Effective thread length
25 mm
Flat washer
Antenna base plate
Gasket
Radome
5 - 10 mm
Spring | Platform |
washer | M10 x 25 |
Apply silicone sealant. | Hex bolt |
How to fasten the radome base to the mounting platform
Wiring and final preparations
4.Drill a hole of approx. 16 mm diameter through the deck or bulkhead to run the signal cable between the antenna unit and the display unit. (To prevent electrical interference avoid running the signal cable near other electrical equipment and in parallel with power cables.) Pass the cable through the hole. Then, seal the hole with sealing compound for waterproofing.
5.Remove three shield covers in the radome.
6.Remove the cable clamping plate by unfastening four screws and removing a gasket.
| Shield cover | Screws |
| Screws | 4 pcs. |
| Cable clamping plate |
| 7 pcs. |
| Shield cover | Gasket |
| |
Screws ![](/images/new-backgrounds/1148599/14859941xi3.webp)
7 pcs. ![](/images/new-backgrounds/1148599/14859941xi5.webp)
Screws 6 pcs.
Shield cover
Antenna unit, inside view
7.Pass the cable through the hole at the bottom of the radome base.
8.Secure the cable with the cable clamping plate and gasket. Ground the shield wire by one of the screws of the cable clamping plate.
VX2
00015180319
Safety Instructions
Standard supply
Equipment Lists
Optional supply
Iii
Con’t from next
NavNet system MODEL1824C/1834C/1934C/1944C/1954C/1964C
System Configurations
NavNet system GD-1920C
AIS Receiver
Three-or-more unit NavNet system
Two-unit NavNet system
Mounting the Display Unit
Mounting considerations
Tabletop, overhead mounting method
Mounting procedure
Tabletop, overhead mounting
Tabletop, overhead mounting of display unit
Flush mounting
Fixing screw, side view
Flush mounting of display unit
Mounting the Antenna Unit of MODEL1824C
Typical antenna unit placement on sailboat and powerboat
Antenna unit, showing location of mounting hardware
How to fasten the mounting base to platform
Antenna unit, inside view
GND
Location of EMI core
Sectional view
EMI core, putting into core case
How to pass the rotation detector cable
Antenna unit, clamping the rotation detector cable
Contents of mounting bracket 2 kit Type OP03-93, Code No
Mounting the optional mounting bracket
Part Type Code No Qty
How to assemble and mount the optional mounting bracket
Mounting the Antenna Unit of MODEL1834C
Antenna unit
Antenna unit, cover removed
Wiring and final preparations
How to fasten the radome base to the mounting platform
RF unit
Signal cable, antenna unit side
EMI core
How to position the radome cover
Contents of mounting bracket 1 Type OP03-92, Code No
Mounting the Antenna Unit of MODEL1934C/1944C/1954C/1964C
Fastening the radiator to the radiator bracket
Coating the antenna with silicone sealant
Fastening the radiator bracket to the antenna unit chassis
Location of rubber mat
Mounting the antenna unit
Fixing the antenna unit chassis
How to fasten antenna unit to mounting platform
Ground
Antenna unit chassis, upper chassis separated
Using inside fixing holes of the antenna housing
Connecting the signal cable
Passing the signal cable through the cable gland assembly
Antenna unit chassis, cover opened
How to fix signal cable in cable gland
Torque 9.8 ±0.1 N .m
Mounting the Power Supply Unit Model 1954C/1964C
Power supply unit PSU-005 for Model 1954C
Power supply unit
Power supply unit PSU-008 for Model 1964C
This page is intentionally left blank
Standard Wiring
12-24 VDC
Display unit, rear view
DJ-1
Waterproofing cap and connector nut, sectional view
Ground terminal
DATA1 to DATA4
Network port
Connecting GP-310B/320B to Data 2 port
Radar Plotter
Network sounder
External Buzzer optional supply
MJ-A7SPF0007-050 cable connection for PC
How to Connect with a PC
Wiring the Power Supply Unit Model 1954C/1964C
Power supply unit PSU-005 MODEL1954C
Power supply unit, cover removed
Cabling
Power supply unit PSU-008 MODEL1964C
Jumper block, slide switch setting
Power supply unit, inside view
Jumper block, slide switch Function Setting
Power requirement, replacement of fuses
Power requirement
Replacement of fuses
This page is intentionally left blank
Installation wizard, language selection window
Setting up with the Installation Wizard
Installation wizard, network setup
Installation wizard, units of measurement
ETR0
Installation wizard, radar setup
Tuning Power Supply Unit for Model 1954C
Examples of improper and correct sweep timing
Wide
Wind Averaging
Installation wizard, nav setup
Furuno BB GPS GPS Receiver
NAV Setup menu description
Description Settings Default Setting
GPS Setup menu description
Description
Contents of Waas Setup menu
Waas setup requires GPS receiver GP-320B/330B
Installation wizard, DATA1 GPS/NMEA port setup menu
Installation wizard, DATA2 Nmea port setup menu
Installation wizard, port monitor display
DATA2 port
DATA4 port
Installation wizard, Nmea sentence selection window
MODEL1824C MODEL1834C
Checking Magnetron Heater Voltage
This page is intentionally left blank
ARP Kit ARP-11
Contents of ARP kit
Necessary parts
Name Type Code No Qty
Board
Dismounting the Power Board
Order of fastening screws
Connecting video equipment
Contents of NTSC/PAL Interface kit
Name Type Code No Qty Remarks
NTSC/PAL Interface Board attachment
Cable 3C-2V, sectional view
Display unit, passing the PIP cable
Cable ties attachment
Connecting an external monitor
How to connect 15SDS/XHP10-005
Necessary parts for external monitor
How to connect remote signal cable
Connecting remote display
Attaching more than two units
Attaching the cable tie to Power Board
0%%5㨮0%#42%5
+/05+105+0&4#9+014440%10.#.
㨻㩧㩍㩏
+/05+105+0&4#9+014440%10.
工事材料表
257
000-155-827-10
Page
Page
Page
Hatai
,WN4UWOK
Page
Page
Marine Radar
Model 1934C/1944C
Model 1954C
Model 1964C
Color Video Plotter