Pioneer VSX-2016AV USB playback Chapter, Using the USB interface, Basic playback controls

Page 31

USB playback

Chapter 6:

USB playback

Using the USB interface

It is possible to listen to two-channel audio1 using the USB interface on the front of this receiver. Connect a

USB mass storage device2 as shown below.

06

Important

If a USB ERR message lights in the display, try following the points below:

Error

What it means

 

 

1 Press USB (SHIFT+TUNER).

USB ERR1

The power requirements of the USB device are too high for this receiver.

2 Connect your USB device.

The USB terminal is located on the front panel.

USB ERR2 The USB device is incompatible

PHONES

S-VIDEO

 

 

VIDEO/GAME INPUT

 

 

USB

MCACC

 

VIDEO

L AUDIO R

DIGITAL IN

 

SETUP MIC

SYSTEMTUNING/ TUNER

SETUP RETURN TONE STATION EDIT SPEAKERS

MULTI JOG

USB ERR3 See USB interface on page 71 for more on this error message.

•

Switch the receiver off, then on again.

• Reconnect the USB device with the receiver switched

 

off.

This receiver

USB mass storage device

3 Press (play) to start playback.

Files/folders play in sequential order based on the filename (according to the Unicode standard). Within a given directory, all files are played before continuing to folders/subfolders.

•Make sure the receiver is in standby when disconnecting the USB device.

Basic playback controls

The following table shows the basic controls on the remote for USB playback.

• Select another input source (like DVD/CD), then

switch back to USB.

• Use a dedicated AC adapter (supplied with the

device) for USB power.

If this doesn’t remedy the problem, it is likely your USB device is incompatible.

Compressed audio compatibility

Note that although most standard bit/sampling rate combinations for compressed audio are compatible, some irregularly encoded files may not play back. The list below shows compatible formats for compressed audio files:

•MP3 (MPEG-1/2/2.5 Audio Layer 3) – Sampling rates: 8 kHz to 48 kHz; Bit rates: 8 kbps to 320 kbps (128 kbps or higher recommended); File extension: .mp3

Button What it does

Starts normal playback.

Pauses/unpauses playback.

Press to start fast reverse scanning (press twice for high-speed scanning).

Press to start fast forward scanning. (press twice for high-speed scanning).

Skips to the start of the current track, then previous tracks.

Skips to the next track.

•WMA (Windows Media Audio) – Sampling rates: 32

kHz / 44.1 kHz; Bit rates: 32 kbps to 192 kbps (128

kbps or higher recommended); File extension: .wma;

WMA9 Pro and WMA lossless encoding: No

•AAC (MPEG-4 Advanced Audio Coding) – Sampling rates: 11.025 kHz to 48 kHz; Bit rates: 16 kbps to 320 kbps (128 kbps or higher recommended); File extension: .m4a; Apple lossless encoding: No

Note

1This includes playback of WMA/MP3/MPEG-4 AAC files (except files with copy-protection or restricted playback).

2• Compatible USB devices include external magnetic hard drives, portable flash memory (particularly keydrives) and digital audio players (MP3 players) of format FAT16/32. It is not possible to connect this unit to a personal computer for USB playback.

•Pioneer cannot guarantee compatibility (operation and/or bus power) with all USB mass storage devices and assumes no responsibility for any loss of data that may occur when connected to this receiver.

•With large amounts of data, it may take longer for the receiver to read the contents of a USB device.

31

En

Page 30 Page 32
Image 31
Page 30 Page 32
Contents
VSX-2016AV-S Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Before you start Installing the receiverIntroduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterMinute guide Speaker configuration in the OSDWait for the test tones to finish then confirm Playing a source Better sound using Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter DVD player Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box 342DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionUse a three-way component video cable Connecting digital audio sourcesTape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsTHX speaker system setup Connecting antennasPlug the power cord into a power outlet Connecting external antennasPlugging in the receiver Controls and displays Chapter Controls and displaysFront panel Controls and displays Operating range of remote control unitSleep Over / ATTVideo Conv Stream DirectReceiver Controls and displays Remote controlInput Select Shift 6TUNE/ST /ENTERStatus Multi OPEStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround sound Listening to your system Using the Home THX modes Using the Advanced surround effects THX Games ModeWhile listening to a source, press Mcacc Selecting Mcacc presetsUsing Stream Direct Listening in stereoUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsBasic playback controls Using the USB interfaceUSB playback USB playback ChapterAbout WMA USB playbackOther compatibility information About MPEG-4 AACListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAn introduction to RDS Using the tunerNaming station presets Listening to station presetsDisplaying RDS information Using EONPress Disp for RDS information Select the setting you want to adjust System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuMemory System Setup menuMake sure ‘OK’ is selected, then press Enter Surround back speaker settingFine Channel Level Manual Mcacc setupFine Speaker Distance Adjust the level of the left channelWhen youre finished, press Return Select ‘Fine SP Distance’ from the Manual Mcacc setup menuAcoustic Calibration EQ How to use Professional Acoustic Calibration EQProfessional Acoustic Calibration EQ Select an option and press Enter How to interpret the graphical outputUsing Professional Acoustic Calibration EQ Select ‘EQ Professional’ then press EnterEQ OFF Data ManagementCopying Mcacc preset data Checking Mcacc preset dataRenaming Mcacc presets Speaker Setting Manual speaker setupClearing Mcacc presets Channel Level Select a setup optionConfirm your selected setup option Adjust the level of each channel using the buttonsBass Peak Level Speaker DistanceCurve Select ‘Return’ then press Enter to finish THX Audio SettingChoose the X-Curve setting you want Select ‘THX Audio Setting’ from the Manual SP Setup menuOther connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connectionsUse To move to previous/next levels Connecting using HdmiOther connections Basic playback controlsSelecting the multichannel analog inputs Connecting the multichannel analog inputsSecond Zone speaker B setup About HdmiConnect your speakers as shown below Switching the speaker system2nd Zone setting only.1 Bi-amping your front speakersLarge Other connections Bi-wiring your speakersConnecting additional amplifiers Using this receiver with a Pioneer plasma displayDVD player Satellite receiver, etc Using the SR+ mode with a Pioneer plasma displayPioneer plasma DisplayInput function default and possible settings Other SettingsOther Settings Chapter Input Setup menuOSD Adjustment Other SettingsOther Setup menu SR+ Setup for Pioneer plasma displaysSetting What it does Options Using other functionsUsing other functions Chapter Setting the AV optionsWatching video and audio sources independently Using other functions Making an audio or a video recordingReducing the level of an analog signal Using the sleep timerChecking your system settings Using other functionsSwitching the speaker impedance Resetting the systemSetting Default Default system settingsInputs Controlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesMulti Operation and System Off Direct functionFrom the menu and press Enter Using multi operationsUsing System off Select the button for the command you want to inputFunction Components Controlling the rest of your system Controls for TVsControls for other components Buttons Function Components+ CH Operating other Pioneer components with this unit’s sensorDecide which component you want to use the remote sensor CH +Additional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsPhase Control feature SettingsVideo 96 kHz DisplaySymptomRemedy Remote controlUSB interface IPod messages Symptom Cause ActionError There is a problem with the signal path fromDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THX Auto Surround Listening modes with different input signal formatsStereo 2 channel signal formats Input signal format StandardMultichannel signal formats Neo6 Cinema Pro Logic IIx MoviePro Logic II Movie Cleaning the unit Additional information Specifications06C00001 Printed ARB7355-A Pioneer Corporation
Top Page Image Contents