American DJ TP-DMX24F specifications Dimmer Setting in Manual Mode, Codes

Page 6

OPERATING INSTRUCTIONS Cont.

2.3 DIMMER SETTING IN MANUAL MODE

To adjust DIMMING/VALUE of any channel in Manual mode.

A. Enter CHASE PROGRAM mode, Touch any (FIG 2.) CHANNEL 1-24when LED is on touch same channel again until LED starts to blink. You can now use (FIG12 ) DIMMER FADER to adjust output. Set as many CHANNELS as you want in this manner.

B. Touch (FIG 9.) RECORD CHASE button for 0.5 sec until all LED’s blink. This means output has been memorized.

2.3.1CODES

The following are codes entered using the (FIG.1.) CHASE 1-12buttons.

ENTER PROGRAM MODE

A. Touch (FIG 6.) ASSIGN SCENE /BLIND and (FIG 9.) RECORD CHASE at the same time. for 0.5 sec.

LED’s will light for these and for HOLD on (FIG 3.) CH 1-24 HOLD/FLASH .

B. Touch in sequence (FIG.1.) CHASE 8 , (FIG.1.) CHASE 9 , (FIG.1.) CHASE 6 , (FIG.1.) CHASE 2 , all LED’s will blink 3 times and LED’s on HOLD ASSIGN SCENE AND RECORD CHASE WILL REMAIN LIT. if correct code is entered. If a mistake was made the LED’s will turn off and you need to repeat step 2A.. and 2B.

DELETE CHASING PROGRAM

A. Touch (FIG 6.) ASSIGN SCENE /BLIND and (FIG 9.) RECORD CHASE at the same time. for 0.5 sec.

LED’s will light for these and for HOLD on (FIG 3.) CH 1-24 HOLD/FLASH .

B. Touch in sequence (FIG.1.) CHASE 9 , (FIG.1.) CHASE 6 , (FIG.1.) CHASE 5, then (FIG.1.) CHASE # you want to delete, all LED’s will blink 3 times and LED’s will turn off.

CLEAR ALL(CHASE PROGRAM/ASSIGN SCENE PROGRAM / CHANNEL OUTPUT.

A. Touch (FIG 6.) ASSIGN SCENE /BLIND and (FIG 9.) RECORD CHASE at the same time. for 0.5 sec.

LED’s will light for these and for HOLD on (FIG 3.) CH 1-24 HOLD/FLASH .

B. Touch in sequence (FIG.1.) CHASE 9 , (FIG.1.) CHASE 6 , (FIG.1.) CHASE 8, (FIG.1.) CHASE 1 , all LED’s will blink 3 times and LED’s will turn off.

EVERYTHING MEMORIZED IN TP-DMX24F WILL BE ERASED!

3. RECORD / CHASE

Once you have programmed TP-DMX24F you can run RECORD / CHASE.

In MANUAL MODE touch (FIG 9.) RECORD CHASE for 0.5sec. LED is lit. If Chase LED of (FIG 7.) AUDIO PERCENT TRAITS CHASE is lit the unit is in CHASE mode. If SINGLE LED of (FIG10.) SINGLE CHASE / MIX CHASE / STEP is lit, the unit is in SINGLE CHASE. You can touch

(FIG10.) SINGLE CHASE / MIX CHASE / STEP to select MIX Chase.

In SINGLE CHASE mode, all selected chasing programs are run in the order you selected them. In MIX CHASE mode, all selected chasing programs are run at the same time.

TP-DMX24F™ Instructions page 6

Image 6
Contents 1 / SpecificationsControls and Functions Real Time /TAP SyncControls and Functions Operating Instructions Program Manual ModeOperating Instructions Chase ProgramChase Program Assign Scene ProgramRecord Chase Insert and Delete Steps Dimmer Setting in Manual Mode CodesEverything Memorized in TP-DMX24F will be Erased Assign Scene Real Time Edit Using . Assign Scene /BLIND ButtonRecord / Chase BlackoutPerating Instructions Midi Setting and RunningMidi Setting Midi Running