Pioneer VSX-1017AV-K, VSX-1017AV-S manual Placing the speakers, Bare wire connections

Page 19

Connecting your equipment

03

Bare wire connections

Make sure that the speaker cable you’re going to use is properly prepared with about 10 mm of insulator stripped from each wire, and the exposed wire strands twisted together (fig. A).

To connect a terminal, unscrew the terminal a few turns until there is enough space to insert the exposed wire (fig. B). Once the wire is in position, tighten the terminal until the wire is firmly clamped (fig. C).

fig. A

fig. B

fig. C

10 mm

Important

•Please refer to the manual that came with your speakers for details on how to connect the other end of the speaker cables to your speakers.

•Other connections on page 46 provides greater detail on alternate speaker setups, such as using speaker system B (page 48), bi-amping (page 48) and bi- wiring (page 49).

•If you are using a THX certified subwoofer use the THX INPUT jack on the subwoofer (if your subwoofer has one) or switch the filter position to THX on your subwoofer.

Placing the speakers

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.

•The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.

•For the best stereo effect, place the front speakers 2 m to 3 m apart, at equal distance from the TV.

•When placing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference, such as discoloration of the picture when the TV is switched on. If you do not have magnetically shielded speakers and notice discoloration of the TV picture, move the speakers farther away from the TV.

•If you’re using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower angle.

•Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.

•It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.

•Surround and surround back speakers should be positioned 60 cm to 90 cm higher than your ears and titled slight downward. Make sure the speakers don't face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.

•Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

•To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

Front

Center

Front

left

right

 

 

Subwoofer

Surround

 

Surround

left

 

right

Listening position

Surround back left

 

Surround back right

Single surround back speaker

Caution

•Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.

19

En

Image 19
Contents VSX-1017AV-SVSX-1017AV-K Risk of Electric Shock Do not Open Important the Moulded PlugOperating Environment Contents Other connections System Setup menuOther Settings Using other functionsBefore you start FeaturesBefore you start Chapter Before you start Checking what’s in the box Installing the receiverLoading the batteries Introduction to home theater Automatically setting up for surround sound Auto McaccMinute guide 02 5 minute guide ChapterMake sure ‘TYPE1’ is selected then press ENTER.3 Minute guideFollow the instructions on-screen Playing a source Better sound using Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter 342 Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box Connect using a standard video cable or an S-video cableUsing the component video jacks Connecting a DVD/HDD recorder, VCR and other video sourcesDVR, VCR, etc Use a three-way component video cable Connecting using HdmiOn an HDMI-compatible monitor.1 About Hdmi Connecting digital audio sourcesCD-R, MD, DAT, etc This unit has an on-board Windows MediaTM Audio Connecting analog audio sourcesConnect using a stereo RCA/phono jack audio cable About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsTHX speaker system setup Connecting antennasPlug the power cord into a power outlet Connecting external antennasPlugging in the receiver Controls and displays Chapter Controls and displaysFront panel Controls and displays Operating range of remote control unitControls and displays Display Select Controls and displays Remote controlRECEIVER Input SelectReceiver Multi OPEShift SOURCEAuto playback Listening to your systemListening to your system Chapter Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects THX Games ModeListening in stereo Using Front Stage Surround AdvanceSetting the effect options Setting What it does OptionsListening with Acoustic Calibration EQ Listening to your system Using Stream DirectChoosing the input signal Using surround back channel processingPro Logic Using the Virtual Surround Back modePress Tone to select the frequency you want to adjust Listening to your system Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsBasic playback controls Using the USB interfaceUSB playback USB playback ChapterCompressed audio compatibility USB playbackListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAn introduction to RDS Using the tunerNaming station presets Listening to station presetsDisplaying RDS information Using EONPress Disp for RDS information Surround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuFine Channel Level System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuFine Speaker Distance System Setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Volume increases to the reference levelCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ automaticallyChecking your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Speaker Setting System Setup menu Manual speaker setupSelect ‘Manual SP Setup’ then press Enter Channel Level Crossover NetworkTHX Speaker Setup THX Audio SettingSpeaker Distance Other connections Chapter Connecting an iPodConnecting your iPod to the receiver Other connectionsSelecting the multichannel analog inputs Connecting the multichannel analog inputsWatching photos and video content Other connectionsPress Multi CH in front panel Speaker B setupSwitching the speaker system Bi-amping your front speakersBi-wiring your speakers Connecting additional amplifiersLarge Satellite receiver, etc DVD playerPioneer plasma DisplayDVD Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the Hdmi inputs Other SettingsOther Setup menu Dynamic Range Control SetupVideo Converter Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysUsing the sleep timer Using other functionsUsing other functions Chapter Reducing the level of an analog signalPress System Setup to confirm Using other functions Dimming the displaySwitching the speaker impedance Resetting the systemControlling the rest of your system Programming a multi-operation or a shutdown sequence Select the button for the command you want to inputControlling the rest of your system Multi Operation and System OffButtons Function Components Using multi operationsUsing System off Controls for TVsCD/MD/CD-R Decide which component you want to use the remote sensor Additional information Chapter TroubleshootingPower Additional informationSymptomRemedy Other audio problemsAdditional information Video SettingsDisplay Remote controlUSB interface Symptom Cause ActionIPod messages Dolby Additional information Surround sound formatsWindows MediaTM Audio 9 Professional About THXAuto Surround Listening modes with different input signal formatsStereo 2 channel signal formats StandardInput signal format Standard Multichannel signal formatsCleaning the unit Additional information SpecificationsPioneer Corporation