Pioneer S-X360, SX-X360 manual Additional information Troubleshooting, General

Page 32

09Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

¥If the system does not operate normally due to external effects such as static electricity disconnect the plug from the outlet and insert again to return to normal operating conditions.

¥For audio-related problems, please also check the settings of the audio playback device. See the operating instructions for the device for detailed information.

¥If you cannot use the Dolby Pro Logic II or Sound Retriever functions when listening to a stereo source (such as an audio CD or MP3 tracks) on the Xbox 360, make sure that the digital output setting of the Xbox 360 is set to Stereo.

General

Problem

Remedy

The power does not turn on,

¥ Leave the unit plugged in, wait for one minute, then switch back on.

or switches off suddenly (an

¥ Make sure there are no loose strands of wire touching the unit. This could cause the system

error message may be

to shut off automatically.

displayed at startup).

¥ Check that the speakers are connected correctly.

 

¥ Make sure there is enough space for ventilation around the receiver subwoofer.

 

¥ Make sure the voltage of the mains power source is correct for the model.

 

¥ Try reducing the volume level.

 

¥ If the problem persists, take it to your nearest Pioneer authorized service center or your

 

dealer for servicing.

 

 

No sound is output when

¥ Make sure the component is connected correctly (see Connecting auxiliary components on

an input function is

page 26).

selected.

¥ Turn up the volume.

No sound from surround or center speakers.

¥Refer to Channel level setting on page 24 to check the speaker levels.

¥Check that you havenÕt selected the AUTO, STEREO, or VIRTUAL mode (see Listening in surround sound on page 18).

¥Connect the speakers properly (refer to Connecting up).

CanÕt operate using the

¥ Replace the batteries (Putting the batteries in the remote control on page 15).

remote control.

¥ Operate within 7 m, 30¡ of the remote sensor (Using the remote control on page 15).

 

¥ Remove any obstacles or operate from another position.

 

¥ Avoid exposing the remote sensor on the front panel to direct light.

 

¥ For operating the DVD recorder or other Pioneer component connected to the CONTROL

 

OUT jack of this receiver subwoofer, make sure that the control cable and coaxial cable or at

 

least one set of analog audio cables are connected. (page 28)

 

¥ If the receiver subwoofer is connected to a Pioneer plasma display with an SR+ cable, check

 

that the plasma display is switched on. Point the remote control at the plasma display in order

 

to operate the receiver subwoofer.

 

¥ Check that nothing is mistakenly plugged into the CONTROL IN jack.

 

 

32

En

Page 31 Page 33
Image 32
Page 31 Page 33
Contents HTP-GS1 Operating Environment Risk of Electric Shock Do not OpenImportant the Moulded Plug What’s in the box Speakers S-X360 boxContents Speaker Setup Guide Speaker Setup Guide ChapterSafety precautions when setting up Home theater sound setupSpeaker Setup Guide Front surround setupAdditional notes on speaker placement Attaching the bracketsMm to 7 mm Before mounting Bracket screw supplied Mm 10 mmConnecting up Connecting up ChapterBasic connections English Receiver subwooferConnecting up Receiver subwoofer To AC outletListening position Center GreenConnecting up Using this system for TV audio Controls and displays Controls and displays ChapterDisplay unit DisplayControls and displays Remote control Controls and displays Using the remote control Putting the batteries in the remote controlSystem demo setting Using the Auto Mcacc setup for optimal surround soundGetting started Getting started ChapterGetting started Press McaccAuto listening mode Dolby Pro Logic II Music settingsListening to your system Listening to your system ChapterListening to your system Using Front Surround Using Advanced SurroundExtpower Listening in stereoListening to your system Using the Sound Retriever Using Quiet and Midnight listening modesAdjusting the bass and treble Enhancing dialogueListening to your system Boosting the bass level Bassmode then press EnterListening to the radio Listening to the radioListening to the radio Chapter Listening to the radio Using RDS Searching for RDS programsDisplaying RDS information You can search for a program type listed aboveUsing the Setup menu Surround sound settingsSurround sound settings Chapter Dual mono setting Surround sound settingsAdjusting the channel levels using the test tone Connecting auxiliary components Connecting external antennasOther connections Other connections ChapterSR+ Setup for Pioneer plasma displays Automatic plasma display volume mutingOther connections DisplayAbout the control out jack Using the SR+ mode with a Pioneer plasma displayAutomatic plasma display input switching Additional information Glossary Setting up the remote to control yourAdditional information Using the TV remote control buttons Preset code listTV Volume InputAdditional information Troubleshooting GeneralError Messages TunerAdditional information Specifications X360 Speaker systemPioneer Electronics USA INC Pioneer Electronics of CANADA, INCPioneer Europe NV Pioneer Electronics DE Mexico S.A. DE C.V
Top Page Image Contents