Lowrance electronic HDS-5X Range offset, To Adjust Bearing Alignment, To Adjust Range Offset

Page 62

Settings

To Adjust Bearing Alignment:

1.Line up the bow of your vessel with a stationary target (lighthouse, pier, etc) at least 1 nm away

2.Select Adjust Bearing Alignment from the Radar Installation menu and press ENTER. The Installation Adjustment menu will appear.

3.Press the keypad left/right to rotate the radar image so the reference target is at 0° or 12 o’clock from the radar center.

Range offset

Eliminates the time lag between real radar returns and the time it takes data to be processed by the radar software. Range Offset is also referred to as zero range and trigger delay.

Range Offset Sequence. The circle shrinks as range is increased.

To Adjust Range Offset:

1.Use the ZOOM IN/ ZOOM OUT keys to set range to 1/8 nm.

2.Highlight Adjust range offset from the Radar Installation menu and press ENTER. The installation adjustment menu will appear.

3.Press the keypad to the left set range offset to 0. Press enter.

4.If there is a blank, black circle around the center or a solid circle of color at the center, increase the range offset until the circle disappears or almost disappears.

5.If you increase the range offset too far, decrease it until the circle appears again.

60

Image 62

Contents HDS-5x Copyright 2011 Navico All Rights Reserved Table of contents Contents Introduction About this manual Manual ConventionsLowrance HDS-5x Sonar Getting Started Closing Menus LanguageMenus To select a languageEntering Letters in Text Boxes Selecting a Fishing ModeTo select a fishing mode To enter data in a text boxRestore Defaults To Restore DefaultsSelecting Pages PagesPages Screen Data Overlay To access Edit Overlay menuEdit Mode Data Overlay menuSelect Data Move or Placing a GaugeTo move/place a gauge TypeSize LimitsTo add a source Configuration menuAdd Source To remove add source dataSonar On the Sonar Page you canOn the Radar Page you can Radar Page optionalInfo On the Info Page you canEdit Info menuDashboards To select info To edit gauge displayEdit Info menu To remove a source To Configure LimitsTo add source Add Dashboard Change LayoutTo change layout To add a dashboardUtilities SettingsTo access Utilities UtilitiesTo display a combo Displaying Combo PagesSelecting an Active Panel To display multiple panels Adjust Panel SizesDisplaying Multiple Panels Left the Info page on the rightTo adjust panel sizes To access the Sonar Sonar OperationSensitivity Sonar MenuAuto Sensitivity Frequency ColorlineRange SplitStop Sonar AdjustTo Adjust Sensitivity and Colorline Custom Upper and Lower Limits To set Upper and Lower LimitsSonar Options Ping SpeedTo select a Palette PaletteTo select a Split option Amplitude Scope Temperature GraphDepth Line Zoom BarsTo select a Fish ID option Measure DistanceFish ID To Measure distanceTo share/receive sonar data To access the Radar Radar Operation optionalRadar menu Adjust menuTo access the Adjust menu Radar StateTo select Auto Gain Auto GainLow, Medium and High Position Sea ClutterAcquire Targets To change the PPI positionSymbology Look AheadEBL/VRM menu AdjustTo adjust an EBL/VRM To select an EBL/VRMGuard Zones Data BoxTo turn on a Guard Zone Using the Adjust menuTo choose alarm trigger vessels entering or exiting zones To change the shape of Guard ZonesSystem Settings MenuTo access the System menu LanguageKey Beeps To change Key Beep settingsTo change Text Size Time optionalTo take a screen capture Restore DefaultsScreen Capture AdvancedPages To access Advanced SettingsTo adjust cursor settings AboutNoise Rejection Sonar SettingsNetwork Sonar Surface ClarityScroll Speed Manual ModeTo adjust Surface Clarity Fishing Modes Keel Offset Installation MenuReset Fishing Mode To calibrate Water Speed Water Speed CalibrationTo set Keel Offset Water Speed Averaging Temperature CalibrationTemperature Averaging To select a Water Averaging intervalTo select a Transducer Type To select a Temperature Averaging intervalTransducer Type Target Trails Radar Settings Menu optionalTarget Expansion PaletteThreshold North IndicatorOrientation To change Map OrientationCompass Range RingsRange Markers BearingsMarpa To set T/M or RSelecting Marpa targets To adjust CPA and Tcpa settingsCanceling Marpa targets Marpa Settings To cancel individual targetsTo cancel all targets To select history lengthTo set Marpa target alarm InstallationTarget Alarms To access Radar Installation menuTo select Heading up orientation Installation Adjustment MenuBearing alignment Range offset To Adjust Bearing AlignmentTo Adjust Range Offset Antenna Height Fast scan mode BR24 Radar onlyTo Adjust Antenna Height TuneSidelobe suppression BR24 only Reset Radar to Factory DefaultsManually adjusting Sidelobe suppression To input fuel added FuelRefuel To set tank to full To calibrate enginesVessel Setup Fuel UsedTo input tank size Engine/Tank ConfigurationTo select engine-tank configuration CalibrateAlarms To enable/disable an AlarmSiren Enabled UnitsNetwork Auto ConfigureTo auto configure a network Data SourcesTo Rename a data source Data Source menuRename NewTo select a scope Reset Global and Reset LocalTo reset global or local sources Device ListConfiguring Devices To configure a device name or device tank sizeInstance To configure device locationTo access calibration instructions Calibrating devicesTo view waypoints DiagnosticsNmea 2000 receive/send waypoint Serial PortsNmea 0183 Output To configure serial portsTo access Nmea 0183 Output screen To choose a Demo Mode To adjust CPA or Tcpa settingsDemo Mode SimulatorSpecifications HDS-5x GeneralCleaning the screen Unit CareUnit freezes, locks up, or operates erratically TroubleshootingUnit won’t turn on Weak bottom echo, erratic readings or no fish returnsTroubleshooting No fish arches when Fish I.D. is turned off Noise Radar won’t Start Up Update the SoftwareReset the Unit Troubleshooting Index IndexMarpa Index