Installation, Operating Instructions | Ingersoll-Rand 650531-1

INSTALLATION

The 65053X-X Chop-Check Dispensing System comes completely assembled. Remove unit from crate and place on a level surface. Install material hose and dispensing device as required.

When the following instructions are observed, heavy paste materials can be pumped directly from their original 5 gallon drum without air in.

clusion, or excessive waste. The follower plate creates an air tight seal as well as clean-wiping action in its progressive downward movement into the drum.

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS / INITIAL SETUP PROCEDURE

WARNING STAND CLEAR. When raising or lowering the

2	lift.
	AIR CONTROLS
		PUMP AIR
	PUMP AIR	REGULATOR
	PUMP AIR
	INLET
	CART/LIFT
	AIR INLET
	OFF	ON
	OFF
	FOLLOWER PLATE
	AIR SUPPLY VALVE
		FIGURE 2

TO RAISE LIFT, (THE FIRST TIME):

1.Take note of the pump/drum clearance above. Be certain the lift is clear of any objects above the unit.

2.Adjust (Turn Needle Valve Knob Counter-Clockwise) air pressure to lift. Connect the air supply (160 PSI MAX) to the air inlet.

3.Raise the lift high enough to clear the height of the drum. Stop the lift upward travel by adjusting (Turn Needle Valve Clockwise until tight.) Needle Valve.

stops on the base to center 5 gallon drum. Tighten thumb screw to secure drum.

2.Lubricate lower follower wiper plate seal with any type grease. (sili. cone, vaseline, gear, etc.) This ensures a smooth fit into the pail as well as prevents curing type compounds from bonding to seal.

3.Check vent plug on follower plate to be sure it easily threads in and out. It is recommended to lubricate the threads of the plug to help prevent possible set up of compound at this point. See 65184X-X Operator's Manual.

TO LOWER LIFT:

WARNING PINCH HAZARD. Follower can descend quickly causing injury. Keep hands clear when aligning with contain& er.

NOTE: Be certain the Follower Plate vent plug has been removed so that the air trapped between the follower and the material is allowed to escape from this vent. Captured air between the follower plate and drum will escape.

NOTE: The lift may hesitate momentarily before starting downward, the air pressure inside the post air chamber must decrease before it will begin to descend.

1.Disconnect air line from the lift air inlet. Adjust (Turn Needle Valve Knob Counter-Clockwise) Needle Valve to Lower the pump end into drum.

2.Replace the vent plug once the material begins to ooze from the vent opening.

3.Adjust (Turn pump air regulator knob Counter-Clockwise to prevent over pressurization of pump.) Knob on pump air regulator.

4.Connect air line to pump air regulator and adjust (Turn pump air regu. lator Clockwise) air until pump begins to cycle.

5.Trigger gun to prime pump with material.

TO RAISE LIFT, (NORMAL OPERATION):

1.Disconnect air line from pump air regulator and connect to lift air inlet. Adjust the Follower Plate Air Valve pressure up to approxi. mately 8 psig. DO NO OVERPRESSURIZE THE DRUM to avoid damage.

NOTE: Air from this valve will only pass when the unit is being raised.

2.Adjust (Turn Needle Valve Knob Counter-Clockwise) air pressure on lift.

3.Raise the lift high enough to clear the height of the drum. Stop the lift upward travel adjusting needle valve knob Counter-Clockwise.

TO CHANGE DRUM:

NOTE: The Needle Valve Knob should be turned Clockwise to hold lift in the ``UP" Position.

1.Unsrew thumb screw and remove old 5 gallon drum.

2.Place and center. a new drum into position. Remove cover. Tight. en thumb screw.

REFER TO PAGE 3:

1.Once lift assembly and pump are in the ``UP" position, place and center an opened 5 gallon drum of material on the lift base. Use the

PAGE 2 OF 4

650531-1, 650530-1 specifications

Ingersoll-Rand is a renowned name in the manufacturing industry, known for producing high-quality tools and equipment. Among their impressive lineup, the models 650530-1 and 650531-1 stand out for their unique features and advanced technologies that cater to both professionals and DIY enthusiasts.

The Ingersoll-Rand 650530-1 is an air impact wrench designed specifically for high-torque applications. One of its main features is the powerful motor that delivers a staggering air torque output, making it extremely effective in loosening tight bolts and nuts. This robust performance is complemented by an ergonomic design that ensures user comfort, reducing fatigue during prolonged use. The 650530-1 also boasts a lightweight aluminum housing, which not only contributes to its durability but also makes it easier to handle, especially in overhead applications.

On the other hand, the Ingersoll-Rand 650531-1 is an upgraded version that enhances several key aspects of its predecessor. This model also focuses on high-torque performance but integrates advanced technologies for improved efficiency and control. One of its notable features is the built-in regulator that allows users to adjust the torque output according to their specific needs. This versatility makes the 650531-1 suitable for a wide range of tasks, from automotive repairs to heavy-duty construction work.

Both models incorporate an innovative air inlet design that ensures quick and efficient airflow, optimizing performance while minimizing energy consumption. Additionally, they are equipped with a durable motor that ensures longevity and reduces the frequency of maintenance issues. The materials used in their construction are not only robust but also resistant to wear and tear, which is essential in high-demand environments.

Ingersoll-Rand's commitment to safety is evident in the design of both tools. They feature easy-to-use finger-tip trigger controls and protective rubber grips that enhance user control and comfort. Moreover, they include mechanisms to reduce vibration, which further improves handling and reduces the risk of strain injuries.

Overall, the Ingersoll-Rand 650530-1 and 650531-1 models represent a significant advancement in air tool technology, combining power, efficiency, and user-centric design. Whether for professional workshops or home garages, these tools are engineered to meet the demands of a variety of applications, providing reliable and effective performance that professionals trust.