Pioneer VSX-LX60 operating instructions Remote control, Hdcp Error shows in the display

Page 87

Additional information

14

Remote control

Symptom

Remedy

Cannot be remote controlled.

• Try replacing the batteries in the remote control (see Loading the batteries on page 6).

 

• Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see Operating range

 

of remote control unit on page 24).

 

• Check that there are no obstacles between the receiver and the remote control.

 

• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.

 

• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this unit’s

 

sensor on page 81).

 

 

Other components can’t be

• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.

operated with the system remote.

• The preset code may be incorrect. Redo the procedure for entering preset codes.

 

 

The SR cable is connected, but

• Reinsert the SR cable, making sure it’s connected to the right jack (see Using this receiver with a Pioneer

the connected components can’t

plasma display on page 61).

be operated with the remote.

• Make sure that there is an analog or HDMI connection between the units. This is necessary for the SR

 

feature to work.

 

• Check that the other component is made by Pioneer. The SR feature only works with Pioneer equipment.

 

 

HDMI

Symptom

Remedy

The HDMI indicator blinks

• Check all the points below.

continuously.

 

 

 

No picture or sound.

• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-

 

compatible. If they are not, please connect them using the component, S-video or composite video jacks.

 

• Depending on the connected source component, it’s possible that it will not work with this receiver (even

 

if it is HDCP-compatible). In this case, connect using the component, S-video or composite video jacks

 

between source and receiver.

 

• If the problem still persists when connecting your HDMI component directly to your monitor, please

 

consult the component or monitor manual or contact the manufacturer for support.

 

• If video images do not appear on your TV or plasma display, try adjusting the resolution, DeepColor or

 

other setting for your component.

 

• If ‘NOT SUPPORT’ appears in the receiver’s display, try adjusting the resolution, DeepColor or other

 

setting for your component.

 

• While analog video signals are being output over HDMI, use a separate connection for audio output.

 

• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to THROUGH, you

 

cannot hear audio output from all channels. In this case, make a digital or analog audio connection.

 

• To output signals in DeepColor, use an HDMI cable (compliant with Version 1.3a, Category 2) to connect

 

this receiver to a component or TV with the DeepColor feature.

 

 

No picture.

• Try changing the Resolution setting (in Setting the Video options on page 71).

 

 

No sound, or sound suddenly

• Check that the HDMI AV setting is set to AMP/THROUGH.

ceases.

• If the component is a DVI device, use a separate connection for the audio.

 

• If analog video is being output over HDMI, please use a separate connection for the audio.

 

• Check the audio output settings of the source component.

 

 

Noisy or distorted picture.

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video

 

quality may just be poor (with some video game units, for example). The picture quality may also depend on

 

the settings, etc. of your display device. Switch off the video converter and reconnect the source and display

 

device using the same type of connection (component, S-video or composite), then start playback again.

 

• If the problem still persists when connecting your HDMI component directly to your monitor, please

 

consult the component or monitor manual or contact the manufacturer for support.

HDCP ERROR shows in the display.

•Check whether or not the connected component is compatible with HDCP. If it is not compatible with HDCP, reconnect the source device using a different type of connection (component, S-video or composite). Some components that are compatible with HDCP still cause this message to be displayed, but so long as there is no problem with displaying video, this is not a malfunction.

87

En

Page 86 Page 88
Image 87
Page 86 Page 88
Contents Operating Instructions Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Contents Hdmi Control Other SettingsUsing other functions Other connectionsChecking what’s in the box Installing the receiverBefore you start Before you start ChapterListening to Surround Sound Minute guideMinute guide Chapter Introduction to home theaterReceiver outputs test tones to determine the speakers Speaker configuration in the OSDSwitch on the receiver and your TV Progress report is displayed on-screen whileProblems when using the Auto Mcacc Setup Minute guidePlaying a source 02 5 minute guide Using Phase ControlPress Phase Phase Control to select Phase Control Phase Control indicator on the front panel lightsTweeter Midrange Woofer Using Full Band Phase ControlPress Phase Phase Control to select Fullband PHASE.3Connecting your equipment Connecting your equipment ChapterRear panel Multichannel analog audio inputs Connecting your equipmentWhen making cable connections Audio/video source inputs/outputsConnect using a standard video cable or an S-video cable Connecting your equipment Connecting your TV and DVD playerVSX-LX70 Connecting a satellite/cable receiver or other set-top boxFor a second recorder, use the DVR/VCR2 in inputs Connecting a DVD/HDD recorder, VCRConnecting digital audio sources Use a three-way component video cableUse an optical cable for the connection TV game, video camera, etc Connecting your equipment Connecting analog audio sourcesConnecting your equipment Installing your speaker system Connecting the speakersCenter Placing the speakers Bare wire connectionsAssemble the stand as shown in the illustration.1 Connecting antennasTHX speaker system setup AM loop antennaAC outlet FM wire antennaConnecting external antennas Plugging in the receiverInput Selector dial Use to select an input source Controls and displaysControls and displays Chapter Front panelControls and displays Operating range of remote control unitControls and displays Display Select Remote controlRECEIVER Input SelectSOURCE StatusMulti OPE ShiftListening in surround sound Listening to your systemListening to your system Chapter Auto playbackListening to your system Using the Home THX modesUsing the Advanced surround effects THX Games ModeTip Using Front Stage Surround AdvanceUsing Stream Direct Listening in stereoHdmi Digital Analog Listening to your system Selecting Mcacc presetsChoosing the input signal Using surround back channel processingUsing the Virtual Surround Back mode BD Tvctrl Basic playback controls Using the USB interfaceUSB playback USB playback ChapterCompressed audio compatibility USB playbackListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAn introduction to RDS Using the tunerNaming station presets Listening to station presetsSearch shows in the display Using EONSearching for RDS programs Displaying RDS informationSelect the setting you want to adjust System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSystem Setup menu PointFront Align If necessary, confirm the speaker configuration in the OSD.1 Select the surround back speaker setting Surround back speaker settingManual Mcacc setup Select ‘Surr Back System’ from the System Setup menuWhen you’re finished, press Return Select ‘Manual MCACC’ from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu Adjust the level of the left channelStanding Wave Select ‘Fine SP Distance’ from the Manual Mcacc setup menuSelect ‘Standing Wave’ from the Manual Mcacc setup menu Fine Speaker DistanceAcoustic Calibration EQ Professional Acoustic Calibration EQ AdjustHow to use Acoustic Calibration EQ Professional How to interpret the graphical outputUsing Acoustic Calibration EQ Professional Select ‘EQ Professional’ then press EnterSelect an option and press Enter Full Band Phase Control Data Management Checking Mcacc preset dataSelect ‘FULL Band Phase CTRL’ from the System Setup menu Select ‘Data Management’ from the System Setup menuCopying Mcacc preset data Renaming Mcacc presetsClearing Mcacc presets Select ‘Speaker Setting’ from the Manual SP Setup menu System Setup menu Manual speaker setupSpeaker Setting Select ‘Manual SP Setup’ then press EnterSpeaker Distance Channel LevelCurve THX Audio SettingOther connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connectionsBasic playback controls Connecting using HdmiWatching photos and video content Other connectionsAbout Hdmi Select ‘Speaker B’ from the ‘Surr Back System’ menu Switching the speaker systemSelecting the multichannel analog inputs Use the Input Select button to select Multi CHBi-wiring your speakers Bi-amping your front speakersConnect your speakers as shown below Large Making MULTI-ZONE connectionsSub Zone Input sources available Basic MULTI-ZONE setup ZoneSecondary MULTI-ZONE setup Zone MULTI-ZONE listening optionsRCV/Z3 ZONE3 Connecting an IR receiverUsing the MULTI-ZONE controls MULTI-ZONE remote controlsUsing this receiver with a Pioneer plasma display Switching components on and off using the 12 volt triggerCloset or shelving unit Non-Pioneer IRcomponent Satellite receiver, etc Using the SR+ mode with a Pioneer plasma displayPioneer plasma DisplayPersonal computer Other connections Connecting a PC for Advanced Mcacc outputAdvanced Mcacc output using your PC Select ‘Output PC’ and press EnterHdmi Control Hdmi Control ChapterMaking the Hdmi Control connections About Hdmi Control Hdmi Control Setting the Hdmi optionsSynchronized amp mode Before using synchronizationOther Settings Other Settings ChapterInput Setup menu Other Setup menu Input Input Terminals Source DigitalVideo SR+ Setup for Pioneer plasma displays Other SettingsMulti Channel Input Setup Zone Audio SetupYou will return to the Other Setup menu OSD AdjustmentSelect the ‘PDP Volume Control’ setting you want Select ‘OSD Adjustment’ from the Other Setup menuSetting What it does Options Using other functionsUsing other functions Chapter Setting the Audio optionsSetting the Video options Using other functionsPrepare the source you want to record Playing a different source when recordingMaking an audio or a video recording Select the source you want to recordDimming the display Reducing the level of an analog signalSwitching the speaker impedance Using the sleep timerSetting Default Checking your system settingsResetting the system Default system settingsChannel level M1-M6 Speaker Distance M1-M6 Neo6 Options Center Image All Inputs Listening Mode 2 chListening Mode x ch Listening Mode HPControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct functionUsing multi operations Using System offControls for TVs Controls for other components Buttons Function ComponentsFunction Components Operating other Pioneer components with this unit’s sensor Button s Function ComponentsDecide which component you want to use the remote sensor Additional information TroubleshootingPower Symptom RemedyNo sound Additional informationPhase Control feature Other audio problemsVideo SettingsCalibration does not appear Professional Calibration EQ graphical outputDisplay Graphical output followingHdcp Error shows in the display Remote controlIPod messages SymptomRemedySymptom Cause Action USB interface VSX-LX60 onlyDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THXAbout Neural Surround Stereo 2 channel signal formats Input signal format StandardAuto Surround Multichannel signal formats Decoding DTS-ES b DTS-ES Matrix/Discrete DTS-ES+THX Matrix/DiscreteMovie a MOVIE+THX a WMA9 Pro ChannelSacd Direct VSX-LX70 or Straight decoding VSX-LX60 Surround Back speakers Input signal formatAdditional information Specifications Additional information Cleaning the unit FeaturesOur philosophy IPod Ready DCDiPioneer Corporation
Top Page Image Contents