Pioneer VSX-2016AV operating instructions Additional information, Other audio problems

Page 68

13Additional information

Symptom

No sound from surround back speakers.

Remedy

•Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on page 45).

•Make sure surround back processing is set to SBch ON (see Using surround back channel processing on page 29).

•If the source is Dolby Surround EX or DTS ES with no flag to indicate 6.1 compatibility, then with surround back processing set to SBch Auto, there will be no sound from the surround back speakers. In this case, set to SBch ON (see Using surround back channel processing on page 29).

•If the source does not have 6.1 playback channels, make sure that surround back processing is set to SBch ON and a surround mode is selected (see Listening in surround sound on page 26).

•Check the speaker connections (see Connecting the speakers on page 17). If only one surround back speaker is connected, make sure it’s connected to the left channel speaker terminal.

No sound from subwoofer.

• Check that the subwoofer is connected properly, switched on and the volume turned up.

 

• If your subwoofer has a sleep function, make sure it is switched off.

 

• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 45).

 

• The crossover frequency may be set too low; try setting it higher to match the characteristics of your other

 

speakers (see Speaker Setting on page 45)

 

• If there is very little low frequency information in the source material, change your speaker settings to

 

Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on page 45).

 

• Check that the LFE channel is not set to –80dB, or a very quiet setting (see Bass Peak Level on page 47).

 

• Check the speaker level settings (see Channel Level on page 46).

No sound from one speaker.

•Check the speaker connection (see Connecting the speakers on page 17).

•Check the speaker level settings (see Channel Level on page 46).

•Check that the speaker hasn’t been set to NO (see Speaker Setting on page 45).

•The channel may not be recorded in the source. By using one of the advanced effect listening mode, you may be able to create the missing channel (see Listening in surround sound on page 26).

Sound is produced from analog

• Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 29).

components, but not from digital

• Make sure that the digital input is assigned correctly for the input jack the component is connected to

ones (DVD, LD, CD-ROM etc.).

(see The Input Setup menu on page 55).

 

• Check the digital output settings on the source component.

 

• If the source component has a digital volume control, make sure this is not turned down.

 

• Make sure that the multichannel analog inputs are not selected. Select any other input source.

 

 

No sound is output or a noise is

• Check that your DVD player is compatible with Dolby Digital/DTS discs.

output when Dolby Digital/DTS

• Check the digital output settings of your DVD player. Make sure that the DTS signal output is set to On.

software is played back.

• If the source component has a digital volume control, make sure this is not turned down.

Other audio problems

Symptom

Remedy

Broadcast stations cannot be

For FM broadcasts

selected automatically, or there is

• Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc.

considerable noise in radio

• Use an outdoor antenna for better reception (see page 20).

broadcasts.

For AM broadcasts

 

• Adjust the position and direction of the AM antenna.

 

• Use an outdoor antenna for better reception (see page 20).

 

• Noise may be caused by interference from other equipment, such as a fluorescent light, motor, etc.

 

Switch off or move the other equipment, or move the AM antenna.

 

 

A multichannel DVD source

• Make sure that the multichannel analog inputs are selected (see Selecting the multichannel analog inputs

appears to be downmixed to 2

on page 51).

channels during playback.

 

Noise is output when scanning a • This is not a malfunction of the receiver. The scan function of your player alters the digital information,

DTS CD.

making it unreadable, resulting in noise being output. Lower the volume when scanning.

 

 

When playing a DTS format LD

• Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 29).

there is audible noise on the

 

soundtrack.

 

 

 

68

En

Page 67 Page 69
Image 68
Page 67 Page 69
Contents VSX-2016AV-S Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Other Settings Using other functionsOther connections Controlling the rest of your systemFeatures Before you startBefore you start Chapter Checking what’s in the boxBefore you start Installing the receiver Loading the batteriesAutomatically setting up for surround sound Mcacc Minute guide02 5 minute guide Chapter Introduction to home theaterWait for the test tones to finish then confirm Speaker configuration in the OSDMinute guide Better sound using Phase Control Problems when using the Auto Mcacc Setup02 5 minute guide Playing a sourceRear panel Connecting your equipmentConnecting your equipment Chapter About the video converter Connecting your equipmentWhen making cable connections Connecting your equipment Connecting your TV and DVD player Connecting a satellite/cable receiver or other set-top box342 DVD playerConnecting a DVD/HDD recorder, VCR and other video sources Using the component video jacksUse an optical cable for the connection DVR, VCR, etcConnecting digital audio sources Use a three-way component video cableConnecting analog audio sources Connecting a component to the front panel inputsAbout the WMA9 Pro decoder Tape deck, etcConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupPlugging in the receiver Connecting external antennasPlug the power cord into a power outlet Front panel Controls and displaysControls and displays Chapter Operating range of remote control unit Controls and displaysOver / ATT Video ConvStream Direct SleepInput Select Controls and displays Remote controlReceiver 6TUNE/ST /ENTER StatusMulti OPE ShiftListening to your system Listening to your system ChapterAuto playback Listening in surround sound Standard surround soundUsing the Home THX modes Using the Advanced surround effectsTHX Games Mode Listening to your systemSelecting Mcacc presets Using Stream DirectListening in stereo While listening to a source, press McaccListening to your system Choosing the input signal Using the Virtual Surround Back modeUsing Midnight and Loudness Using the Sound RetrieverUsing the tone controls Press Tone to select the frequency you want to adjustUsing the USB interface USB playbackUSB playback Chapter Basic playback controlsUSB playback Other compatibility informationAbout MPEG-4 AAC About WMAUsing the tuner Using the tuner ChapterSaving station presets Listening to the radioUsing the tuner Naming station presetsListening to station presets An introduction to RDSPress Disp for RDS information Using EONDisplaying RDS information System Setup menu System Setup menu ChapterMaking receiver settings from the System Setup menu Select the setting you want to adjustSystem Setup menu MemorySurround back speaker setting Make sure ‘OK’ is selected, then press EnterManual Mcacc setup Fine Channel LevelAdjust the level of the left channel When youre finished, press ReturnSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Speaker DistanceProfessional Acoustic Calibration EQ How to use Professional Acoustic Calibration EQAcoustic Calibration EQ How to interpret the graphical output Using Professional Acoustic Calibration EQSelect ‘EQ Professional’ then press Enter Select an option and press EnterData Management EQ OFFRenaming Mcacc presets Checking Mcacc preset dataCopying Mcacc preset data Clearing Mcacc presets Manual speaker setupSpeaker Setting Select a setup option Confirm your selected setup optionAdjust the level of each channel using the buttons Channel LevelCurve Speaker DistanceBass Peak Level THX Audio Setting Choose the X-Curve setting you wantSelect ‘THX Audio Setting’ from the Manual SP Setup menu Select ‘Return’ then press Enter to finishConnecting an iPod Connecting your iPod to the receiverOther connections Other connections ChapterConnecting using Hdmi Other connectionsBasic playback controls Use To move to previous/next levelsConnecting the multichannel analog inputs Second Zone speaker B setupAbout Hdmi Selecting the multichannel analog inputsSwitching the speaker system 2nd Zone setting only.1Bi-amping your front speakers Connect your speakers as shown belowOther connections Bi-wiring your speakers Connecting additional amplifiersUsing this receiver with a Pioneer plasma display LargeUsing the SR+ mode with a Pioneer plasma display Pioneer plasmaDisplay DVD player Satellite receiver, etcOther Settings Other Settings ChapterInput Setup menu Input function default and possible settingsOther Settings Other Setup menuSR+ Setup for Pioneer plasma displays OSD AdjustmentUsing other functions Using other functions ChapterSetting the AV options Setting What it does OptionsUsing other functions Making an audio or a video recording Reducing the level of an analog signalUsing the sleep timer Watching video and audio sources independentlyUsing other functions Switching the speaker impedanceResetting the system Checking your system settingsInputs Default system settingsSetting Default Setting the remote to control other components Selecting preset codes directlyProgramming signals from other remote controls Controlling the rest of your systemErasing one of the remote control button settings Resetting the remote control presetsConfirming preset codes Controlling the rest of your systemRenaming input source names Multi Operation and System OffDirect function Programming a multi-operation or a shutdown sequenceUsing multi operations Using System offSelect the button for the command you want to input From the menu and press EnterControlling the rest of your system Controls for TVs Controls for other componentsButtons Function Components Function ComponentsOperating other Pioneer components with this unit’s sensor Decide which component you want to use the remote sensorCH + + CHTroubleshooting PowerAdditional information Additional information ChapterOther audio problems Additional informationVideo SettingsPhase Control feature Display 96 kHzUSB interface Remote controlSymptomRemedy Symptom Cause Action ErrorThere is a problem with the signal path from IPod messagesWindows Media Audio 9 Professional Additional information Surround sound formatsDolby About THX Listening modes with different input signal formats Stereo 2 channel signal formatsInput signal format Standard Auto SurroundMultichannel signal formats Pro Logic II Movie Pro Logic IIx MovieNeo6 Cinema Additional information Specifications Cleaning the unitPioneer Corporation 06C00001 Printed ARB7355-A

VSX-2016AV specifications

The Pioneer VSX-2016AV is a versatile and feature-rich AV receiver that has garnered attention for its ability to deliver a cinematic experience in the home. With a focus on sound quality and user-friendly features, the VSX-2016AV stands out as a strong option for both casual listeners and serious home theater enthusiasts.

One of the primary attractions of the VSX-2016AV is its robust audio performance. It supports Dolby TrueHD and DTS-HD Master Audio, ensuring that users can enjoy high-resolution soundtracks from their Blu-ray discs. The receiver also features Pioneer's proprietary Sound Retriever technology that enhances compressed audio files, allowing for a more engaging listening experience, regardless of the source.

The VSX-2016AV does not skimp on connectivity options, offering multiple HDMI inputs and outputs to accommodate a range of devices. This includes support for 4K pass-through, making it future-proof for users with advanced video sources. In addition to HDMI, the receiver also provides options for component video, composite video, and analog audio connections, catering to a variety of setups.

Another standout feature is the integrated MCACC (Multi-Channel Acoustic Calibration System) technology. This system automatically calibrates the receiver to the acoustics of the room, ensuring that users experience optimal sound performance based on their specific environment. The result is a well-balanced audio output that enhances the overall listening experience.

With six channels of amplification, the VSX-2016AV is capable of powering a full surround sound system. The receiver provides a total power output of 100 watts per channel, which is ample for most home theater setups. It also includes various sound modes, allowing users to customize the audio output for movies, music, and gaming.

A user-friendly interface and remote control system make it easy to navigate through the various settings and options. The front panel features a clear display that provides vital information about input selection, volume levels, and audio formats. Additionally, Pioneer's iControlAV app enables smartphone control, allowing users to manage their audio settings seamlessly.

In conclusion, the Pioneer VSX-2016AV combines advanced audio technologies with a robust feature set, making it an excellent choice for home entertainment enthusiasts. Its emphasis on sound quality, along with the convenience of connectivity options and user-friendly controls, ensures that it can meet the needs of a diverse range of users. Whether for movie nights or music listening, this AV receiver stands ready to elevate the home audio experience.
Top Page Image Contents