Telex FMR-500 operating instructions Receiver Push-Button Reference Sheet

Page 4

NOTE: Groups 9 and above are set up to work with the other US frequency band (A and B). If you are using a mix of Band A and Band B, scroll down to these groups and use the clearest group.

6.Change Lock-Out: By pressing and holding the UP and DOWN arrow keys together for 3 sec- onds, the SET key is disabled.To reactivate the SET key, simply press and hold the UP and DOWN keys again for 3 seconds. This feature can be useful when the receiver is in a location where unauthorized personnel have access to the receiver.

7.For set up, make sure the mixer or amplifier in- put used for the FMR-500 is muted or turned down to a minimum level.

8.Plug an audio cable (not supplied) into the 3 pin XLR or 1/4 inch output of the FMR-500.

a.NOTE: The XLR connector is the pre- ferred connection since the output is bal- anced and will be more immune to noise for longer runs of cable although either can be used with good results. If the 1/4 inch connector is used, adjust the output level on the back panel to 12 o'clock (mid- way in the range) to start and adjust later if necessary.

Now refer ahead to transmitter setup and return to step 9 when that is completed.

9.With the transmitter on, speak into the micro- phone or play the guitar. Turn up the level on the mixer or amplifier until you are able to hear the desired signal. If no audio is present, repeat setup and refer to the troubleshooting section.

NOTE: If the 1/4 inch output is used, it may be necessary to adjust the receiver output until the volume level from the wireless system approxi- mates the level of an equivalent wired micro- phone/instrument.

10.Squelch Adjustment - The squelch setting can be used to maximize range or immunity to noise. Press and hold Up for 3 seconds. The cur- rent squelch setting will be displayed. Adjust the squelch using the UP/DOWN keys. Maxi- mum squelch (9) maximizes noise immunity but limits the range. Minimum squelch (1) will maxi- mize the range but allow more noise to break through the squelch. Press SET to save the new squelch setting.

Receiver Push-Button Reference Sheet

Display

Status Button

Function Activated

Edit

Accept

Nothing Flashing

Press and hold SET

Auto ClearScan

n/a

n/a

Nothing Flashing

SET

Edit Group -Group will flash

 

SET

Group Flashing

Press and hold SET

ClearScan Group - list clear groups in order

 

SET

Group Flashing

SET

Edit Channel - Channel will flash

 

SET

Channel Flashing

Press and hold SET

ClearScan Channel - list clear channels in order

 

SET

Nothing Flashing

Press and hold Up

Edit Squelch Setting

 

SET

Nothing Flashing

Press and hold Up & Down

Edit Lock - Secure will appear

n/a

n/a

Edit Lock On

Press and hold Up & Down

Return to Access Mode

n/a

n/a

Power Off

Press and hold SET

Toggle between Guitar and Voice mode

n/a

n/a

Nothing Flashing

Press SET and Up

Toggle to Frequency Mode - Freq will flash

 

SET

Frequency Flashing

Press and hold SET

ClearScan Band - Clear Scan will flash

n/a

SET

ClearScan Band Running

Press SET

End ClearScan Band after next full scan

n/a

n/a

ClearScan Band Results

n/a

Clearest frequencies listed

 

SET

Frequency Mode

Press SET and Up

Return to Group and Channel Mode

n/a

n/a

Nothing Flashing

Press and hold Down

Display Software Revision

n/a

n/a

 

 

 

 

 

-3-

Image 4
Contents FMR-500 Quick Set-Up System DescriptionQuick Set-up Receiver Quick set-up TransmitterReceiver Setup and Operation FMR-500 Receiver Controls, Connectors, and IndicatorsDetailed Components Description Receiver Push-Button Reference Sheet Display Status Button Function Activated Edit AcceptRack Mount Installation Rack Mount InstallationFront Mounting Antennas Front Mounting AntennasHT-500 Controls Connectors, and Indicators Handheld Transmitter Setup and OperationHandheld Transmitter HT-500 Handheld TransmitterWT-500 Controls, Connectors, and Indicators Bodypack Transmitter WT-500Bodypack Transmitter Control View Top ViewBodypack Transmitter Setup and Operation Attach the Microphone or GuitarSquelch Adjustment Screen Receiver Display Screens and FunctionsMain Operating Screen Transmitter Display and ControlsUsing Multiple Wireless Systems Battery RecommendationsReceiver and Antenna Placement Transmitter On/Off Lock-OutTrouble Shooting Guide Problem Possible Causes SolutionsTrouble Shooting Guide Problem Possible Causes Solutions Technical Specifications Specifications OverallAudio Parameters Transmitters WT-500 and HT-500Accessories and Parts Model No Order NoFactory Service North America Factory Service/Warranty LimitedWarranty Limited