Pioneer VSX-1017AV-S, VSX-1017AV-K manual USB interface, IPod messages, Symptom Cause Action

Page 66

13Additional information

USB interface

SymptomRemedy

USB mass storage device is not recognized by the receiver.

•Try switching the receiver off, then on again.

•Make sure you have completely inserted the USB connector to this receiver.

•Check that the memory format is FAT16 or FAT32 (FAT12, NTFS and HFS are not supported).

•USB devices with an internal USB hub are not supported.

USB ERR3 shows in the display

• If this message continues to appear after going through all the checks in Important on page 34 of USB

when connecting a USB device.

playback, take the unit to your nearest Pioneer authorized service center or your dealer for servicing.

 

 

Can’t play audio files.

• The WMA or MPEG-4 AAC files were recorded using DRM (digital rights management), or the bit rate/

 

sampling rate is not compatible (see Compressed audio compatibility on page 34). This is not a

 

malfunction.

 

 

HDMI

Symptom

Remedy

No picture or sound.

• If the problem still persists when connecting your HDMI component directly to your monitor, please

 

consult the component or monitor manual or contact the manufacturer for support.

 

 

No picture.

• Depending in the output settings of the source component, it may be outputting a video format that can’t

 

be displayed. Change the output settings of the source, or connect using the component, S-video or

 

composite jacks.

 

 

OSD does not appear.

• The OSD will not appear if you have connected using the HDMI output to your TV. Use component, S-video,

 

or composite connections when setting up the system.

 

 

No sound, or sound suddenly

• Since the HDMI audio signal is sent through this receiver to your TV, you need to make separate

ceases.

connections for audio if you want to hear your HDMI component through this system. See Connecting the

 

multichannel analog inputs on page 47 for more on this.

 

• If you’ve made separate connections for audio, make sure you have assigned the analog/digital jack(s) to

 

the corresponding HDMI input for the component. See Assigning the HDMI inputs on page 53 to do this.

 

• Check the audio output settings of the source component.

 

 

iPod messages

Symptom

Cause

Action

Error I1

There is a problem with the signal path from the

Switch off the receiver and reconnect the iPod to the receiver.

 

iPod to the receiver.

If this doesn’t seem to work, try resetting your iPod.

 

 

 

Error I2

The software version being used with the iPod

Update the software being used with the iPod (software

 

needs to be updated.

versions prior to iPod update 2004-10-20 are not supported).

 

 

 

No Music Track

There are no playable songs currently stored in

Input some music files compatible with iPod playback.

 

the iPod.

 

 

 

 

Note

 

 

•If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

66

En

Page 65 Page 67
Image 66
Page 65 Page 67
Contents VSX-1017AV-SVSX-1017AV-K Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Using other functions System Setup menuOther Settings Other connectionsFeatures Before you startBefore you start Chapter Installing the receiver Before you start Checking what’s in the boxLoading the batteries 02 5 minute guide Chapter Automatically setting up for surround sound Auto McaccMinute guide Introduction to home theaterMinute guide Make sure ‘TYPE1’ is selected then press ENTER.3Follow the instructions on-screen 02 5 minute guide Better sound using Phase ControlProblems when using the Auto Mcacc Setup Playing a sourceConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter Connect using a standard video cable or an S-video cable Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box 342Connecting a DVD/HDD recorder, VCR and other video sources Using the component video jacksDVR, VCR, etc Connecting using Hdmi Use a three-way component video cableOn an HDMI-compatible monitor.1 Connecting digital audio sources About HdmiCD-R, MD, DAT, etc About the WMA9 Pro decoder Connecting analog audio sourcesConnect using a stereo RCA/phono jack audio cable This unit has an on-board Windows MediaTM AudioConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupConnecting external antennas Plug the power cord into a power outletPlugging in the receiver Controls and displays Controls and displays ChapterFront panel Operating range of remote control unit Controls and displaysControls and displays Display Input Select Controls and displays Remote controlRECEIVER SelectSOURCE Multi OPEShift ReceiverListening in surround sound Listening to your systemListening to your system Chapter Auto playbackTHX Games Mode Using the Home THX modesUsing the Advanced surround effects Listening to your systemSetting What it does Options Using Front Stage Surround AdvanceSetting the effect options Listening in stereoUsing surround back channel processing Listening to your system Using Stream DirectChoosing the input signal Listening with Acoustic Calibration EQUsing the Virtual Surround Back mode Pro LogicUsing the tone controls Listening to your system Using Midnight and LoudnessUsing the Sound Retriever Press Tone to select the frequency you want to adjustUSB playback Chapter Using the USB interfaceUSB playback Basic playback controlsUSB playback Compressed audio compatibilitySaving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets An introduction to RDSUsing EON Displaying RDS informationPress Disp for RDS information Making receiver settings from the System Setup menu System Setup menuSystem Setup menu Chapter Surround back speaker settingSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu System Setup menu Manual Mcacc setupSelect ‘Manual MCACC’ from the System Setup menu Fine Channel LevelVolume increases to the reference level System Setup menuSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Fine Speaker DistanceSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsFront Align System Setup menu Manual speaker setup Speaker SettingSelect ‘Manual SP Setup’ then press Enter Crossover Network Channel LevelTHX Audio Setting THX Speaker SetupSpeaker Distance Other connections Connecting an iPodConnecting your iPod to the receiver Other connections ChapterOther connections Connecting the multichannel analog inputsWatching photos and video content Selecting the multichannel analog inputsBi-amping your front speakers Speaker B setupSwitching the speaker system Press Multi CH in front panelConnecting additional amplifiers Bi-wiring your speakersLarge Display DVD playerPioneer plasma Satellite receiver, etcDVD Input Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsDynamic Range Control Setup Other SettingsOther Setup menu Assigning the Hdmi inputsSR+ Setup for Pioneer plasma displays Dual Mono SetupLFE Attenuator Setup Video Converter SetupReducing the level of an analog signal Using other functionsUsing other functions Chapter Using the sleep timerResetting the system Using other functions Dimming the displaySwitching the speaker impedance Press System Setup to confirmControlling the rest of your system Multi Operation and System Off Select the button for the command you want to inputControlling the rest of your system Programming a multi-operation or a shutdown sequenceControls for TVs Using multi operationsUsing System off Buttons Function ComponentsCD/MD/CD-R Decide which component you want to use the remote sensor Additional information TroubleshootingPower Additional information ChapterOther audio problems SymptomRemedyAdditional information Settings VideoRemote control DisplaySymptom Cause Action USB interfaceIPod messages Additional information Surround sound formats DolbyAbout THX Windows MediaTM Audio 9 ProfessionalStandard Listening modes with different input signal formatsStereo 2 channel signal formats Auto SurroundMultichannel signal formats Input signal format StandardAdditional information Specifications Cleaning the unitPioneer Corporation
Top Page Image Contents