1.43 Background Color
The secondary function of the BRILL control (BKGND COLOR) is to select the color of the background, characters, menu, markers and indications, from the five color combinations shown in the table below. Each press of the control selects one of the five color combina- tions.
Table 1-4 Available color combinations
Arrangement | 1 | 2 | 3 | 4 | 5 | |
|
|
|
|
|
| |
Radar Display | BLK | BLU | BLU | BLU | BLK | |
Area | ||||||
|
|
|
|
| ||
|
|
|
|
|
| |
Outside Radar | BLK | BLK | BLK | BLU | BLK | |
Display Area | ||||||
|
|
|
|
| ||
|
|
|
|
|
| |
Characters | GRN | GRN | GRN | WHT | RED | |
|
|
|
|
|
| |
Menu | YEL | YEL | YEL | YEL | RED | |
|
|
|
|
|
| |
Menu Highlight | YEL | YEL | YEL | YEL | RED | |
|
|
|
|
|
| |
EBL/VRM | GRN | GRN | GRN | |||
|
|
|
|
|
| |
Range Rings | GRN | WHT | WHT | WHT | GRN | |
|
|
|
|
|
| |
Cursor | WHT | GRN | GRN | GRN | WHT | |
|
|
|
|
|
| |
Heading Line | GRN | WHT | WHT | WHT | GRN | |
|
|
|
|
|
| |
Target Alarm | WHT | WHT | ||||
Zone | ||||||
|
|
|
|
| ||
|
|
|
|
|
| |
North Marker | WHT | WHT | ||||
|
|
|
|
|
| |
Stern Marker | WHT | WHT | ||||
|
|
|
|
|
|
BLK, Black; BLU, Blue;
1.44 Selecting Range Scales
Range scales to use may be selected as fol- lows:
1.Press the [MENU] key.
2.Press the [0] key four times to display the OTHER sub menu.
OTHER
1.↑
2.TEST
3.DEGAUSS
4.TIME ALARM
5.RANGE
6.INSTALL
Figure 1-53 OTHER sub menu
3. Press the [5] key twice to select RANGE.
|
| RANGE |
|
|
|
|
|
|
|
| ||||
1. | ↑ |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2. | RANGE |
| 1/8 |
|
| 1/4 |
|
| 1/2 |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
| 3/4 |
|
| 1 | 1.5 |
| 2 | 3 |
| |||
|
| 4 | 6 | 8 | 12 | 16 |
|
| ||||||
|
| 24 |
|
| 32 | 48 |
| 72 | 96 | 120 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 1-54 RANGE menu
4.Press the [2] key to place the underline under the range scale to select/deselect and then press the [ENTER/SELECT] key. Active ranges are highlighted. Repeat to select/deselect other ranges.
5.Press the [MENU] key.
1.45Selecting Bearing Scale Format
The bearing scale may be displayed in de- grees or compass points or degrees as fol- lows:
1.Press the [MENU] key.
2.Press the [0] key twice to display the OTHER menu.
3.Press the [6] key twice to display the MARK/LINE menu.
| MARK/LINE |
| |||
1. | ↑ |
|
|
|
|
|
|
|
|
|
|
2. | INDEX LINES | 2 |
|
| 6 |
|
|
|
| ||
3. | STERN MARK | OFF |
| ON | |
|
|
|
| ||
4. | SHIP’S MARK | OFF |
| ON | |
|
|
|
|
| |
5. | BEARING SCALE | 360 |
| COMPASS | |
|
|
|
|
|
|
Figure 1-55 MARK/LINE menu
4.Press the [5] key to select 360 (degrees) or COMPASS.
5.Press the [ENTER/SELECT] key to reg- ister your selection and the [MENU] key to close the menu.