Furuno 1964C, 1954C, 1944C, 1934C, 1834C, 1824C Antenna unit, showing location of mounting hardware

Page 13

1.2.2 Mounting procedure

1.Remove the mounting hardware from the bottom of the antenna unit: four each of hex bolts (M10X20), spring washers and flat washers. Save the mounting hardware to use it to fix the antenna unit to the mounting platform later on.

Stern

Bow

 

Screws

two screws on other side

Flat washer

Spring washer

Hex bolt (M10 x 20)

Antenna unit, showing location of mounting hardware

2.Construct a platform (wood, steel*, or aluminum) of 5-10 mm (recommended dimension) in thickness referring to the outline drawing at back of this manual. Fasten the platform to the mounting location. Next, position the mounting base on the platform so the cable entrance faces the stern direction.

*: For steel platform take appropriate measures to prevent corrosion.

Note: When drilling holes in the platform, be sure they are parallel with the fore and aft line.

3.Using the hex bolts, flat washers and spring washers removed at step 1, fasten the mounting base to the platform. The torque should be between 19.6-24.5 Nm.

Note: Longer hex bolts (M10X25) are supplied with the installation materials. Use them instead of the hex bolts removed earlier if the mounting platform thickness is 5–10 mm.

 

Transceiver

 

 

module

 

Efeective

Antenna base

 

assy.

 

thread

 

 

 

length:

 

 

12 mm

 

 

 

5 mm or under : M10x20

 

5-10mm:

M10x25

 

over 10 mm:

locally supplied bolts

Flat

Platform

 

washer

 

Spring

washerHex bolt Apply silicone sealant. (M10 x 25

or M10 x 20)

How to fasten the mounting base to platform

1-5

Image 13
Contents VX2 00015180319 Safety Instructions Standard supply Equipment ListsIii Optional supplyCon’t from next NavNet system MODEL1824C/1834C/1934C/1944C/1954C/1964C System ConfigurationsNavNet system GD-1920C AIS ReceiverThree-or-more unit NavNet system Two-unit NavNet systemMounting considerations Mounting the Display UnitTabletop, overhead mounting method Tabletop, overhead mounting Mounting procedureTabletop, overhead mounting of display unit Fixing screw, side view Flush mountingFlush mounting of display unit Mounting the Antenna Unit of MODEL1824C Typical antenna unit placement on sailboat and powerboatAntenna unit, showing location of mounting hardware How to fasten the mounting base to platformAntenna unit, inside view GND Location of EMI core Sectional viewEMI core, putting into core case How to pass the rotation detector cableAntenna unit, clamping the rotation detector cable Contents of mounting bracket 2 kit Type OP03-93, Code NoMounting the optional mounting bracket Part Type Code No QtyHow to assemble and mount the optional mounting bracket Antenna unit Mounting the Antenna Unit of MODEL1834CAntenna unit, cover removed Wiring and final preparations How to fasten the radome base to the mounting platformRF unit Signal cable, antenna unit sideEMI core How to position the radome coverContents of mounting bracket 1 Type OP03-92, Code No Mounting the Antenna Unit of MODEL1934C/1944C/1954C/1964C Coating the antenna with silicone sealant Fastening the radiator to the radiator bracketFastening the radiator bracket to the antenna unit chassis Location of rubber mat Mounting the antenna unitFixing the antenna unit chassis How to fasten antenna unit to mounting platformGround Antenna unit chassis, upper chassis separated Using inside fixing holes of the antenna housingPassing the signal cable through the cable gland assembly Connecting the signal cableAntenna unit chassis, cover opened How to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Power supply unit PSU-005 for Model 1954C Mounting the Power Supply Unit Model 1954C/1964CPower supply unit Power supply unit PSU-008 for Model 1964C This page is intentionally left blank 12-24 VDC Standard WiringDisplay unit, rear view DJ-1 Waterproofing cap and connector nut, sectional viewGround terminal DATA1 to DATA4Network port Connecting GP-310B/320B to Data 2 portRadar Plotter Network sounderExternal Buzzer optional supply MJ-A7SPF0007-050 cable connection for PC How to Connect with a PCPower supply unit PSU-005 MODEL1954C Wiring the Power Supply Unit Model 1954C/1964CPower supply unit, cover removed Cabling Power supply unit PSU-008 MODEL1964CPower supply unit, inside view Jumper block, slide switch settingJumper block, slide switch Function Setting Power requirement Power requirement, replacement of fusesReplacement of fuses This page is intentionally left blank Installation wizard, language selection window Setting up with the Installation WizardInstallation wizard, network setup Installation wizard, units of measurementETR0 Installation wizard, radar setup Tuning Power Supply Unit for Model 1954C Examples of improper and correct sweep timing Wide Wind Averaging Installation wizard, nav setupFuruno BB GPS GPS Receiver NAV Setup menu descriptionDescription Settings Default Setting GPS Setup menu descriptionDescription Contents of Waas Setup menu Waas setup requires GPS receiver GP-320B/330BInstallation wizard, DATA1 GPS/NMEA port setup menu Installation wizard, DATA2 Nmea port setup menuDATA2 port Installation wizard, port monitor displayDATA4 port Installation wizard, Nmea sentence selection window MODEL1824C MODEL1834C Checking Magnetron Heater VoltageThis page is intentionally left blank ARP Kit ARP-11 Contents of ARP kitNecessary parts Name Type Code No QtyBoard Dismounting the Power BoardOrder of fastening screws Contents of NTSC/PAL Interface kit Connecting video equipmentName Type Code No Qty Remarks NTSC/PAL Interface Board attachment Cable 3C-2V, sectional viewDisplay unit, passing the PIP cable Cable ties attachmentHow to connect 15SDS/XHP10-005 Connecting an external monitorNecessary parts for external monitor How to connect remote signal cable Connecting remote displayAttaching more than two units Attaching the cable tie to Power Board0%%5㨮0%#42%5  +/05+105+0&4#9+014440%10.#. 㨻㩧㩍㩏 +/05+105+0&4#9+014440%10. 工事材料表 257 000-155-827-10 Page Page Page Hatai ,WN4UWOK Page Page Marine Radar Model 1934C/1944C Model 1954C Model 1964C Color Video Plotter
Related manuals
Manual 239 pages 53.43 Kb Manual 10 pages 42.92 Kb

1824C, 1934C, 1954C, 1834C, 1964C specifications

Furuno is renowned in the marine electronics industry for producing high-quality navigation equipment, particularly its range of radars. Among its flagship models, the Furuno 1944C, 1964C, 1834C, 1954C, and 1934C stand out due to their advanced features, robust technology, and reliability, making them essential tools for both commercial and recreational vessels.

The Furuno 1944C is a 12-inch color radar that boasts a powerful 4 kW output. This model integrates a user-friendly interface that enhances operational convenience, providing mariners with critical navigation information at their fingertips. With features such as advanced target detection and tracking, it helps to identify vessels and obstacles efficiently, which is vital for safe navigation.

Next, the 1964C takes functionality further with its larger 19-inch display and enhanced signal processing capabilities. The 1964C not only provides an impressive range but also features ARPA (Automatic Radar Plotting Aid) for tracking multiple targets. This functionality allows boat operators to assess risk levels and make informed decisions regarding navigation in busy waterway environments.

The Furuno 1834C is another notable entry in the series, maximizing real-time data display. Its ability to work seamlessly with Furuno's Navigator and Fish Finder systems means it doubles in utility for those who require both navigation and fishing capabilities. The intuitive interface makes it easy to access essential information, ensuring that users can maintain their focus on the sea.

The 1954C radar system incorporates some of the most advanced radar technology, providing detailed target information and exceptional clarity through its color display. Its 4 kW output delivers long-range detection, making it a suitable choice for larger vessels operating in various maritime conditions.

Lastly, the Furuno 1934C rounds out this impressive lineup with its compact design, tailored for smaller boats without sacrificing performance. Its solid 4 kW radar provides excellent target separation and enhanced echo clarity. In addition, it is compatible with a variety of additional sensors, allowing operators to expand their situational awareness.

All these models share common features including a weatherproof design, multiple display modes, and customizable settings, ensuring they cater to a diverse range of maritime applications. With Furuno's continuous innovation and commitment to quality, these radar systems embody the brand's legacy in safety and performance at sea.