Multiquip operation manual MT-86D2TAMPING Rammer Operation, Stopping the Engine

Page 17

MT-86D2TAMPING RAMMER — OPERATION

Operation

1.Move the throttle lever quickly from the IDLE to OPERATION position to start tamping action. DO NOT move the throttle lever slowly as this may cause damage to the clutch or spring box.

CAUTION

The tamping rammer is designed to tamp the ground 700 times per minute at an engine speed of 3,300 rpm. Increasing the engine speed above the recommended rpm will not increase the rammer effectiveness. Impact will actually decrease because a resonance is created rather than a tamping effect, and damage to the unit can result.

2.The rammer can be warmed by quickly moving the throttle lever from the OPERATION to the IDLE position several times until the rammer operates smoothly.

3.The tamping rammer is designed to travel forward while tamping.To increase travel speed, pull back slightly on the handle so that the rear of the foot contacts the soil first.

4.To stop tamping, quickly move the throttle lever from the OPERATION to IDLE position.Do not move the lever slowly as irregular action and damage may result.

Stopping the Engine

1.Move throttle lever quickly from idle to STOP while pressing the throttle lever button. Run the engine for three minutes at idle speed to allow for proper cool down. Following the above procedures will prevent improper cylinder lubrication caused by a overheated engine. See Figure 8.

Figure 8. Stopping the Engine

MT-86D2 TAMPING RAMMER— OPERATION AND PARTS MANUAL — REV. #3 (06/18/07) — PAGE 17

Image 17

Contents Model MT-86D2 MT-86D2 Tamping Rammer Proposition 65WARNING Page Mikasa MT-86D MT-86D2 Tamping Rammer -TABLE of ContentsOrder via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyForyour Safety and the Safety of Others MT-76D2TAMPING Rammer Safety Message Alert SymbolsRotating Parts Hazards MT-76D2TAMPING Rammer Safety Message Alert SymbolsRead this manual MT-86D2TAMPING Rammer Rules for Safe OperationTransporting MT-86D2TAMPING Rammer Rules for Safe OperationMT-86D2TAMPING Rammer Operation and Safety Decals Definition of Tamping Rammer MT-86D2TAMPING Rammer General InformationConstruction of Tamping Rammer Rammer Gearbox and Spring CylinderMT-86D2 Rammer Specifications MT-86D2TAMPING Rammer SpecificationsMT-86D2 Tamping Rammer MT-86D2TAMPING Rammer Controls and ComponentsMT-86D2TAMPING Rammer Basic Engine Engine MT-86D2TAMPING Rammer Initial START-UPThrottle Lever StartingStopping the Engine MT-86D2TAMPING Rammer OperationOperation Daily Replacement of Lubricant EngineEngine Oil Replacement Interval Cleaning the Air Cleaner MT-86D2TAMPING Rammer MaintenanceTransportation StorageEngine Troubleshooting MT-86D2TAMPING Rammer TroubleshootingRammer Troubleshooting NO. Column MT-86D2TAMPING Rammer Explanation of Parts SectionPart NO. Column QTY. ColumnMT-86D2 Rammer withYanmar L48V6 Engine MT-86D2TAMPING Rammer Suggested Spare PartsMT-86D2TAMPING Rammer Name Plate and Decals Part Name QTY Remarks MT-86D2TAMPING Rammer Nameplate and DecalsMT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy Part Name QTY MT-86D2TAMPING Rammer Crankcase and Engine AssyMT-86D2TAMPING Rammer Cylinder Guide and Foot Assy Ring G-95 MT-86D2TAMPING Rammer Cylinder Guide and Foot AssyMT-86D2TAMPING Rammer -TANK and Handle Assy Part Name QTY Remarks Yanmar L-48V6 Engine Cylinder Block Assy Starter Cover Yanmar L-48V6 Engine Cylinder Head Assy Cylinder Head Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Piston Assy Piston Ring SET STD Yanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Bolt M 6X 12 Plated Yanmar L-48V6 Engine LUB. OIL Pump and Governor AssyYanmar L-48V6 Engine Cooling and Starting Assy Cooling & Starting Device Assy Yanmar L-48V6 Engine Fuel Injection Pump Assy Fuel Injection Pump Body Yanmar L-48V6 Engine AIR Cleaner Assy AIR Intake Pipe Yanmar L-48V6 Engine Muffler Assy Muffler Gasket Yanmar L-48V6 Engine TOOLS, Labels and Gasket SET Assy Yanmar Label Yanmar L-48V6 Engine Accessories Assy Hose 12.5 Band Payment Terms Page Heres HOW to GET Help