Furuno 1934C, 1954C, 1964C Connecting an external monitor, Necessary parts for external monitor

Page 69

4.2.2 Connecting an external monitor

You can display the MODEL1824C/1834C/1934C/1944C/1954C screen on an external monitor which accepts industrial standard VGA input by using the optional RGB output cable kit OP03-176. Supply monitor and interconnection cable (with HD-15P connectors of male, three rows of 15 pins) locally.

Necessary parts for external monitor

 

Name:

RGB output cable kit

 

 

Type:

OP03-176

 

 

Code No.:

008-526-360

 

 

Name

 

Type

Code No.

Qty

Cable assy.

15SDS/XHP10-005

000-144-511

1

 

 

 

 

 

 

 

 

 

Grommet

 

MG-4

000-871-378

1

1.Unscrew 15 binding screws (M3x10, w/nylon washer) and seven connector nuts to remove the display unit cover.

2.Cut a “cross” in the grommet (to pass the cable).

3.Pass the RGB output cable through the grommet hole at the rear of the display unit cover and the saddle on the POWER Board, and then connect the XH connector (10P) of the RGB output cable to J110 on the SPU Board. Put the ground wire of the cable outside of the cover.

4.Reassemble the display unit referring to the illustration on page 4-3.

5.Fix the ground wire of the cable with one of two screws both sides of the connector hole.

6.Finally, cover the hole with soft putty to seal

Connector nut (large) 1 pc.

Binding screws

(M3x10, w/nilon washer) 15 pcs.

Ground wire (to the out side

of the cover)

J109

Saddle

Connector nut (for 24P) 1 pc.

Connector nut (small) 5 pcs.

Rubber grommet Cut a "cross"

RGB output cable (15SDS/XHP10-005)

J110

How to connect 15SDS/XHP10-005

4-7

Image 69
Contents VX2 00015180319 Safety Instructions Standard supply Equipment ListsOptional supply IiiCon’t from next NavNet system MODEL1824C/1834C/1934C/1944C/1954C/1964C System ConfigurationsNavNet system GD-1920C AIS ReceiverThree-or-more unit NavNet system Two-unit NavNet systemMounting the Display Unit Mounting considerationsTabletop, overhead mounting method Mounting procedure Tabletop, overhead mountingTabletop, overhead mounting of display unit Flush mounting Fixing screw, side viewFlush mounting of display unit Mounting the Antenna Unit of MODEL1824C Typical antenna unit placement on sailboat and powerboatAntenna unit, showing location of mounting hardware How to fasten the mounting base to platformAntenna unit, inside view GND Location of EMI core Sectional viewEMI core, putting into core case How to pass the rotation detector cableAntenna unit, clamping the rotation detector cable Contents of mounting bracket 2 kit Type OP03-93, Code NoMounting the optional mounting bracket Part Type Code No QtyHow to assemble and mount the optional mounting bracket Mounting the Antenna Unit of MODEL1834C Antenna unitAntenna unit, cover removed Wiring and final preparations How to fasten the radome base to the mounting platformRF unit Signal cable, antenna unit sideEMI core How to position the radome coverContents of mounting bracket 1 Type OP03-92, Code No Mounting the Antenna Unit of MODEL1934C/1944C/1954C/1964C Fastening the radiator to the radiator bracket Coating the antenna with silicone sealantFastening the radiator bracket to the antenna unit chassis Location of rubber mat Mounting the antenna unitFixing the antenna unit chassis How to fasten antenna unit to mounting platformGround Antenna unit chassis, upper chassis separated Using inside fixing holes of the antenna housingConnecting the signal cable Passing the signal cable through the cable gland assemblyAntenna unit chassis, cover opened How to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Mounting the Power Supply Unit Model 1954C/1964C Power supply unit PSU-005 for Model 1954CPower supply unit Power supply unit PSU-008 for Model 1964C This page is intentionally left blank Standard Wiring 12-24 VDCDisplay unit, rear view DJ-1 Waterproofing cap and connector nut, sectional viewGround terminal DATA1 to DATA4Network port Connecting GP-310B/320B to Data 2 portRadar Plotter Network sounderExternal Buzzer optional supply MJ-A7SPF0007-050 cable connection for PC How to Connect with a PCWiring the Power Supply Unit Model 1954C/1964C Power supply unit PSU-005 MODEL1954CPower supply unit, cover removed Cabling Power supply unit PSU-008 MODEL1964CJumper block, slide switch setting Power supply unit, inside viewJumper block, slide switch Function Setting Power requirement, replacement of fuses Power requirementReplacement of fuses This page is intentionally left blank Installation wizard, language selection window Setting up with the Installation WizardInstallation wizard, network setup Installation wizard, units of measurementETR0 Installation wizard, radar setup Tuning Power Supply Unit for Model 1954C Examples of improper and correct sweep timing Wide Wind Averaging Installation wizard, nav setupFuruno BB GPS GPS Receiver NAV Setup menu descriptionDescription Settings Default Setting GPS Setup menu descriptionDescription Contents of Waas Setup menu Waas setup requires GPS receiver GP-320B/330BInstallation wizard, DATA1 GPS/NMEA port setup menu Installation wizard, DATA2 Nmea port setup menuInstallation wizard, port monitor display DATA2 portDATA4 port Installation wizard, Nmea sentence selection window MODEL1824C MODEL1834C Checking Magnetron Heater VoltageThis page is intentionally left blank ARP Kit ARP-11 Contents of ARP kitNecessary parts Name Type Code No QtyBoard Dismounting the Power BoardOrder of fastening screws Connecting video equipment Contents of NTSC/PAL Interface kitName Type Code No Qty Remarks NTSC/PAL Interface Board attachment Cable 3C-2V, sectional viewDisplay unit, passing the PIP cable Cable ties attachmentConnecting an external monitor How to connect 15SDS/XHP10-005Necessary parts for external monitor How to connect remote signal cable Connecting remote displayAttaching more than two units Attaching the cable tie to Power Board0%%5㨮0%#42%5  +/05+105+0&4#9+014440%10.#. 㨻㩧㩍㩏 +/05+105+0&4#9+014440%10. 工事材料表 257 000-155-827-10 Page Page Page Hatai ,WN4UWOK Page Page Marine Radar Model 1934C/1944C Model 1954C Model 1964C Color Video Plotter
Related manuals
Manual 239 pages 53.43 Kb Manual 10 pages 42.92 Kb

1824C, 1934C, 1954C, 1834C, 1964C specifications

Furuno is renowned in the marine electronics industry for producing high-quality navigation equipment, particularly its range of radars. Among its flagship models, the Furuno 1944C, 1964C, 1834C, 1954C, and 1934C stand out due to their advanced features, robust technology, and reliability, making them essential tools for both commercial and recreational vessels.

The Furuno 1944C is a 12-inch color radar that boasts a powerful 4 kW output. This model integrates a user-friendly interface that enhances operational convenience, providing mariners with critical navigation information at their fingertips. With features such as advanced target detection and tracking, it helps to identify vessels and obstacles efficiently, which is vital for safe navigation.

Next, the 1964C takes functionality further with its larger 19-inch display and enhanced signal processing capabilities. The 1964C not only provides an impressive range but also features ARPA (Automatic Radar Plotting Aid) for tracking multiple targets. This functionality allows boat operators to assess risk levels and make informed decisions regarding navigation in busy waterway environments.

The Furuno 1834C is another notable entry in the series, maximizing real-time data display. Its ability to work seamlessly with Furuno's Navigator and Fish Finder systems means it doubles in utility for those who require both navigation and fishing capabilities. The intuitive interface makes it easy to access essential information, ensuring that users can maintain their focus on the sea.

The 1954C radar system incorporates some of the most advanced radar technology, providing detailed target information and exceptional clarity through its color display. Its 4 kW output delivers long-range detection, making it a suitable choice for larger vessels operating in various maritime conditions.

Lastly, the Furuno 1934C rounds out this impressive lineup with its compact design, tailored for smaller boats without sacrificing performance. Its solid 4 kW radar provides excellent target separation and enhanced echo clarity. In addition, it is compatible with a variety of additional sensors, allowing operators to expand their situational awareness.

All these models share common features including a weatherproof design, multiple display modes, and customizable settings, ensuring they cater to a diverse range of maritime applications. With Furuno's continuous innovation and commitment to quality, these radar systems embody the brand's legacy in safety and performance at sea.