Multiquip operation manual MT-86D2TAMPING Rammer Initial START-UP, Engine

Page 15

MT-86D2TAMPING RAMMER — INITIAL START-UP

This section is intended to assist the operator with the initial start-up of the MT-86D2Tamping Rammer.It extremely important that this section be read carefully before attempting to operate the rammer.

DO NOT use your rammer until this section is thoroughly understood.

CAUTION	Read Manual
CAUTION

Failure to understand the operation of the MT-76D2Tamping Rammer could result in severe damage to the rammer or cause personal injury.

Rammer Gearbox and Spring Cylinder

This unit uses an oil bath lubrication system. Check oil level through oil level sight glass at rear of tamper foot. If oil is not visible, add #10W-30 motor oil. Oil bath contains approx. 1.7 pt. (800cc).

Engine

1. Fill the fuel tank with automobile diesel fuel (See Figure 3).

Figure 4. Oil Level

INSPECTION

1.Check all nuts, bolts and fasteners for tightness. Retighten as necessary.

2.Clean dirt from the recoil starter and foot. Wipe entire unit clean before operating.

3.Replace any missing or damaged Safety/Operation decals.

Figure 3. Fuel Tank

2.For checking the oil level, move the engine to vertical position and check that the oil is level with the oil inlet (about 700cc). See Figure 4.

MT-86D2 TAMPING RAMMER— OPERATION AND PARTS MANUAL — REV. #3 (06/18/07) — PAGE 15

Image 15

Contents Model MT-86D2 MT-86D2 Tamping Rammer Proposition 65WARNING Page Mikasa MT-86D MT-86D2 Tamping Rammer -TABLE of ContentsOrder via Fax Dealers Only Best Deal! Order via Internet Dealers OnlyForyour Safety and the Safety of Others MT-76D2TAMPING Rammer Safety Message Alert SymbolsRotating Parts Hazards MT-76D2TAMPING Rammer Safety Message Alert SymbolsRead this manual MT-86D2TAMPING Rammer Rules for Safe OperationTransporting MT-86D2TAMPING Rammer Rules for Safe OperationMT-86D2TAMPING Rammer Operation and Safety Decals Rammer Gearbox and Spring Cylinder MT-86D2TAMPING Rammer General InformationDefinition of Tamping Rammer Construction of Tamping RammerMT-86D2 Rammer Specifications MT-86D2TAMPING Rammer SpecificationsMT-86D2 Tamping Rammer MT-86D2TAMPING Rammer Controls and ComponentsMT-86D2TAMPING Rammer Basic Engine Engine MT-86D2TAMPING Rammer Initial START-UPThrottle Lever StartingMT-86D2TAMPING Rammer Operation OperationStopping the Engine Replacement of Lubricant Engine Engine Oil Replacement IntervalDaily Storage MT-86D2TAMPING Rammer MaintenanceCleaning the Air Cleaner TransportationEngine Troubleshooting MT-86D2TAMPING Rammer TroubleshootingRammer Troubleshooting QTY. Column MT-86D2TAMPING Rammer Explanation of Parts SectionNO. Column Part NO. ColumnMT-86D2 Rammer withYanmar L48V6 Engine MT-86D2TAMPING Rammer Suggested Spare PartsMT-86D2TAMPING Rammer Name Plate and Decals Part Name QTY Remarks MT-86D2TAMPING Rammer Nameplate and DecalsMT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy Part Name QTY MT-86D2TAMPING Rammer Crankcase and Engine AssyMT-86D2TAMPING Rammer Cylinder Guide and Foot Assy Ring G-95 MT-86D2TAMPING Rammer Cylinder Guide and Foot AssyMT-86D2TAMPING Rammer -TANK and Handle Assy Part Name QTY Remarks Yanmar L-48V6 Engine Cylinder Block Assy Starter Cover Yanmar L-48V6 Engine Cylinder Head Assy Cylinder Head Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Piston Assy Piston Ring SET STD Yanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Bolt M 6X 12 Plated Yanmar L-48V6 Engine LUB. OIL Pump and Governor AssyYanmar L-48V6 Engine Cooling and Starting Assy Cooling & Starting Device Assy Yanmar L-48V6 Engine Fuel Injection Pump Assy Fuel Injection Pump Body Yanmar L-48V6 Engine AIR Cleaner Assy AIR Intake Pipe Yanmar L-48V6 Engine Muffler Assy Muffler Gasket Yanmar L-48V6 Engine TOOLS, Labels and Gasket SET Assy Yanmar Label Yanmar L-48V6 Engine Accessories Assy Hose 12.5 Band Payment Terms Page Heres HOW to GET Help