Denon DJ DN-X1700 owner manual Part Names and Functions, Top Panel

Page 7

Part Names and Functions

 

 

 

 

 

 

qMASTER LEVEL control

 

 

 

 

 

 

Adjusts the level of the MASTER outputs.

For further details on the functions and other aspects

of

the

parts, refer to

the

page

numbers in

The LIMITER LED indicates the operating status

of the master output limiter.

parenthesis.

 

 

 

 

 

 

 

• Limiter OFF: LED is off.

Top Panel

 

 

 

 

 

 

 

• Limiter ON: LED lights up green.

 

 

 

 

 

 

 

• While limiter is operating: LED lights up red.

 

 

 

 

 

 

 

 

wMaster EFX INS 1, 2 buttons

E1 E3

E2

 

 

E5R1R2

 

 

 

These buttons enable the various effects of

 

 

 

 

 

the selected side, either EFX 1 or EFX 2, to be

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

obtained for the master output signals.

 

 

 

 

 

 

 

 

eBOOTH LEVEL control

 

 

 

 

 

 

 

q

Adjusts the level of the BOOTH outputs.

R3

 

 

 

 

 

 

rUSB ASSIGN CH/MASTER button

 

 

 

 

 

 

 

 

This is used to switch the assignment destination

E0

 

 

 

 

 

 

w

of the USB audio input signals supplied from the

 

 

 

 

 

 

 

computer.

 

 

 

 

 

 

 

e

CH:

 

 

 

 

 

 

 

The signals are assigned to the channels (1 to 4).

W9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MASTER:

 

 

 

 

 

 

 

 

 

 

 

r

The signals are assigned to the master bus and

W8

 

 

monitor bus.

 

 

t

tMIDI CLOCK START/STOP button

 

 

 

 

 

 

y

This enables the MIDI clock corresponding to

 

 

 

E4

the BPM value to be sent from the USB MIDI

W7

 

 

E6

and MIDI

output terminals to the computer

 

 

E7

(software) or external device.

 

 

 

W6

 

 

E8

START:

 

 

 

Sending the MIDI clock is started.

W5

 

 

u

 

 

STOP:

 

 

 

 

i

 

W4

 

 

Sending the MIDI clock is stopped.

 

 

o

W3

 

 

yUTILITY/–USB A/USB B button

 

 

Q0

This allows the presets to be set and the system

W2

 

 

 

 

Q1

information to be set, changed or referenced.

 

 

 

 

 

 

When it is held down for more than a second,

 

 

 

 

W1

 

 

 

the USB mode switching screen is opened, and

W0

 

 

Q2

the USB device mode or USB host mode can

 

 

 

Q3

be selected.

Q9

 

 

uBEAT ,

buttons

 

 

Q4

 

 

 

 

 

(Short) :

 

 

 

 

Q8

 

 

 

The beat/time is decreased.

 

 

Q5

(Long) :

 

 

 

 

 

 

 

The beat/time is increased.

R0

Q7

Q6

E9

 

 

iTAP LOCK/AUTO/INPUT BPM button

TAP:

When this button is tapped repeatedly, the BPM (Beats Per Minute) value is measured using the intervals between the taps.

LOCK:

When the button is pressed once in the auto BPM mode, the BPM value measured automatically is locked.

AUTO BPM:

When the button is held down for one second, the auto BPM mode is established, and the measured BPM value is displayed.

INPUT BPM:

When it is held down for two or more seconds, the BPM input mode is established, and the BPM value can be input directly using the

uBEAT , buttons. When it is pressed again, the mode is released.

oTIME/BACK button

TIME:

This button is used to select whether to change

the effects produced using the u BEAT , buttons on the basis of the number of beats

or time.

BACK (EFX 2 side only):

This is used when returning to the previous screen while setting screen operations are being performed.

Q0Effect CUE button

When this button is set to ON, the sound of the effects (but not the DELAY, ECHO or REVERB effects) can be monitored even if the effect OFF status.

Q1EFX SELECT control

This is for selecting the effect to be used. Refer to the effect functions (page 9).

Q2Parameter ON/OFF button

This is used to control the ON and OFF settings of the effect parameters.

Q3PARAMETER MIX/MAX control

This is used to adjust the filter cutoff frequency and other effector parameters. The parameters are changed by the effector selected.

Q4DRY/WET control

Use this to adjust the ratio of original and effected sound.

Getting Started Connections Basic Operations Effector Function Fader Start USB Utility Specifications Troubleshooting

3

Image 7
Contents DN-X1700 Important Safety Instructions Attenzione AchtungDeclaration of Conformity ÜbereinstimmungserklärungAcerca DEL Reciclaje Hinweis ZUM RecyclingUNE Remarque Concernant LE Recyclage Nota Relativa AL RiciclaggioContents InstallationGetting Started Dual effect Main FeaturesOther features Design oriented toward achieving a high sound qualityTop Panel Part Names and FunctionsThru Q6CROSSFADERPhono R3SIG/PKRear Panel Display Preparations ConnectionsCables Used for Connections Ducking function Monitor headphones outputBasic Operations MIC mic inputDetails of operation Effector FunctionBeatBreaker Function What the BeatBreaker effector doesAuto Setting the BPMEffecter Screen Effecter OperationsChannel Fader Start Fader StartCrossfader Start How to adjust the Crossfader torque Fader setting the fader curveSetting the USB audio output USB SettingsSelecting the USB mode USB audio Setting the USB audio inputSetting the Midi clock Setting the Midi channelsMidi layer operations Send commands Midi Command ListLED Receive commandsPreset Items and Data Category Parameter Value Default Utility settingsUtility operations Owner Setting Mode Preset ExportPreset Recall Preset ImportSpecifications Block Diagram Troubleshooting TOKYO, Japan
Related manuals
Manual 26 pages 38.06 Kb