Multiquip MT-86D2 operation manual MT-76D2TAMPING Rammer Safety Message Alert Symbols

Page 6

MT-76D2TAMPING RAMMER — SAFETY MESSAGE ALERT SYMBOLS

FORYOUR SAFETY AND THE SAFETY OF OTHERS!

Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.

This Owner's Manual has been developed to provide complete instructions for the safe and efficient

NOTE operation of the MQ Mikasa Model MT-86D2 Tamping Rammer. Refer to the engine manufacturer's instructions for data relative to its safe operation.

Before using this rammer, ensure that the operating individual has read and understood all instructions in this manual.

HAZARD SYMBOLS

Potential hazards associated with the operation of a MT-86D2Tamping Rammer will be referenced with Hazard Symbols which appear throughout this manual, and will be referenced in conjunction with Safety Message Alert Symbols.

WARNING Lethal Exhaust Gas Hazards

Engine exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. NEVER operate this equipment in a confined area or enclosed structure that does not provide ample free flow air.

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you about potential hazards that could injure you or others. The Safety Messages specifically address the level of exposure to the operator, and are preceded by one of three words: DANGER,

DANGER

You WILL be KILLED or SERIOUSLY INJURED

if you DO NOT follow these directions.

WARNING

You CAN be KILLED or SERIOUSLY INJURED if

you DO NOT follow these directions.

CAUTION

You CAN be INJURED if you DO NOT follow these directions.

WARNING Explosive Fuel Hazards

Fuel is extremely flammable, and its vapors can cause an explosion if ignited. DO NOT start the engine near spilled fuel or combustible fluids.

DO NOT fill the fuel tank while the engine is running or hot. DO NOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system. Store fuel in approved containers, in well-ventilated areas and away from sparks and flames.

 

WARNING

Burn Hazards

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operations. Never operate the engine with heat shields or heat guards removed.

 

WARNING

Respiratory Hazards

ALWAYS wear approved respiratory protection when required.

PAGE 6 — MT-86D2 TAMPING RAMMER — OPERATION AND PARTS MANUAL — REV. #3 (06/18/07)

Image 6
Contents Model MT-86D2 MT-86D2 Tamping Rammer Proposition 65WARNING Page MT-86D2 Tamping Rammer -TABLE of Contents Mikasa MT-86DBest Deal! Order via Internet Dealers Only Order via Fax Dealers OnlyMT-76D2TAMPING Rammer Safety Message Alert Symbols Foryour Safety and the Safety of OthersMT-76D2TAMPING Rammer Safety Message Alert Symbols Rotating Parts HazardsMT-86D2TAMPING Rammer Rules for Safe Operation Read this manualMT-86D2TAMPING Rammer Rules for Safe Operation TransportingMT-86D2TAMPING Rammer Operation and Safety Decals Construction of Tamping Rammer MT-86D2TAMPING Rammer General InformationDefinition of Tamping Rammer Rammer Gearbox and Spring CylinderMT-86D2TAMPING Rammer Specifications MT-86D2 Rammer SpecificationsMT-86D2TAMPING Rammer Controls and Components MT-86D2 Tamping RammerMT-86D2TAMPING Rammer Basic Engine MT-86D2TAMPING Rammer Initial START-UP EngineStarting Throttle LeverMT-86D2TAMPING Rammer Operation OperationStopping the Engine Replacement of Lubricant Engine Engine Oil Replacement IntervalDaily Transportation MT-86D2TAMPING Rammer MaintenanceCleaning the Air Cleaner StorageMT-86D2TAMPING Rammer Troubleshooting Engine TroubleshootingRammer Troubleshooting Part NO. Column MT-86D2TAMPING Rammer Explanation of Parts SectionNO. Column QTY. ColumnMT-86D2TAMPING Rammer Suggested Spare Parts MT-86D2 Rammer withYanmar L48V6 EngineMT-86D2TAMPING Rammer Name Plate and Decals MT-86D2TAMPING Rammer Nameplate and Decals Part Name QTY RemarksMT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy MT-86D2TAMPING Rammer Crankcase and Engine Assy Part Name QTYMT-86D2TAMPING Rammer Cylinder Guide and Foot Assy MT-86D2TAMPING Rammer Cylinder Guide and Foot Assy Ring G-95MT-86D2TAMPING Rammer -TANK and Handle Assy Part Name QTY Remarks Yanmar L-48V6 Engine Cylinder Block Assy Starter Cover Yanmar L-48V6 Engine Cylinder Head Assy Cylinder Head Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Crankshaft and Camshaft Assy Yanmar L-48V6 Engine Piston Assy Piston Ring SET STD Yanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Yanmar L-48V6 Engine LUB. OIL Pump and Governor Assy Bolt M 6X 12 PlatedYanmar L-48V6 Engine Cooling and Starting Assy Cooling & Starting Device Assy Yanmar L-48V6 Engine Fuel Injection Pump Assy Fuel Injection Pump Body Yanmar L-48V6 Engine AIR Cleaner Assy AIR Intake Pipe Yanmar L-48V6 Engine Muffler Assy Muffler Gasket Yanmar L-48V6 Engine TOOLS, Labels and Gasket SET Assy Yanmar Label Yanmar L-48V6 Engine Accessories Assy Hose 12.5 Band Payment Terms Page Heres HOW to GET Help