ACR Electronics RLB-36, Y1-03-0233 manual To remove the expired HRU, To install the new HRU

Page 25

To remove the expired HRU

When opening the SeaShelter3™ lid, note that the beacon is installed with the lanyard face in. Pull the beacon with steady pressure from the bracket. Do not get beacon wet while out of bracket. The HRU has a keying feature that locks it to the bracket. If you view the HRU rod as the center of a clock, a properly installed HRU will rest at the 7 o’clock position, as shown in the picture above.

WARNING: The HRU holds down an ejection spring. The spring must be

held in place during the removal and installation of the HydroFix™ to prevent injury.

Depress the top of the ejection spring. This will relieve pressure on the HRU and allow it to be rotated counterclockwise to the 5 o’clock position. The HRU is now free to be removed. Slowly relieve pressure from the ejection spring and allow it to deploy.

WARNING: Discard the expired HRU. Failure to replace the entire assembly may cause the bracket to malfunction.

WARNING: Be sure to use only ACR’s HydroFix™ HRU (ACR P/N 9490)

in the SeaShelter3™. Use of unauthorized replacement parts will void your warranty and may cause the bracket to malfunction.

Check the date of manufacture on the new HRU. Follow the instructions that accompany the HydroFix™ for marking the next expiry date and for selecting the correct rod adapter for the SeaShelter3™.

To install the new HRU

Apply pressure to the ejection spring and hold it flat against the bracket. With your free hand place the new HRU into the key way in the 5 o’clock position and rotate clockwise to the 7 o’clock position. Slowly remove pressure from the ejection spring. The HRU should now be held in the 7 o’clock position with the pressure on the ejection spring.

Reinstall the beacon with lanyard face in. Beacon should fit snugly in the bracket with the antenna captured by the bracket. Reinstall the lid by seating the bottom of the lid to the detent on the base. Close the upper portion of the lid so the HRU rod lines up with the spring loaded knob. With gentle pressure, hold the lid while you turn the lock counterclockwise until it stops, then clockwise until it stops. This should capture the HRU and snap the lid into a locked position. Confirm that the lid is attached to the bottom of the bracket and the HRU.

CAUTION: Do not force the lid closed. If the lid does not close easily,

check to see that the beacon is properly installed in the bracket and the HydroFix™ is properly seated.

Y1-03-0233 Rev. D

24

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Owner Vessel Radio Call Sign UIN # Page Table of Contents Step ONE Registering Your Beacon How do I register? What country should I register in?Noaa Sarsat Beacon Registration Suitland Road Suitland, MDDo I need a radio license? How your beacon brings help Step TWO HOW the Beacon WorksExternal GPS interface Anatomy of your beacon Activation switch with Witness TabInternal GPS engine Top View Switch PositionsCategory 2 LowPro3 Bracket Category 1 SeaShelter3 BracketGPS √ Digital DisplayActivating your beacon Y1-03-0233 Rev. D Y1-03-0233 Rev. D Turning off the beacon False alarmsY1-03-0233 Rev. D Mounting location Step Three Installing the BeaconPage Category I bracket Category II bracket Installing the optical interface to an external GPS receiver Battery replacement Routine beacon maintenance Step Four Maintaining the Beacon On a routine basis aboard ship, doY1-03-0233 Rev. D Servicing the SeaShelter3 and the HydroFix HRU Changing ownership or contact informationTo remove the expired HRU To install the new HRUServicing the LowPro3 Self-Testing the beaconExtended GPS test Using the external GPS interface Appendix a Using and Testing the GPS SystemsTesting the external GPS interface How the external GPS interface worksLED indication of GPS fix Internal GPS position systemCompatible GPS receivers Appendix B User Interface Special IconsAppendix C User Interface Digital Display During Operation GPS Weak Give Clear View SKY GPS Data XX.XXX’Keep Epirb Right Leave Epirb Until RES QBatt Appendix D User Interface Digital Display During SELF-TESTBoard Test √ Board Test GPS Test  GPS Test √Light Test √ Light Test See User Book Self Test FailSeek FIX NOW Batt LOWGPS Test Long GPS Data Test StartTest END English French Spanish German Italian Phrases Appendix F- User Interface Language TranslationsGeneral overview Appendix G the COSPAS-SARSAT SystemGENERAL/ Environmental Appendix H Technical SpecificationsLimited Warranty Appendix I WARRANTY, Useful Life POLICY, Notices0735 EC Declaration of ConformityRepresentative International Maritime Organization Shore Based Maintenance

Y1-03-0233, RLB-36 specifications

The ACR Electronics RLB-36, identified by model number Y1-03-0233, is a remarkable beacon that exemplifies state-of-the-art survival technology designed for maritime, aviation, and outdoor enthusiasts. It represents a commitment to safety and reliability when it matters most.

One primary feature of the RLB-36 is its powerful strobe light, which emits a bright signal visible from considerable distances, making it an essential device for emergency signaling. The high-intensity LED strobe operates in various lighting conditions, ensuring visibility day or night. With a robust construction that withstands harsh environments, the RLB-36 is built to last, offering peace of mind to users who may find themselves in perilous situations.

The RLB-36 is designed with advanced technologies aimed at enhancing user experience and functionality. It includes features like Global Positioning System (GPS) integration, which allows for precise location tracking, an invaluable asset during rescue operations. The device can send out distress signals that include location data, expediting search and rescue efforts significantly.

Additionally, the RLB-36 has a user-friendly interface, allowing for quick activation in emergencies. The device is lightweight and compact, making it easily portable, which is crucial for those who venture into remote areas for activities such as boating, hiking, or flying. Its durable design also includes waterproof capabilities, effectively protecting it from the elements.

Another noteworthy characteristic of the RLB-36 is its long battery life. It utilizes efficient power management technology, ensuring that it remains operational for extended periods, crucial in emergencies when time is of the essence. The device is also equipped with a maintenance-free design, which means users can rely on its readiness without frequent checks or upkeep.

In summary, the ACR Electronics RLB-36, model Y1-03-0233, is not just a beacon; it is a lifeline defined by cutting-edge technology and rugged design. Its array of features—including a powerful strobe, GPS integration, lightweight construction, waterproof capabilities, and extended battery life—places it at the forefront of emergency signaling devices. Whether in the wilderness or out at sea, the RLB-36 ensures that help is never too far away.
Top Page Image Contents