Tascam 424MKIII owner manual Introduction, Portastudio 424 Mkiii is, About the weld line

Page 4

Introduction

The PORTASTUDIO 424 MKIII is...

The PORTASTUDIO 424 MKIII is a 4-track "Multitrack Master" cassette tape recorder and a full-function mixer with 8 inputs/stereo outputs combined into a single workstation.

Its high audio quality and creative flexibility reflect the experience and innovation that have allowed TASCAM to earn its reputation in professional audio production fields, and its user- friendly design makes the 424 MKIII suitable for anyone, from expert to novice.

Using this manual : To get the most out of your 424 MKIII, please take the time to read through this manual. Some time spent now will keep you from overlooking some of the features that make the 424 MKIII a more creative tool. You may discover some new tricks you haven't tried before.

Use of capital letters : In general, we use all upper case type to designate a particular switch, control, jack name or label (like PAN). Transport modes and some features are described with an upper case first letter (like Record mode).

CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT

ATTENTION : POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND.

NOTE FOR U.K. CUSTOMERS

DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

If nonetheless the mains plug is cut off, remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply.

If this product is not provided with a mains plug, or one has to be fitted, then follow the instructions given below:

IMPORTANT. DO NOT make any connection to the larger terminal which is marked with the letter E or by the safety earth symbol • or coloured GREEN or GREEN-and-YELLOW.

The wires in the mains lead on this product are coloured in accordance with the following code:

BLUE: NEUTRAL

BROWN: LIVE

About the weld line

There is a patterned stripe-like effect on the bottom surface of the 424 unit. This effect is called a "weld line" and is a natural result of the resin molding process employed in the manufacture of the 424 unit. It is not a crack or scratch, and will cause no problems with the operation of the 424 unit.

As these colours may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

When replacing the fuse only a correctly rated approved type should be used and be sure to re- fit the fuse cover.

IF IN DOUBT — CONSULT A COMPETENT ELECTRICIAN.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 424@$ Table Of Contents Safety Instructions Portastudio 424 Mkiii is IntroductionAbout the weld line Recording System Three Steps to MultitrackSignal Flow in the 424 Mkiii Mixer Understanding the MixerTape Cue Monitor System Multitrack Cassette Recorder RehearsalTape Speed and Track Format Track Format and Tape RecommendationsTape Type Accidental Erase/Record Protection Tape LengthPortastudio 424 Mkiii Brief Guide Portastudio 424 Mkiii Brief Guide Recorder Controls Rear Panel ConnectionsStep-By-Step-Operations Guide Page Page Tape CUE Page How to record many sources onto a single track How to record a mix onto two tracks simultaneously Recording on more than two tracks simultaneously Direct Page Using channels 5 and 6 with alternative inputs at mixdown Review Record levelLoading Memo points Using Memory Location PointsMemo Locating the tape To zero To Memo Auto play Operating procedure To interrupt Repeat sequence Repeat PlayPUNCH-IN or Insert Recording Preliminary Selecting in and out pointsPage Actual Auto Punch In/Out Auto Review Manual Punch-in Punching-in/out with RecordUsing the remote footswitch RC-30P Ping-pong procedure Bouncing Tracks Ping-PongPage Setting the output level of effect devices Using Effects With the Portastudio 424 MkiiiSetting the mix/balance control on effect devices How to Connect Your Effects Devices Syncing MIDI-Tape−Using the Tascam MTS-30 TroubleshootingProblem Possible Cause Problem SolutionFeatures and Controls Power switch on the rear panel TurnsInput select switches Channels Channels 5Stereo Input Section Mkiii Recorder Transport Controls Play keyDisplays Page Optional Accessories Care and Maintenance CleaningCleaning the Heads and Tape Guides Degaussing DemagnetizingCleaning the Pinch Roller Cleaning the Capstan ShaftHow the dbx Works Degaussing the Tape PathSpecifications High Effect 2 SEND/TAPE CUE OUTNormal Europe USA/CANADAAustralia Block Diagram Level Diagram 424@$
Top Page Image Contents