Pioneer VSX-LX52 Select ‘Channel Level’ from the Manual SP Setup menu, Select a setup option

11The system and the other setup

•SB – Select the number of surround back speakers you have (one, two or none).1 Select LARGEx2 or LARGEx1 if your surround back speakers reproduce bass frequencies effectively. Select SMALLx2 or SMALLx1 to send bass frequencies to the other speakers or subwoofer. If you didn’t connect surround back speakers choose NO.

•SW – LFE signals and bass frequencies of channels set to SMALL are output from the subwoofer when YES is selected. Choose the PLUS setting if you want the subwoofer to output bass sound continuously or you want deeper bass (the bass frequencies that

would normally come out the front and center

speakers are also routed to the subwoofer).2 If you did not connect a subwoofer choose NO (the bass frequencies are output from other speakers).

3Select ‘X. OVER’ and set the crossover frequency.3 Frequencies below this point will be sent to the subwoofer (or LARGE speakers).

4When you’re finished, press RETURN.

You will return to the Manual SP Setup menu.

Channel Level

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor when setting up a home theater system.

1Select ‘Channel Level’ from the Manual SP Setup menu.

4a.Manual SP Setup			4a3.Channel Level
A/V RECEIVER			A/V RECEIVER
1. Surr Back System		MCACC :	M1.MEMORY 1
2. Speaker Setting		Test Tone	:	AUTO
3. Channel Level
4. Speaker Distance
5. X-Curve
6. THX Audio Setting
Exit	Return	Exit		Return

2Select a setup option.

•MANUAL – Move the test tone manually from

speaker to speaker and adjust individual channel levels.

•AUTO – Adjust channel levels as the test tone moves from speaker to speaker automatically.

3Confirm your selected setup option.

The test tones will start after you press ENTER.

	4a3.Channel Level
	A/V RECEIVER
	CAUTION
	Loud test tones will be output.
	Please wait...**
Exit	Cancel

4 Adjust the level of each channel using /.

If you selected MANUAL, use / to switch speakers. The AUTO setup will output test tones in the order shown on-screen:

		4a3.Channel Level
		A/V RECEIVER
MCACC : M1.MEMORY 1
L	:	0.00 dB
C	:	0.00 dB
R	:	0.00 dB
SR	:	0.00 dB
SBR	:	0.00 dB
SBL	:	0.00 dB
SL	:	0.00 dB
SW	:	0.00 dB
Exit		Finish

Adjust the level of each speaker as the test tone is emitted.4

5When you’re finished, press RETURN. You will return to the Manual SP Setup menu.

Tip

•You can change the channel levels at any time by

press RECEIVER , then press CH LEVEL, and then using / on the remote control.

Note

1• If you selected Speaker B, ZONE 2 or Front Bi-Amp(in Surround back speaker setting on page 85) you can’t adjust the surround back settings.

•If the surround speakers are set to NO, the surround back speakers will automatically be set to NO.

•If you select one surround back speaker only, make sure that speaker is hooked up to the left surround back terminal.

2If you have a subwoofer and like lots of bass, it may seem logical to select LARGE for your front speakers and PLUS for the subwoofer. This may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in the amount of bass due low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good results, listen to the bass response with it set to PLUS and YES or the front speakers set to LARGE and SMALL alternatively and let your ears judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting SMALL for the front speakers.

3• This setting decides the cutoff between bass sounds playing back from the speakers selected as LARGE, or the subwoofer, and bass sounds playing back from those selected as SMALL. It also decides where the cutoff will be for bass sounds in the LFE channel.

•If you’re using a THX speaker setup, confirm that the crossover frequency is set to 80Hz.

4• If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker to 75 dB SPL (C-weighting/slow reading).

•The subwoofer test tone is output at low volumes. You may need to adjust the level after testing with an actual soundtrack.

86

En