Pioneer VSX-2016AV Using other functions, Dimming the display, Switching the speaker impedance

Page 59

Using other functions

•Press RECEIVER then press SLEEP repeatedly to set the sleep time.

 

30 min

 

60 min

 

 

 

 

Off

 

 

90 min

 

 

 

 

•You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again.1

Dimming the display

You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds.

CD-R/TAPE HDMI2 USB

iPod HDMI1 TUNER RECEIVER

SLEEP

VIDEO

ANALOG

 

SEL

ATT

SR+

DIMMER

MIDNIGHT/

 

 

LOUDNESS

DIALOG E

S.RETRIEVER

 

D ACCESS

•Press RECEIVER then press DIMMER repeatedly to change the brightness of the front panel display.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 Ω impedance rating. Use the front panel controls to do this.

• With the receiver in standby, press STANDBY/ ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6 Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8 Ω or more.

11

1Press STATUS to check the system settings. These appear on both the OSD and the front panel display.2

STATUS

DOLBY DIGITAL 3/2.1

PCM 96+DOLBY PLII MS

Signal Select : AUTO

SBch Processing: OFF

Retriever : ON

Video Select : OFF

MCACC Position : M1

The front panel display shows each of the following settings for two seconds each:

Input source

Listening mode

 

 

Signal select

Surround Back Processing

 

 

Sound Retriever

Video Select

 

 

MCACC Position

 

 

 

2When you’re finished, press STATUS again to switch off the display.

Resetting the system

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the front panel TONE button,

press and hold STANDBY/ON for about three seconds.

The display shows RESET?.

3Press the front panel ENTER button. The display shows RESET OK?.

4Press SYSTEM SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

•Note that all settings will be saved, even if the receiver is unplugged.

Checking your system settings

Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset.

AUDIO SUBTITLE HDD

DISPCH

DVD

CH

STATUS

SIGNAL SEL

SBch

STEREO

MULTI OPE

THX

STANDARD

ADV.SURR

SHIFT PHASE MCACC S.DIRECT

Note

1You can also switch off the sleep timer simply by switching off the receiver.

2If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on.

59

En

Page 58 Page 60
Image 59
Page 58 Page 60
Contents
VSX-2016AV-S Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Before you start Installing the receiverIntroduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterWait for the test tones to finish then confirm Speaker configuration in the OSDMinute guide Playing a source Better sound using Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideRear panel Connecting your equipmentConnecting your equipment Chapter About the video converter Connecting your equipmentWhen making cable connections DVD player Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box 342DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionUse a three-way component video cable Connecting digital audio sourcesTape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsTHX speaker system setup Connecting antennasPlugging in the receiver Connecting external antennasPlug the power cord into a power outlet Front panel Controls and displaysControls and displays Chapter Controls and displays Operating range of remote control unitSleep Over / ATTVideo Conv Stream DirectInput Select Controls and displays Remote controlReceiver Shift 6TUNE/ST /ENTERStatus Multi OPEStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects THX Games ModeWhile listening to a source, press Mcacc Selecting Mcacc presetsUsing Stream Direct Listening in stereoUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsBasic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout WMA USB playbackOther compatibility information About MPEG-4 AACListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAn introduction to RDS Using the tunerNaming station presets Listening to station presetsPress Disp for RDS information Using EONDisplaying RDS information Select the setting you want to adjust System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuMemory System Setup menuMake sure ‘OK’ is selected, then press Enter Surround back speaker settingFine Channel Level Manual Mcacc setupFine Speaker Distance Adjust the level of the left channelWhen youre finished, press Return Select ‘Fine SP Distance’ from the Manual Mcacc setup menuProfessional Acoustic Calibration EQ How to use Professional Acoustic Calibration EQAcoustic Calibration EQ Select an option and press Enter How to interpret the graphical outputUsing Professional Acoustic Calibration EQ Select ‘EQ Professional’ then press EnterEQ OFF Data ManagementRenaming Mcacc presets Checking Mcacc preset dataCopying Mcacc preset data Clearing Mcacc presets Manual speaker setupSpeaker Setting Channel Level Select a setup optionConfirm your selected setup option Adjust the level of each channel using the buttonsCurve Speaker DistanceBass Peak Level Select ‘Return’ then press Enter to finish THX Audio SettingChoose the X-Curve setting you want Select ‘THX Audio Setting’ from the Manual SP Setup menuOther connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connectionsUse To move to previous/next levels Connecting using HdmiOther connections Basic playback controlsSelecting the multichannel analog inputs Connecting the multichannel analog inputsSecond Zone speaker B setup About HdmiConnect your speakers as shown below Switching the speaker system2nd Zone setting only.1 Bi-amping your front speakersLarge Other connections Bi-wiring your speakersConnecting additional amplifiers Using this receiver with a Pioneer plasma displayDVD player Satellite receiver, etc Using the SR+ mode with a Pioneer plasma displayPioneer plasma Display Input function default and possible settings Other Settings Other Settings Chapter Input Setup menuOSD Adjustment Other SettingsOther Setup menu SR+ Setup for Pioneer plasma displaysSetting What it does Options Using other functionsUsing other functions Chapter Setting the AV optionsWatching video and audio sources independently Using other functions Making an audio or a video recordingReducing the level of an analog signal Using the sleep timerChecking your system settings Using other functionsSwitching the speaker impedance Resetting the systemInputs Default system settingsSetting Default Controlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct functionFrom the menu and press Enter Using multi operationsUsing System off Select the button for the command you want to inputFunction Components Controlling the rest of your system Controls for TVsControls for other components Buttons Function Components+ CH Operating other Pioneer components with this unit’s sensorDecide which component you want to use the remote sensor CH +Additional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsPhase Control feature 96 kHz DisplayUSB interface Remote controlSymptomRemedy IPod messages Symptom Cause ActionError There is a problem with the signal path fromWindows Media Audio 9 Professional Additional information Surround sound formatsDolby About THX Auto Surround Listening modes with different input signal formatsStereo 2 channel signal formats Input signal format StandardMultichannel signal formats Pro Logic II Movie Pro Logic IIx MovieNeo6 Cinema Cleaning the unit Additional information Specifications06C00001 Printed ARB7355-A Pioneer Corporation
Top Page Image Contents