Furuno 1954C, 1964C, 1944C, 1934C, 1834C, 1824C Installation wizard, nav setup, Wind Averaging

Page 54

a)Set ship’s heading toward a suitable target (for example, ship or buoy) at a range between 0.125 and 0.25 nautical mile.

b)Rotate the ENTER knob to bisect the target with the EBL and press the SET soft key

c)Press the RETURN soft key.

d)As a final test, move the boat towards a small buoy and confirm that the buoy shows up dead ahead on the radar when it is visually dead ahead.

33.The next step is to set up external equipment. Press the NEXT soft key to show the NAV SETUP menu.

POSITION SOURCE

 

FURUNO BB GPS

 

SPEED (STW) SOURCE

 

ETR

 

TEMPERATURE SOURCE

 

ETR

 

DETPH SOURCE

 

ETR

 

STW CALIBRATION

 

+00%

 

TEMP CALIBRATION

 

+00.0°F

 

DEPTH CALIBRATION

 

+00ft

 

WIND AVERAGING

 

001 seconds(s)

 

WIND DIRECTION OFFSET

S000.0°

 

WIND SPEED CALIBRATION

+00%

 

WIND (MWV) SOURCE

 

FURUNO BB GPS

 

STW

TEMP

56.3°F

DEPTH

99.5ft

12.3 kt

 

 

WIND SPEED

WIND DIR

131°

 

 

1.2 kt

 

 

 

Page 1

AIR TEMPERATURE SOURCE FURUNO BB GPS

AIR PRESSURE SOURCE

FURUNO BB GPS

STW

TEMP

DEPTH

12.3 kt

56.3°F

99.5ft

WIND SPEED

WIND DIR

 

1.2 kt

131°

 

Page 2

Installation wizard, nav setup

34.Choose item and press the EDIT soft key.

35.Choose appropriate setting and then press the ENTER soft key. Refer to the table on next page for description of each item.

3-8

Page 53 Page 55
Image 54
Page 53 Page 55
Contents
VX2 00015180319 Safety Instructions Equipment Lists Standard supplyOptional supply IiiCon’t from next System Configurations NavNet system MODEL1824C/1834C/1934C/1944C/1954C/1964CAIS Receiver NavNet system GD-1920CTwo-unit NavNet system Three-or-more unit NavNet systemMounting the Display Unit Mounting considerationsTabletop, overhead mounting method Mounting procedure Tabletop, overhead mountingTabletop, overhead mounting of display unit Flush mounting Fixing screw, side viewFlush mounting of display unit Typical antenna unit placement on sailboat and powerboat Mounting the Antenna Unit of MODEL1824CHow to fasten the mounting base to platform Antenna unit, showing location of mounting hardwareAntenna unit, inside view GND Sectional view Location of EMI coreHow to pass the rotation detector cable EMI core, putting into core caseMounting the optional mounting bracket Contents of mounting bracket 2 kit Type OP03-93, Code NoAntenna unit, clamping the rotation detector cable Part Type Code No QtyHow to assemble and mount the optional mounting bracket Mounting the Antenna Unit of MODEL1834C Antenna unitAntenna unit, cover removed How to fasten the radome base to the mounting platform Wiring and final preparationsSignal cable, antenna unit side RF unitHow to position the radome cover EMI coreContents of mounting bracket 1 Type OP03-92, Code No Mounting the Antenna Unit of MODEL1934C/1944C/1954C/1964C Fastening the radiator to the radiator bracket Coating the antenna with silicone sealantFastening the radiator bracket to the antenna unit chassis Mounting the antenna unit Location of rubber matHow to fasten antenna unit to mounting platform Fixing the antenna unit chassisGround Using inside fixing holes of the antenna housing Antenna unit chassis, upper chassis separatedConnecting the signal cable Passing the signal cable through the cable gland assemblyAntenna unit chassis, cover opened How to fix signal cable in cable gland Torque 9.8 ±0.1 N .m Mounting the Power Supply Unit Model 1954C/1964C Power supply unit PSU-005 for Model 1954CPower supply unit Power supply unit PSU-008 for Model 1964C This page is intentionally left blank Standard Wiring 12-24 VDCDisplay unit, rear view Ground terminal Waterproofing cap and connector nut, sectional viewDJ-1 DATA1 to DATA4Radar Plotter Connecting GP-310B/320B to Data 2 portNetwork port Network sounderExternal Buzzer optional supply How to Connect with a PC MJ-A7SPF0007-050 cable connection for PCWiring the Power Supply Unit Model 1954C/1964C Power supply unit PSU-005 MODEL1954CPower supply unit, cover removed Power supply unit PSU-008 MODEL1964C CablingJumper block, slide switch setting Power supply unit, inside viewJumper block, slide switch Function Setting Power requirement, replacement of fuses Power requirementReplacement of fuses This page is intentionally left blank Setting up with the Installation Wizard Installation wizard, language selection windowInstallation wizard, units of measurement Installation wizard, network setupETR0 Installation wizard, radar setup Tuning Power Supply Unit for Model 1954C Examples of improper and correct sweep timing Wide Installation wizard, nav setup Wind AveragingNAV Setup menu description Furuno BB GPS GPS ReceiverGPS Setup menu description Description Settings Default SettingDescription Installation wizard, DATA1 GPS/NMEA port setup menu Waas setup requires GPS receiver GP-320B/330BContents of Waas Setup menu Installation wizard, DATA2 Nmea port setup menuInstallation wizard, port monitor display DATA2 portDATA4 port Installation wizard, Nmea sentence selection window Checking Magnetron Heater Voltage MODEL1824C MODEL1834CThis page is intentionally left blank Necessary parts Contents of ARP kitARP Kit ARP-11 Name Type Code No QtyDismounting the Power Board BoardOrder of fastening screws Connecting video equipment Contents of NTSC/PAL Interface kitName Type Code No Qty Remarks Cable 3C-2V, sectional view NTSC/PAL Interface Board attachmentCable ties attachment Display unit, passing the PIP cableConnecting an external monitor How to connect 15SDS/XHP10-005Necessary parts for external monitor Connecting remote display How to connect remote signal cableAttaching the cable tie to Power Board Attaching more than two units0%%5㨮0%#42%5  +/05+105+0&4#9+014440%10.#. 㨻㩧㩍㩏 +/05+105+0&4#9+014440%10. 工事材料表 257 000-155-827-10 Page Page Page Hatai ,WN4UWOK Page Page Marine Radar Model 1934C/1944C Model 1954C Model 1964C Color Video Plotter
Related manuals
Manual 239 pages 53.43 Kb Manual 10 pages 42.92 Kb
Top Page Image Contents