Pioneer VSX-72TXV, VSX-74TXVI Minute guide, Playing a source, Better sound using Phase Control

5 minute guide 02

Problems when using the Auto MCACC Setup

If the room environment is not optimal for the Auto MCACC Setup (too much background noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary. If there are any instructions showing in the front panel display, please follow them.

•Some older TVs may interfere with the operation of the microphone. If this seems to be happening, switch off the TV when doing the Auto MCACC Setup.

Playing a source

Here are the basic instructions for playing a source (such as a DVD disc) with your home theater system.

				GUIDE
					TV CONTROL
				TV VOL	INPUT	TV CH	VOL
					SELECT
	INPUT		SYSTEM OFF
RECEIVER			SOURCE
	SELECT				REC	DTV INFO	MUTE
				MPX		REC STOP	MEMORY
				AUDIO	SUBTITLE	HDD	DVD
				DISP		CH	CH
				STATUS	SIGNAL SEL	SBch	STEREO
CD	TV	VIDEO 2		MULTI OPE	THX	STANDARD	ADV. SURR
DVD	SAT	VIDEO1	TVCONT
DVR2	CD-R	XMRADIO	ROOM2/3	SHIFT	PHASE	MCACC	S.DIRECT
DVR1	iPod	TUNER	RECEIVER

4Use the volume control to adjust the volume level. Turn down the volume of your TV so that all sound is coming from the speakers connected to this receiver.

Better sound using Phase Control

This receiver’s Phase Control feature uses phase correction measures to make sure your sound source arrives at the listening position in phase, preventing unwanted distortion and/or coloring of the sound (see illustration below).

P		Front speaker	Listening
H			position
A
S
E			?
C
O
N
T
O	Sound
F		Subwoofer
F	source
P		Front speaker	Listening
			position
H
A
S
E

C

O

N

T

OSound

N source Subwoofer

1Switch on your system components and receiver. Start by switching on the playback component (for

example a DVD player), your TV1 and subwoofer (if you have one), then the receiver (press RECEIVER).

• Make sure the setup mic is disconnected.

2 Select the input source you want to play.

You can use the input source buttons on the remote control, INPUT SELECT, or the front panel INPUT

SELECTOR dial.2

3 Press S. DIRECT (STREAM DIRECT) to select ‘AUTO SURROUND’ and start playback of the source.3

If you’re playing a Dolby Digital or DTS surround sound DVD disc, you should hear surround sound. If you are playing a stereo source, you will only hear sound from the front left/right speakers in the default listening mode.

•See also Listening to your system on page 26 for information on different ways of listening to sources.

Phase Control technology provides coherent sound

reproduction through the use of phase matching4 for an optimal sound image at your listening position. The default setting is on and we recommend leaving Phase Control switched on for all sound sources.

STATUS	SIGNAL SEL	SBch	STEREO
MULTI OPE	THX	STANDARD	ADV. SURR

SHIFT PHASE MCACC S.DIRECT

•Press PHASE (PHASE CONTROL) to switch on phase correction.

The PHASE CONTROL indicator on the front panel lights.

Note

1Make sure that the TV’s video input is set to this receiver. (For example, if you connected this receiver to the VIDEO 1 jacks on your TV, make sure that the VIDEO 1 input is now selected.)

2If you need to manually switch the input signal type press SIGNAL SEL (page 28).

3• You may need to check the digital audio output settings on your DVD player or digital satellite receiver. It should be set to output Dolby Digital, DTS and 88.2/96kHz PCM (2 channel) audio, and if there is an MPEG audio option, set this to convert the MPEG audio to PCM.

•Depending on your DVD player or source discs, you may only get digital 2 channel stereo and analog sound. In this case, the receiver must be set to a multichannel listening mode (see Listening in surround sound on page 26 if you need to do this) if you want multichannel surround sound.

4Phase matching is a very important factor in achieving proper sound reproduction. If two waveforms are 'in phase', they crest and trough together, re- sulting in increased amplitude, clarity and presence of the sound signal. If a crest of a wave meets a trough (as shown in the upper section of the diagram above) then the sound will be 'out of phase' and an unreliable sound image will be produced.

9

En