Pioneer VSX-01TXH manual Speaker Distance, Curve, THX Audio Setting

07The System Setup menu

Speaker Distance

For good sound depth and separation from your system, you need to specify the distance of your speakers from the listening position. The receiver can then add the proper delay needed for effective surround sound.

1 Select ‘X-Curve’ from the Manual SP Setup menu.

5.Manual SP

Setup

5d.X-Curve

a . Speaker

Setting

X-Curve

-2.0dB/oct

b . Channel

Level

c . Speaker

Distance

d . X-Curve

e . THX Audio Setting

63

125

250

500

1k

2k

4k

8k

16k

Important

•When Speaker Distance is selected while MCACC is set to OFF, the selection screen for the MCACC memory appears. Select a memory to adjust manually.

5c.Speaker Distance

Select MCACC memory.

MCACC OFF

M1.MEMORY 1

ENTER:Next :Cancel

1Select ‘Speaker Distance’ from the Manual SP Setup menu.

:Return :Finish

2 Choose the X-Curve setting you want.

Use / to adjust the setting. The X-Curve is expressed as a downwards slope in decibels per octave, starting at 2 kHz. The sound becomes less bright as the slope increases (to a maximum of –3.0dB/oct). Use the following guidelines to set the X-Curve according to your room size:

Room size (ft2)	≤400	≤550	≤650	≤800	≤2200	≤12000
X-Curve (dB/oct)	–0.5	–1	–1.5	–2	–2.5	–3

•If you select OFF, the frequency curve will be flat and the X-Curve has no effect.

5.Manual SP Setup

a . Speaker Setting

b . Channel Level

c . Speaker Distance

d . X-Curve

e . THX Audio Setting

:Return

2Adjust the distance of each speaker using /. You can adjust the distance of each speaker in 1 inch increments.

5c.Speaker

Distance

5c.Speaker

Distance

MCACC

: M1.MEMORY 1

MCACC

: M1

.MEMORY 1

SR

0

' 11

''

L

10

' 00 ''

SBR

[

11 ' 09 ''

]

C

[

0

' 11 ''

]

SBL

[ 12

' 05

''

]

R

[

11 ' 09 '' ]

SL

[ 13

' 10

''

]

SW

[ 45

' 00

'' ]

:Finish

:Finish

3When you’re finished, press RETURN. You will return to the Manual SP Setup menu.

Tip

•For best surround sound, make sure the surround back speakers are the same distance from the listening position.

X-Curve

3 Select ‘Return’, then press ENTER to finish.

THX Audio Setting

When the THX Loudness Plus function is used, sound can be played with the full surround effect even when the volume is low.

For the most effective results when using the THX SELECT2 Cinema, THX SELECT2 Music and THX SELECT2 Games listening modes (see Using the Home THX modes on page 31) with the Advanced Speaker Array (ASA) system (see About THX on page 93), it is required that you make the setting. See Placing the speakers on

page 22 for more on THX speaker placement.2

1Select ‘THX Audio Setting’ from the Manual SP Setup menu.

5.Manual SP Setup

a . Speaker Setting

b . Channel Level

c . Speaker Distance

d . X-Curve

e . THX Audio Setting

:Return

2Select either ON or OFF for THX Loudness Plus setting.

Most soundtracks mixed for cinema sound too bright when played back in large rooms. The X-Curve setting acts as a kind of re-equalization for home theater listening, and restores proper tonal balance of movie

soundtracks.1

5e.THX Audio Setting

Loudness Plus ON SB SP Position

0 - 1 ft

:Finish

Note

1Since the principal is the same, X-Curve isn’t applied when you’re using any of the Home THX modes (see Using the Home THX modes on page 31).

2If you don’t have surround back speakers, or have only one surround back speaker or select Speaker B, Front Bi-Amp or ZONE 2 for Surround Back System, you won’t be able to select this setting (Cannot select shows in the display).

50

En