Multiquip operation manual MT-86D2TAMPING Rammer Basic Engine

Page 14

MT-86D2TAMPING RAMMER — BASIC ENGINE

Figure 2. Engine Controls and Components

The engine shown above is a YANMAR L48V6 engine (Figure 2). The engine must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer’s engine manual for instructions and details of operation and servicing. Each component is described below:

6.Recoil Starter– Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and smoothly.

7.Oil Filler Cap / Dipstick – Remove this cap to add oil to the engine crankcase. Read dipstick to determine if oil level is low. DO NOT over fill.

1.Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.

CAUTION - Fueling The Engine

Adding fuel to the tank should be done only

NOTE

Operating the engine without an air filter, with a damaged air filter, or a filter in need of replacement will allow dirt to enter the engine, causing rapid engine wear.

when the engine is stopped and has had an opportunity to cool down. In the event of a fuel spill, DO NOT attempt to start the engine until the fuel residue has been completely wiped up, and the area surrounding the engine is dry.

8.Oil Drain Plug – Unscrew plug to drain oil from engine crankcase. Dispose of oil in a safe manner.

9.Decompression Lever– Press down before starting engine.To prevent damage to engine, DO NOT use for any other purpose.

2.

Fuel Tank – Capacity is 3.5 quarts (3.31 liters) of diesel

 

fuel.

3.

Air Cleaner – Prevents dirt and other debris from entering

 

the fuel system. Remove wing-nut on top of air filter

 

cannister to gain access to filter element.

4.

Muffler – Used to reduce noise and emissions.

5. Recoil Starting Handle (pull rope) – Type of engine starting method.

CAUTION - Burn Hazard

Enginecomponentscangenerateextremeheat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operating. NEVER operate the engine with the muffler removed.

10.Fuel Cock– Controls the flow of diesel fuel to the carburetor. Must be in the ON position when starting and running the engine.

PAGE 14 — MT-86D2 TAMPING RAMMER — OPERATION AND PARTS MANUAL — REV. #3 (06/18/07)

Image 14
Contents Model MT-86D2 MT-86D2 Tamping Rammer Proposition 65WARNING Page MT-86D2 Tamping Rammer -TABLE of Contents Mikasa MT-86DBest Deal! Order via Internet Dealers Only Order via Fax Dealers OnlyMT-76D2TAMPING Rammer Safety Message Alert Symbols Foryour Safety and the Safety of OthersMT-76D2TAMPING Rammer Safety Message Alert Symbols Rotating Parts HazardsMT-86D2TAMPING Rammer Rules for Safe Operation Read this manualMT-86D2TAMPING Rammer Rules for Safe Operation TransportingMT-86D2TAMPING Rammer Operation and Safety Decals Construction of Tamping Rammer MT-86D2TAMPING Rammer General InformationDefinition of Tamping Rammer Rammer Gearbox and Spring CylinderMT-86D2TAMPING Rammer Specifications MT-86D2 Rammer SpecificationsMT-86D2TAMPING Rammer Controls and Components MT-86D2 Tamping RammerMT-86D2TAMPING Rammer Basic Engine MT-86D2TAMPING Rammer Initial START-UP EngineStarting Throttle LeverStopping the Engine MT-86D2TAMPING Rammer OperationOperation Daily Replacement of Lubricant EngineEngine Oil Replacement Interval Transportation MT-86D2TAMPING Rammer MaintenanceCleaning the Air Cleaner StorageMT-86D2TAMPING Rammer Troubleshooting Engine TroubleshootingRammer Troubleshooting Part NO. Column MT-86D2TAMPING Rammer Explanation of Parts SectionNO. Column QTY. ColumnMT-86D2TAMPING Rammer Suggested Spare Parts MT-86D2 Rammer withYanmar L48V6 EngineMT-86D2TAMPING Rammer Name Plate and Decals MT-86D2TAMPING Rammer Nameplate and Decals Part Name QTY RemarksMT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy Part Name QTYMT-86D2TAMPING Rammer Cylinder Guide and Foot Assy MT-86D2TAMPING Rammer Cylinder Guide and Foot Assy Ring G-95MT-86D2TAMPING Rammer -TANK and Handle Assy Part Name QTY Remarks Yanmar L-48V6 Engine Cylinder Block Assy Starter Cover Yanmar L-48V6 Engine Cylinder Head Assy Cylinder Head Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Piston Assy Piston Ring SET STD Yanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Yanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Bolt M 6X 12 PlatedYanmar L-48V6 Engine Cooling and Starting Assy Cooling & Starting Device Assy Yanmar L-48V6 Engine Fuel Injection Pump Assy Fuel Injection Pump Body Yanmar L-48V6 Engine AIR Cleaner Assy AIR Intake Pipe Yanmar L-48V6 Engine Muffler Assy Muffler Gasket Yanmar L-48V6 Engine TOOLS, Labels and Gasket SET Assy Yanmar Label Yanmar L-48V6 Engine Accessories Assy Hose 12.5 Band Payment Terms Page Heres HOW to GET Help