Roland 5 manual Command 02h Set Europas base Midi channel

Page 66

Europa MIDI Implementation					Europa User Guide


		Byte #	Value	Description
		0	01h	Reset the Jupiter 6’s NVRAM and Europa’s internal flash to factory patch/preset
				settings
		1	4ah
		2	36h

Figure 17 - Command 01h - Reset NVRAM and Europa's internal flash to factory patch/preset settings

This will write factory Europa board settings to the Jupiter 6’s NVRAM. It will not write factory patches or presets back to NVRAM – only Europa board settings. This command will not have any effect if the memory protect switch is on.


	Byte #	Value	Description
	0	02h	Set Europa’s base MIDI channel
	1	00h-0fh	Base MIDI channel desired. All other values ignored.

Figure 18 - Command 02h - Set Europa's base MIDI channel

Sets Europa’s base MIDI channel. The new MIDI channel is retained across board power cycles. This command will not have any effect if the memory protect switch is on.


	Byte #	Value	Description
	0	03h	Generate a random patch on one of the SPLITS
	1	00h-7fh	00h=Random patch is generated on lower SPLIT, non-00h=Random patch is
			generated on the upper SPLIT (upper SPLIT used when in WHOLE mode)

			Figure 19 - Command 03h - Generate random patch

Generates a random patch on either of the key mode SPLITS. The patch edit buffer is modified and the voice boards are set to the newly randomized patch. If the board is set to whole mode and a random patch is created for the lower voice, the lower patch edit is modified but is not heard. Setting the board in either SPLIT mode will allow the randomized lower patch to be heard. The upper patch is used for whole mode.


	Byte #	Value	Description
	0	04h	Request a patch, preset, or sequence dump
	1	Bitwise	Bit 7	Unused – set to 0
			Bits 6-4 Block dump type:
				000	– Dump patch
				001	– Dump preset
				010	– Reserved – not valid
				011	– Rhythm/sequence
				100	– Board state – All settings, patches, and presets – everything!
				101-111 – Not valid - Command will be ignored
			Bits 3-0 Unused – set to 0 (other values will invalidate the message and it
				will be ignored).
	2	Varies	Dump patch (000 on bits 6-4):
		depending		00h-2fh – Dump patches A-1through F-8from flash
		on block		30h-7ch – Invalid (command will be ignored)
		dump		7dh	- Dump all patches from flash (xmit delays included)
		type value		7eh	- Dump lower patch edit
		in byte 1		7fh	- Dump upper patch edit

Page 66

Image 66

Contents Page Trademarks Europa User Guide Table Of Contents What’s on discTable Of Contents Europa User Guide Voice assignment modesCommon problems Boot block EuropaArpeggiator mode and options when the UP button is Held Arpeggiator step rhythm programming buttonsEuropa User Guide Terminology and symbols Introduction Europa User Guide Bold TapeNew feature summary Europa User Guide Additional arpeggiator modesEuropa User Guide New feature summary What is not included Europa User Guide Operational differences Arpeggiator, voice, and synchronization structureOperational differences Europa User Guide Additional voice assignment modes Power up diagnostics and actions Europa User Guide Power up diagnosticsEuropa User Guide Power up diagnostics and actions To F-5 Europa boot and diagnostic flowchart Internal CPU Xram is tested Jig mode is tested Tape Button is testedInternal CPU stack RAM is tested External scratch RAM is testedWrite + Tape BenderSetting the Jupiter 6’s base Midi channel Selection Base Midi channelLED on LED BlinkingLED Off C D E F Aftertouch assign LFO Delay Manual Cross MOD VCO 1 Range VCA LFOENV-1 Key track ENV-2 Key track Europa User Guide Voice assignment modes Solo Solo assign LED lit solidVoice assignment modes Europa User Guide Whole SplitPoly 2 steal Poly 2 LED blinking Arpeggiator Europa User Guide Europa User GuideArpeggiator Midi Clock Europa User Guide Arpeggiator Sources of notes to be played and keyboard/MIDI interactionArpeggio note List Sequence note Arpeggio note calculator takes the note to play Internal clock a Arpeggiator mode and options when the UP button is held Random mode Sequence modes and options E F G a BRecording a sequence Arpeggiator step rhythm programming buttons Europa User Guide Arpeggiator How do I……..? Europa User Guide Transfer patches from tape to Europa?Europa User Guide How do I……..? Save all patches and presets to MIDI? Europa User Guide Common problems Can’t get any sound out of Europa from the local keyboardCommon problems Europa User Guide Hear unplayed or missing notes in my arpeggiations Arpeggiator runs too fast/slow or doesn’t stay in sync Europa User Guide Europa Firmware Update Utility Windows firmware update utilityEuropa Firmware Update Utility Europa User Guide Locate an image to update Update the Jupiter Apple Macintosh Europa Firmware Update Utility Locate an image to update Update the Jupiter Europa Midi Implementation Europa User Guide Basic Midi functionalityEuropa User Guide Europa Midi Implementation IDI MessageLFO =LOWER SPLIT, 127=UPPER SplitVCO MOD ENVVCO Mixer VCF LFOVCA ENV Unison PWMVCO Lower Upper KEY ModeLOWER/UPPE Lower SPLIT, 127= Upper SplitEuropa Midi Implementation Europa User Guide Europas Continuous Controller map BPM F0h Command 02h Set Europas base Midi channel Europa User GuideEuropa Midi Implementation VCO MOD LFOVCF LFO 1 mod VCO MOD ENVXmod Manual VCA ENV 2 LevelPWM LFO Europa Midi Implementation Europa User Guide UPPER/WHOLE Upper /WHOLEA1-F8 Whole Upper Whole LowerCommand 07h Assign controller F0h 41h 10h 4ah 36h 00h 68h 36h f7h Boot block Europa User Guide Europa Internal ArchitectureContact Information Europa User Guide Visit Synthcom on the internetEuropa User Guide Europa Limited Warranty User installed Europa upgradesEuropa Limited Warranty Europa User Guide Acknowledgements Europa User Guide AcknowledgementsArpeggiator mode and options when the UP button is held Europa supermode reference sheet