Uniden CXAI 5198 Using Your Answering System, Selecting Your Greeting, Announce only feature

Page 44

Selecting Your Greeting

With the phone in standby mode, press greeting. Then press greeting again while the outgoing message is played. This switches between the prerecorded greeting and the personal greeting. After finishing playing back the message, a confirmation tone is heard.

Announce only feature

The announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set announce only, follow the steps on “Setting the Record Time” page 39. If you want to use your own greeting and you want to change your greeting to omit the prompt to leave a message, refer to “Selecting Your Greeting” above.

The following message is pre-recorded:

“Hello, no one is available to take your call. Please call again.”

Using Your Answering System

The message counter displays the number of messages stored in memory. If the message LED flashes, then there are new messages waiting for you. The answering system is designed to play your new messages first. After you play all your new messages, you can then play your old messages.

[ 4 3 ] T H E I N T E G R A T E D A N S W E R I N G D E V I C E

w w w . u n i d e n . c o m

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Series Owners Manual Contents Welcome Features Terminology Talk and Standby TimesControls & Functions With Handset Remote keysRepeat/rewind P.44 Call id P.35 Play/stop P.44 Setting up the Phone Do the following stepsConnect the base unit Install the rechargeable battery pack into the handset Connect the charger Mount the base unit on a wall if desired Standard wall plate mountingInstalling the Beltclip Direct wall mountingTo attach the beltclip To remove the beltclipOptional Headset Installation Base Setup Adjusting the LCD ContrastSetting the Dial Mode Setting Day and TimeSetting the Area Code Setting Caller ID on Call Waiting CidcwHandset Setup Using the interfaceSetting AutoTalk Selecting a Language Handset onlyChecking Area Code selected from the Handset Using Your Phone Power Failure OperationMaking and Receiving Calls Making a call From the handsetFrom the base Receiving a call From the handsetRedialing the last dialed number Hanging UpCall Waiting Placing a Call on HoldSetting the Base Ringer Volume Adjusting the Ringer, and Earpiece and Speaker VolumeSelecting the Handset Ring Tone and Volume Earpiece and Speaker Volume Muting the RingerDo Not Disturb DND Temporarily Muting the RingerTraveling Out of Range Tone Dialing Switch-overMute Base Microphone Joining a Conference Call Selecting a Different ChannelConferencing Making an Intercom Page While the Line is on Hold IntercomMaking an Intercom Answering an Intercom Press talk/flash or select/int’comUsing the Speed Dial Memory Storing Names and Numbers in Speed Dial MemoryUse delete/channel If you make a mistake while entering a nameNumber of times key is pressed Keys Storing Caller ID data in Speed Dial Memory To cancel speed dialing Making Calls from Speed Dial MemoryWhen the Telephone Rings Caller ID and Caller ID on Call Waiting CidcwViewing the Caller ID Data Deleting all Caller ID names/numbers Deleting Data from the Caller ID ListDeleting a Caller ID Data Volume or / / /select/volume Making a Call from the Caller ID DataFeatures Integrated Answering DeviceSetting the Call Screen Setting Up the Answering MachineSetting the Record Time Turning the message alert tone off by pressing any key Setting the Ring TimeSetting the Message Alert On or Off Setting a Security Code PIN Code Turning the Answering System On/OffSetting Your Outgoing Message Greeting Record a Personal Outgoing MessageSelecting Your Greeting Using Your Answering SystemAnnounce only feature Playing your messages Repeating a messageSkipping a message Deleting a messageVoice memo Voice memo messages are recorded as an incoming messagesRecording a conversation Screening a callRemote access with any touch-tone telephone Remote OperationFunction Remote Access with the Handset Turn on the Answering System RemotelyFunction Battery replacement and handling Power FailureLow battery alert Cleaning the battery charging contacts Battery Information General InformationAC Adapter Information FrequencyTroubleshooting Symptom SuggestionSevere noise interference Liquid Damage Case ActionPrecautions Installation Considerations Terminal Equipment Index Remote Operation Card Remote Operation Card Memory Location MemoE M O T E O P E R a T I O N C a R D Memo Memo At Uniden, well take care of you Help for our Special Needs CustomersUCZZ010 06BA0
Top Page Image Contents