Akai MPK88, MPK61 manual Editing Footswitch Pedal Inputs, Control Change Parameters

Page 33

EDITING FOOTSWITCH PEDAL INPUTS

The footswitch inputs on the rear of the MPK61/MPK88 can be used in a variety of different ways. For example, footswitches can be used as a conventional MIDI CC switches. In addition, footswitches may be used to trigger specific pads on the top panel (for example, to play out a kick drum sequence). Lastly, footswitches may be used to remotely enable and disable specific functions on the MPK61/MPK88, such as Note Repeat, Time Division, Tap Tempo, Bank Change, Play/Stop, Arp On/Off, Arp Latch, Play/Record or Sustain.

1.To edit footswitch input settings, press [EDIT] to enter Edit Mode.

2.Now press down on the footswitch to select it for editing.

3.You will see Page 1 displayed on the screen (shown on the left).

4.Select the event type for the footswitch by turning the [VALUE] dial.

5.Press [ENTER] to accept change and view page 2 parameters, if available.

SELECT FOOTSWITCH EVENT TYPE

CONTROL CHANGE PARAMETERS

The following parameters can be accessed is you select “Control Change” as the footswitch event type.

MIDI CHANNEL FIELD

MIDI PORT/CHANNEL FIELD

This field sets the MIDI Port and Channel which the footswitch will use to transmit messages. You can assign the footswitch to one of two MIDI Ports, A or B, and to one of 16 MIDI Channels on each port (i.e. A14). You can also assign the footswitch to use the MIDI Common Channel.

1.Press [<] to select MIDI Port/Channel field.

2.While in MIDI Port/Channel field, use [VALUE] dial to select desired MIDI Port and Channel.

3.Press [>] button to select the next field.

Note: When not used via USB, only footswitch messages assigned to port A will be transmitted via the 5-pin MIDI port on the back of the MPK61/MPK88.

CONTROL CHANGE FIELD

In this field you can set which Control Change Number the footswitch will transmit when it is pressed.

1.Use [<] or [>] to select Control Change field.

2.While in Control Change field, use [VALUE] dial to select desired Control Change Number.

3.Press [>] button to select the next field.

CONTROL CHANGE FIELD

PLAY MODE

Here, you can select whether the footswitch transmits MIDI CC information in a momentary (MOM) way, where pressing the footswitch outputs 127 and releasing it transmits 0, or in a toggle (TGL) way where the first press outputs 127 and the second press transmits 0.

1.Press [>] to select Play Mode field.

2.While in Play Mode field, use [VALUE] dial to select desired Play Mode.

PLAY MODE FIELD

When finished editing, press [ENTER] to save or [<] to cancel the changes.

30

Image 33
Contents Operators Manual Page Table of Contents 6 7 8 Front Panel OverviewLevel When 16 Level Rear Panel Overview Hookup DiagramUSB cable not connected USB cable connectedOctave and Transposition Displaying InformationControl Aftertouch About Modes Preset ModeWhat is a Preset? Preset ModeNavigating Edit Mode Edit ModeController Selected Edit Mode ParametersKeyboard Octave Editing the KeyboardKeyboard Aftertouch Keyboard VelocityEditing the Pads What is a Note Message ? What is a Program Change ?Play Mode Field Midi Channel FieldPressure Behavior Program Change Field Program Change ParametersBank M Field Bank L FieldWhat is Control Change? What is Aftertouch?Editing Knobs and Faders Control Change Field Control Change ParametersMinimum Range Field Maximum Range FieldAftertouch Parameters INCREMENT/DECREMENT Parameters knobs only Editing Buttons Play ModeProgram Change Parameters Editing the Arpeggiator Button Mode Arpeggio Parameters TYPE, RANGE, Button ModeARP Type RangeArpeggio Parameters GATE, Swing GateSwing Please note Editing Note RepeatGate Field Editing Time Division Default Time DivisionEditing the Pitch Bend Wheel Midi Channel Editing the Modulation WheelMidi CC Minimum ValueEditing TAP Tempo Editingmaximum Value Transport ControlEditing Footswitch Pedal Inputs Editing Expression Pedal Input Drum PAD ParametersOther Functions Editing Split Split PointSplit Parameters Kill Midi Page1 Global ModeKeyboard Velocity Curve PAD Threshold SysEx transfers to the MPK61/MPK88 Save GlobalProg Change Program Change Program Change ModeFrequently Asked Questions Troubleshooting Email support@akaipro.com TEL 401.658.4032 U.S Technical Specifications51-0296-B