Pioneer VSX-LX60 operating instructions Placing the speakers, Bare wire connections

Page 20

03Connecting your equipment

Bare wire connections

Make sure that the speaker cable you’re going to use is properly prepared with about 10 mm of insulator stripped from each wire, and the exposed wire strands twisted together (fig. A).

To connect a terminal, unscrew the terminal a few turns until there is enough space to insert the exposed wire (fig. B). Once the wire is in position, tighten the terminal until the wire is firmly clamped (fig. C).

fig. A

fig. B

fig. C

10 mm

Important

Please refer to the manual that came with your speakers for details on how to connect the other end of the speaker cables to your speakers.

Other connections on page 53 provides greater detail on alternate speaker setups, such as using speaker system B (page 56), bi-amping (page 57) and bi- wiring (page 57).

If you are using a THX certified subwoofer use the THX INPUT jack on the subwoofer (if your subwoofer has one) or switch the filter position to THX on your subwoofer.

Placing the speakers

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.

The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.

For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from the TV.

When placing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference, such as discoloration of the picture when the TV is switched on. If you do not have magnetically shielded speakers and notice discoloration of the TV picture, move the speakers farther away from the TV.

If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower angle.

Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.

It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.

Surround and surround back speakers should be positioned 60 cm to 90 cm higher than your ears and titled slight downward. Make sure the speakers don’t face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.

Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

Front

Center

Front

left

right

 

 

Subwoofer

Surround

 

Surround

left

 

right

Listening position

Surround back left

 

Surround back right

Single surround back speaker

Caution

Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.

20

En

Image 20
Contents Operating Instructions Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Other Settings Using other functionsOther connections Hdmi ControlInstalling the receiver Before you startBefore you start Chapter Checking what’s in the boxMinute guide Minute guide ChapterIntroduction to home theater Listening to Surround SoundSpeaker configuration in the OSD Switch on the receiver and your TVProgress report is displayed on-screen while Receiver outputs test tones to determine the speakersPlaying a source Problems when using the Auto Mcacc SetupMinute guide Using Phase Control Press Phase Phase Control to select Phase ControlPhase Control indicator on the front panel lights 02 5 minute guideUsing Full Band Phase Control Press Phase Phase Control to selectFullband PHASE.3 Tweeter Midrange WooferRear panel Connecting your equipmentConnecting your equipment Chapter Connecting your equipment When making cable connectionsAudio/video source inputs/outputs Multichannel analog audio inputsConnecting your equipment Connecting your TV and DVD player Connect using a standard video cable or an S-video cableConnecting a satellite/cable receiver or other set-top box VSX-LX70Connecting a DVD/HDD recorder, VCR For a second recorder, use the DVR/VCR2 in inputsUse an optical cable for the connection Connecting digital audio sourcesUse a three-way component video cable Connecting your equipment Connecting analog audio sources TV game, video camera, etcCenter Connecting your equipment Installing your speaker systemConnecting the speakers Bare wire connections Placing the speakersConnecting antennas THX speaker system setupAM loop antenna Assemble the stand as shown in the illustration.1FM wire antenna Connecting external antennasPlugging in the receiver AC outletControls and displays Controls and displays ChapterFront panel Input Selector dial Use to select an input sourceOperating range of remote control unit Controls and displaysControls and displays Display Remote control RECEIVERInput Select SelectStatus Multi OPEShift SOURCEListening to your system Listening to your system ChapterAuto playback Listening in surround soundUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemUsing Front Stage Surround Advance Using Stream DirectListening in stereo TipListening to your system Selecting Mcacc presets Choosing the input signalUsing surround back channel processing Hdmi Digital AnalogUsing the Virtual Surround Back mode BD Tvctrl Using the USB interface USB playbackUSB playback Chapter Basic playback controlsUSB playback Compressed audio compatibilityUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets An introduction to RDSUsing EON Searching for RDS programsDisplaying RDS information Search shows in the displaySystem Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Select the setting you want to adjustFront Align System Setup menuPoint If necessary, confirm the speaker configuration in the OSD.1 Surround back speaker setting Manual Mcacc setupSelect ‘Surr Back System’ from the System Setup menu Select the surround back speaker settingSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuAdjust the level of the left channel When you’re finished, press ReturnSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Select ‘Standing Wave’ from the Manual Mcacc setup menuFine Speaker Distance Standing WaveAcoustic Calibration EQ Adjust How to use Acoustic Calibration EQ ProfessionalHow to interpret the graphical output Acoustic Calibration EQ ProfessionalSelect an option and press Enter Using Acoustic Calibration EQ ProfessionalSelect ‘EQ Professional’ then press Enter Full Band Phase Control Checking Mcacc preset data Select ‘FULL Band Phase CTRL’ from the System Setup menuSelect ‘Data Management’ from the System Setup menu Data ManagementClearing Mcacc presets Copying Mcacc preset dataRenaming Mcacc presets System Setup menu Manual speaker setup Speaker SettingSelect ‘Manual SP Setup’ then press Enter Select ‘Speaker Setting’ from the Manual SP Setup menuChannel Level Speaker DistanceTHX Audio Setting CurveConnecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterConnecting using Hdmi Watching photos and video contentOther connections Basic playback controlsAbout Hdmi Switching the speaker system Selecting the multichannel analog inputsUse the Input Select button to select Multi CH Select ‘Speaker B’ from the ‘Surr Back System’ menuConnect your speakers as shown below Bi-wiring your speakersBi-amping your front speakers Making MULTI-ZONE connections LargeBasic MULTI-ZONE setup Zone Secondary MULTI-ZONE setup ZoneMULTI-ZONE listening options Sub Zone Input sources availableConnecting an IR receiver Using the MULTI-ZONE controlsMULTI-ZONE remote controls RCV/Z3 ZONE3Closet or shelving unit Non-Pioneer IRcomponent Using this receiver with a Pioneer plasma displaySwitching components on and off using the 12 volt trigger Using the SR+ mode with a Pioneer plasma display Pioneer plasmaDisplay Satellite receiver, etcOther connections Connecting a PC for Advanced Mcacc output Advanced Mcacc output using your PCSelect ‘Output PC’ and press Enter Personal computerMaking the Hdmi Control connections Hdmi ControlHdmi Control Chapter Hdmi Control Setting the Hdmi options Synchronized amp modeBefore using synchronization About Hdmi ControlInput Setup menu Other SettingsOther Settings Chapter Video Other Setup menuInput Input Terminals Source Digital Other Settings Multi Channel Input SetupZone Audio Setup SR+ Setup for Pioneer plasma displaysOSD Adjustment Select the ‘PDP Volume Control’ setting you wantSelect ‘OSD Adjustment’ from the Other Setup menu You will return to the Other Setup menuUsing other functions Using other functions ChapterSetting the Audio options Setting What it does OptionsUsing other functions Setting the Video optionsPlaying a different source when recording Making an audio or a video recordingSelect the source you want to record Prepare the source you want to recordReducing the level of an analog signal Switching the speaker impedanceUsing the sleep timer Dimming the displayChecking your system settings Resetting the systemDefault system settings Setting DefaultNeo6 Options Center Image All Inputs Listening Mode 2 ch Listening Mode x chListening Mode HP Channel level M1-M6 Speaker Distance M1-M6Setting the remote to control other components Selecting preset codes directlyRemote controls Controlling the rest of your systemErasing one of the remote control button settings Resetting the remote control presetsConfirming preset codes Controlling the rest of your systemRenaming input source names Multi Operation and System OffDirect function Programming a multi-operation or a shutdown sequenceControls for TVs Using multi operationsUsing System off Function Components Controls for other componentsButtons Function Components Decide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorButton s Function Components Troubleshooting PowerSymptom Remedy Additional informationAdditional information No soundOther audio problems Phase Control featureSettings VideoProfessional Calibration EQ graphical output DisplayGraphical output following Calibration does not appearRemote control Hdcp Error shows in the displaySymptomRemedy Symptom Cause ActionUSB interface VSX-LX60 only IPod messagesAdditional information Surround sound formats DolbyAbout THX Windows Media Audio 9 ProfessionalAbout Neural Surround Auto Surround Stereo 2 channel signal formatsInput signal format Standard Multichannel signal formats DTS-ES b DTS-ES Matrix/Discrete DTS-ES+THX Matrix/Discrete Movie a MOVIE+THX aWMA9 Pro Channel DecodingSurround Back speakers Input signal format Sacd Direct VSX-LX70 or Straight decoding VSX-LX60Additional information Specifications Our philosophy Additional information Cleaning the unitFeatures DCDi IPod ReadyPioneer Corporation