Vestax PMC 250 owner manual Monitor Section, Rear Panel Section

Page 7

MONITOR SECTION

MONITOR

CUE SELECTOR

STEREO CUE LEVEL

PHONES

 

 

 

ON

 

 

 

 

OFF

 

1

AUX

2

MIN

MAX

 

 

 

21 22 23 24

@2STEREO CUE (Stereo Cue ON/OFF Switch)

When this switch is set to ON, the input signal selected by CUE SELECTOR can be monitored in stereo through headphones. When this switch is set to OFF, the master signal can be monitored through the right side of the headphone all the time, the CUE signal selected by CUE SELECTOR will be heard from the left side. This feature allows DJs to monitor current and next source simultaneously.

@1CUE SELECTOR

Used to select the cue signal to be monitored by headphones from PGM1, PGM2 or AUX.

REAR PANEL SECTION

30

@3LEVEL (Headphone Level)

Adjust the monitor level of the headphones.

@4PHONES (Headphone Jack)

Used to connect the headphones. Headphones with impedance from 8-600 can be used.

28

26

25

29

34 35

33

@5PHONO 1,2 [RCA PIN JACK]

Connect turntables equipped with MM (Moving Magnet type) cartridge. The signal from the turntable is fed to the PGM channels when Phono input is selected.

@6LINE 1,2,3,4 [RCA PIN JACK]

Connect the equipment with line level output (-10dB, 0dB, +6dB), such as CD players, tape decks, DATs, MDs etc. The signal from line level equipment is fed to the PGM channels when Line input is selected.

@7AUX IN (LINE 5, PHONO 3) [RCA PIN JACK]

Input jack for turntable and line level equipment. The signal from these jacks are fed to AUX input channel.

@8INPUT LEVEL[+6/0/-10dB]

Used to select the input level.

32

31

27

28

28

26

25 29

@9GND (Ground Terminal)

Connect the ground lead from the turntable. Failure to connect a ground lead produces noise on Phono input signal.

#0PA OUT (Balanced Output) [XLR MALE, 2 PIN HOT]

Main output jacks. Connect to the input of the power amplifier or the master console with XLR 3 pin cable.

#1PAOUTLEVEL(BalancedOutputLevelSelectSwitch)[-10dB/0dB]

Used to select the output level of the PA OUT from -10dB or 0dB. Please select the level according to the input sensitivity of the power amplifier or the master console.

#2LINE OUT (Unbalanced Output) [1/4" PHONE JACK]

Unbalanced LINE output. Connect to the input of the power amplifier or the master console with 1/4" phone cable. PA OUT LEVEL (#1) does not effect this output.

CAUTION

When the line level equipment is connected to LINE 5 input jack, the input signal from PHONO 3 is disconnected and only the signal from line level equipment is fed to AUX input. Please disconnect LINE 5 when turntable is used.

#3BOOTH OUT(Output for Monitor System) [1/4" PHONE JACK]

Connect to the input of the power amplifier of the DJ booth monitor system.

#4POWER (Power Switch) #5AC IN

Connect the AC-12A AC Adapter. (12V AC, 1000mA)

6

Image 7
Contents Professional Mixing Controller CONGRATULATIONS! ContentsA D B E F O R E O P E R AT I N G E QU I P M E N T Important SafeguardsA T U R E S Program Section Microphone Section Master SectionRear Panel Section Monitor SectionTURNTABLE[VESTAX PDX-2000]TURNTABLE[VES N N E C T I O N E X a M P L EHOW to Change the Fader Unit HOW to Change the Fader UnitHOW to Change the Jack Panel Position PGM-1 BlockSpecification S