Pioneer SX-X360, S-X360 manual Important the Moulded Plug

Page 3
D3-4-2-1-7b_A_En
K058_En

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT: THE MOULDED PLUG

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark

or the BSI mark

on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.

If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code: Blue : Neutral Brown : Live

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows ;

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.

D3-4-2-1-2-2_B_En

If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling.

Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health.

VENTILATION CAUTION

When installing this unit, make sure to leave space around the unit for ventilation to improve heat radiation (at least 5 cm at top, 5 cm at rear, and 5 cm at each side).

WARNING

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product, and to protect it from overheating. To prevent fire hazard, the openings should never be blocked or covered with items (such as newspapers, table-cloths, curtains) or by operating the equipment on thick carpet or a bed.

 

5 cm

5 cm

5 cm

Receiver subwoofer

Image 3
Contents HTP-GS1 Risk of Electric Shock Do not Open Operating EnvironmentImportant the Moulded Plug Speakers S-X360 box What’s in the boxContents Home theater sound setup Speaker Setup GuideSpeaker Setup Guide Chapter Safety precautions when setting upFront surround setup Speaker Setup GuideBracket screw supplied Mm 10 mm Additional notes on speaker placementAttaching the brackets Mm to 7 mm Before mountingEnglish Receiver subwoofer Connecting upConnecting up Chapter Basic connectionsConnecting up Center Green Receiver subwooferTo AC outlet Listening positionConnecting up Using this system for TV audio Display Controls and displaysControls and displays Chapter Display unitControls and displays Remote control Putting the batteries in the remote control Controls and displays Using the remote controlGetting started Chapter System demo settingUsing the Auto Mcacc setup for optimal surround sound Getting startedPress Mcacc Getting startedListening to your system Chapter Auto listening modeDolby Pro Logic II Music settings Listening to your systemListening in stereo Listening to your system Using Front SurroundUsing Advanced Surround ExtpowerEnhancing dialogue Listening to your system Using the Sound RetrieverUsing Quiet and Midnight listening modes Adjusting the bass and trebleBassmode then press Enter Listening to your system Boosting the bass levelListening to the radio Listening to the radio ChapterListening to the radio You can search for a program type listed above Listening to the radio Using RDSSearching for RDS programs Displaying RDS informationSurround sound settings Surround sound settings ChapterUsing the Setup menu Surround sound settings Adjusting the channel levels using the test toneDual mono setting Other connections Chapter Connecting auxiliary componentsConnecting external antennas Other connectionsDisplay SR+ Setup for Pioneer plasma displaysAutomatic plasma display volume muting Other connectionsUsing the SR+ mode with a Pioneer plasma display Automatic plasma display input switchingAbout the control out jack Additional information Setting up the remote to control your Additional informationGlossary Input Using the TV remote control buttonsPreset code list TV VolumeGeneral Additional information TroubleshootingTuner Error MessagesX360 Speaker system Additional information SpecificationsPioneer Electronics DE Mexico S.A. DE C.V Pioneer Electronics USA INCPioneer Electronics of CANADA, INC Pioneer Europe NV