Graco 206700, 206699, 206405 Reassembly, 30 31 34 † 33 † 45 † 32 † 58 53† 33† 45†

Page 14

Air Motor Service

M2

30 31 37

54

28

3

 

34

L

 

33

 

 

45

 

 

32

1

59

55

58 533345

1 To remove toggles: push in, swing up, ease out.

2Push toggles (M) in and then up (shown in down position).

3Turn wires up.

04118

Fig. 7

10.Remove the lockwires (34) from the adjusting nuts (33) of the transfer valves. Screw the top nuts off. Screw the poppet valve stems (45) out of the grommets (32) and the bottom nuts (30). Take the valve poppets off the stems and squeeze them firmly to check for cracks. See Fig. 7.

WARNING

To reduce the risk of pinching or amputating your fingers, always keep fingers clear of the toggle assemblies (M).

11.Grip the pivot pins (30) with pliers. Compress the springs (31), and swing the toggle assembly (M) up and away from the piston lugs (L). Remove the parts. Check to see that the valve actuator (35) is supported by the spring clips (58) but slides easily into them. See Fig. 7.

12.Remove the trip rod yoke (28), actuator (35) and trip rod (54). See Fig. 7. Check the exhaust valve poppets (53) for cracks. To remove the exhaust valve poppets (53), stretch them out and cut them with a sharp knife.

13.Remove one muffler plate (20 or 40). Pull the piston (59) up out of the base. Remove the throat packing nut (42) and packings. See Fig. 6.

541

58

53

 

45

35

33

32

33

36

0.145” (3.7 mm)

45

59

Cutaway View

1Cut off tops of poppets as indicated by dotted lines.

04119

Fig. 8

Reassembly

1.Clean all the parts in a compatible solvent and inspect for wear or damage. Check the polished surfaces of the piston (59), piston rod (41), and cylinder wall (51) for scratches or wear. A scored rod will cause premature packing wear and leak- ing. Use all the repair kit parts and replace other parts as necessary.

2.Lubricate all parts with a light, waterproof grease.

3.One at a time, install these parts in the base (55): the gland (49*), five v-packings (48*) with lips facing down, bearing (50*), backup washer (43), flat packing (44*), and loosely screw in the packing nut (42). Be sure the o-rings (38 & 39) are in place. See Fig. 6.

4.Pull the exhaust valve poppets (53) into the valve actuator (35) and clip off the top part shown with dotted lines. See Fig. 8.

5.Install the grommets (32) in the valve actuator (35). Install the trip rod (54) in the piston (59). Place the trip rod yoke (28) and valve actuator (35) on the trip rod. Be sure the o-ring (36*) is in place and that the valve actuator is supported by the spring clips (58), and reassemble the valve mechanism. See Fig. 7.

14 306531Z1

Image 14
Contents Instructions-Parts List Table of ContentsSymbols Equipment Misuse HazardSkin Injection Hazard Fire and Explosion Hazard 306531Z1 Installation System AccessoriesGrounding To ground the pumpOperation Pressure Relief ProcedureStarting and Adjusting the Pump 306531Z1 Flushing MaintenanceShutdown and General Care LubricationPacking Nut Adjustment Troubleshooting Problem Cause SolutionBefore you start Air Motor ServiceAir Motor & Throat Disassembly Reassembly 30 31 34 † 33 † 45 † 32 † 58 53† 33† 45†Air Motor Service Displacement Pump Service Displacement Pump DisassemblyDisplacement Pump Service Parts Model 206405, Series K 35 lb. pail size 20 306531Z1 Model 206699, Series J 120 lb. drum size 22 306531Z1 Mounting Hole Layout DimensionsTechnical Data Graco Standard Warranty Graco Phone Numbers