Installation Adjustment MenuTo select Heading up orientation To Adjust Range Offset To Adjust Bearing AlignmentRange offset To Adjust Antenna Height Fast scan mode BR24 Radar onlyAntenna Height TuneManually adjusting Sidelobe suppression Reset Radar to Factory DefaultsSidelobe suppression BR24 only Refuel FuelTo input fuel added To calibrate engines To set tank to fullFuel Used Vessel SetupTo select engine-tank configuration Engine/Tank ConfigurationTo input tank size CalibrateTo enable/disable an Alarm AlarmsUnits Siren EnabledTo auto configure a network Auto ConfigureNetwork Data SourcesRename Data Source menuTo Rename a data source NewTo reset global or local sources Reset Global and Reset LocalTo select a scope Device ListTo configure a device name or device tank size Configuring DevicesTo access calibration instructions To configure device locationInstance Calibrating devicesNmea 2000 receive/send waypoint DiagnosticsTo view waypoints Serial PortsTo access Nmea 0183 Output screen To configure serial portsNmea 0183 Output Demo Mode To adjust CPA or Tcpa settingsTo choose a Demo Mode SimulatorGeneral Specifications HDS-5xUnit Care Cleaning the screenUnit won’t turn on TroubleshootingUnit freezes, locks up, or operates erratically Weak bottom echo, erratic readings or no fish returnsTroubleshooting No fish arches when Fish I.D. is turned off Noise Reset the Unit Update the SoftwareRadar won’t Start Up Troubleshooting Index IndexMarpa Index